[dpdk-dev] [PATCH v2] ixgbe_vf: Fix getting link state

Balazs Nemeth balazs.nemeth at intel.com
Thu Dec 18 18:56:36 CET 2014


This patch fixes checking the link state of a virtual function. If the
state has already been checked, it does not need to be checked
again. Previously, get_link_status in the ixgbe_hw struct was used to
track if the information had already been retrieved, but this field
was always set to false (signifying that the information was
up-to-date). The problem was introduced by commit 8ef32003 which was
part of a patch set to update the ixgbe portion of the PMD. This patch
does not break consistency with the ixgbevf driver. Instead, it fixes
the problem at the level of DPDK.

Applications that rely on the reported link speed could fail without
this patch. The qos_sched example application provided with DPDK did
not run when virtual functions were used. The output for this example
application is shown below:

EAL: Error - exiting with code: 1
  Cause: Unable to config sched subport 0, err=-2

The problem and the effect of the patch can been seen by running the
l2fwd example application using the following command:

sudo ./build/l2fwd -c 0x3 -n 4 -- -p 0x3 -T 0

Before the patch has been applied (with both links up):
...
Checking link statusdone
Port 0 Link Up - speed 100 Mbps - half-duplex

Port 1 Link Up - speed 100 Mbps - half-duplex

L2FWD: entering main loop on lcore 1
...

After the patch has been applied (with both links up):
...
Checking link statusdone
Port 0 Link Up - speed 10000 Mbps - full-duplex
Port 1 Link Up - speed 10000 Mbps - full-duplex
L2FWD: entering main loop on lcore 1
...

Before the patch has been applied (with link 0 down, link 1 up):
...
Checking link statusdone
Port 0 Link Up - speed 100 Mbps - half-duplex

Port 1 Link Up - speed 100 Mbps - half-duplex

L2FWD: entering main loop on lcore 1
...

After the patch has been applied (with link 0 down, link 1 up):
...
Checking link status............................................................
..............................done
Port 0 Link Down
Port 1 Link Up - speed 10000 Mbps - full-duplex
...

Signed-off-by: Balazs Nemeth <balazs.nemeth at intel.com>
---

changes v2:
* Include more elaborate explanation of the problem in the commit message
* Fix the issue at the level of DPDK not touching ixgbe driver code

 lib/librte_pmd_ixgbe/ixgbe_ethdev.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
index 9401916..22227e6 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
+++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
@@ -1469,6 +1469,7 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
 	if (status != 0)
 		return -1;
 	hw->mac.ops.start_hw(hw);
+	hw->mac.get_link_status = true;

 	/* configure PF module if SRIOV enabled */
 	ixgbe_pf_host_configure(dev);
@@ -2064,7 +2065,7 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
 {
 	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
 	struct rte_eth_link link, old;
-	ixgbe_link_speed link_speed;
+	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
 	int link_up;
 	int diag;

@@ -2088,6 +2089,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
 		return 0;
 	}

+	if (link_speed == IXGBE_LINK_SPEED_UNKNOWN &&
+	    !hw->mac.get_link_status) {
+		memcpy(&link, &old, sizeof(link));
+		return -1;
+	}
+
 	if (link_up == 0) {
 		rte_ixgbe_dev_atomic_write_link_status(dev, &link);
 		if (link.link_status == old.link_status)
@@ -2926,6 +2933,7 @@ ixgbevf_dev_start(struct rte_eth_dev *dev)
 	PMD_INIT_FUNC_TRACE();

 	hw->mac.ops.reset_hw(hw);
+	hw->mac.get_link_status = true;

 	/* negotiate mailbox API version to use with the PF. */
 	ixgbevf_negotiate_api(hw);
--
2.1.3


More information about the dev mailing list