[dpdk-dev] [PATCH 11/26] ixgbe/base: restore ESDP settings after MAC reset
Wenzhuo Lu
wenzhuo.lu at intel.com
Fri Jun 5 07:21:43 CEST 2015
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. So,
put the code in a function so it can be used in more than one place.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu at intel.com>
---
drivers/net/ixgbe/base/ixgbe_x550.c | 41 ++++++++++++++++++++-----------------
1 file changed, 22 insertions(+), 19 deletions(-)
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c b/drivers/net/ixgbe/base/ixgbe_x550.c
index c91e737..319aa0d 100644
--- a/drivers/net/ixgbe/base/ixgbe_x550.c
+++ b/drivers/net/ixgbe/base/ixgbe_x550.c
@@ -264,6 +264,23 @@ STATIC void ixgbe_check_cs4227(struct ixgbe_hw *hw)
}
/**
+ * ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control
+ * @hw: pointer to hardware structure
+ **/
+STATIC void ixgbe_setup_mux_ctl(struct ixgbe_hw *hw)
+{
+ u32 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
+
+ if (hw->bus.lan_id) {
+ esdp &= ~(IXGBE_ESDP_SDP1_NATIVE | IXGBE_ESDP_SDP1);
+ esdp |= IXGBE_ESDP_SDP1_DIR;
+ }
+ esdp &= ~(IXGBE_ESDP_SDP0_NATIVE | IXGBE_ESDP_SDP0_DIR);
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
+ IXGBE_WRITE_FLUSH(hw);
+}
+
+/**
* ixgbe_identify_phy_x550em - Get PHY type based on device id
* @hw: pointer to hardware structure
*
@@ -271,20 +288,11 @@ STATIC void ixgbe_check_cs4227(struct ixgbe_hw *hw)
*/
STATIC s32 ixgbe_identify_phy_x550em(struct ixgbe_hw *hw)
{
- u32 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
-
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_X_SFP:
/* set up for CS4227 usage */
hw->phy.phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
- if (hw->bus.lan_id) {
-
- esdp &= ~(IXGBE_ESDP_SDP1_NATIVE | IXGBE_ESDP_SDP1);
- esdp |= IXGBE_ESDP_SDP1_DIR;
- }
- esdp &= ~(IXGBE_ESDP_SDP0_NATIVE | IXGBE_ESDP_SDP0_DIR);
- IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
-
+ ixgbe_setup_mux_ctl(hw);
ixgbe_check_cs4227(hw);
return ixgbe_identify_module_generic(hw);
@@ -1099,20 +1107,12 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
{
struct ixgbe_phy_info *phy = &hw->phy;
s32 ret_val;
- u32 esdp;
DEBUGFUNC("ixgbe_init_phy_ops_X550em");
if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP) {
- esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
-
- if (hw->bus.lan_id) {
- esdp &= ~(IXGBE_ESDP_SDP1_NATIVE | IXGBE_ESDP_SDP1);
- esdp |= IXGBE_ESDP_SDP1_DIR;
- }
- esdp &= ~(IXGBE_ESDP_SDP0_NATIVE | IXGBE_ESDP_SDP0_DIR);
- IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
+ ixgbe_setup_mux_ctl(hw);
}
/* Identify the PHY or SFP module */
@@ -1269,6 +1269,9 @@ mac_reset_top:
hw->mac.ops.init_rx_addrs(hw);
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP)
+ ixgbe_setup_mux_ctl(hw);
+
return status;
}
--
1.9.3
More information about the dev
mailing list