[dpdk-dev] [PATCH v3 00/36] update e1000 base code

Lu, Wenzhuo wenzhuo.lu at intel.com
Wed Oct 28 02:58:10 CET 2015


Hi Thomas,

> -----Original Message-----
> From: Thomas Monjalon [mailto:thomas.monjalon at 6wind.com]
> Sent: Tuesday, October 27, 2015 11:34 PM
> To: Lu, Wenzhuo
> Cc: dev at dpdk.org; Mcnamara, John
> Subject: Re: [dpdk-dev] [PATCH v3 00/36] update e1000 base code
> 
> 2015-10-16 10:50, Wenzhuo Lu:
> > Wenzhuo Lu (36):
> >   e1000/base: update readme and copyright
> >   e1000/base: add new devices
> >   e1000/base: fix issue with link flap on 82579
> >   e1000/base: fix issue with jumbo frame CRC failures in client
> >   e1000/base: redundant PHY power down for i210
> >   e1000/base: add return value to the functions of setting receive
> >     address register
> >   e1000/base: add defaults for i210 TX/RX PBSIZE
> >   e1000/base: remove E1000_WRITE_FLUSH for DH89XXCC_SGMII after
> >     commencing HW reset
> >   e1000/base: add evaluation of e1000_nvm_read return value
> >   e1000/base: change invariant return to not use variables
> >   e1000/base: add return value handler when check manage mode
> >   e1000/base: add return value handler for ESB2 controller init and
> >     reset
> >   e1000/base: add support for inverted format ETrackId
> >   e1000/base: add EEARBC_I210 for i210
> >   e1000/base: apply paranoia to macro arguments
> >   e1000/base: add flags to set eee advertisement modes
> >   e1000/base: prevent ulp flow if cable connected
> >   e1000/base: fix TIPG value for non 10 half duplex mode
> >   e1000/base: add return value for resume workaround
> >   e1000/base: fix link detect flow
> >   e1000/base: cleanup NAHUM6LP_HW tags
> >   e1000/base: add bit for disable packetbuffer read
> >   e1000/base: K1 flow fixes
> >   e1000/base: remove FIXME comment
> >   e1000/base: set correct value of beacon duration
> >   e1000/base: disable extension header parsing for IPv6
> >   e1000/base: fix for i354 88E1112 PHY using AutoMedia Detect
> >   e1000/base: increase timeout of polling bit RSPCIPHY in
> >     check_reset_block
> >   e1000/base: implement 88E1543 PHY initialization
> >   e1000/base: use the correct i210 register for EEMNGCTL
> >   e1000/base: move the print to the right position
> >   e1000/base: synchronization of MAC-PHY interface only on non- ME
> >     systems
> >   e1000/base: fix to enable both ulp and EEE in Sx state
> >   e1000/base: some minor change
> >   e1000: add new devices
> >   doc: update release notes for e1000 base code update
> 
> Applied without the release notes patch which is not ready.
> The git titles have been reworded to be easier to read and understand.
> It may help to reword the release notes.
> Thanks

Thanks for applying the patches. I'll send a patch to reword the release notes. Thanks.


More information about the dev mailing list