[dpdk-dev] [PATCH v2 1/6] ethdev: add descriptor status API

Yang, Qiming qiming.yang at intel.com
Tue Mar 21 09:32:17 CET 2017


Hi, Olivier
You need to add your new API in lib/librte_ether/rte_ether_version.map and doc/guides/rel_notes/release_17_05.rst

> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Olivier Matz
> Sent: Wednesday, March 8, 2017 12:00 AM
> To: dev at dpdk.org; thomas.monjalon at 6wind.com; Ananyev, Konstantin
> <konstantin.ananyev at intel.com>; Lu, Wenzhuo <wenzhuo.lu at intel.com>;
> Zhang, Helin <helin.zhang at intel.com>; Wu, Jingjing <jingjing.wu at intel.com>;
> adrien.mazarguil at 6wind.com; nelio.laranjeiro at 6wind.com
> Cc: Yigit, Ferruh <ferruh.yigit at intel.com>; Richardson, Bruce
> <bruce.richardson at intel.com>; Venkatesan, Venky
> <venky.venkatesan at intel.com>; arybchenko at solarflare.com
> Subject: [dpdk-dev] [PATCH v2 1/6] ethdev: add descriptor status API
> 
> Introduce a new API to get the status of a descriptor.
> 
> For Rx, it is almost similar to rx_descriptor_done API, except it differentiates
> "used" descriptors (which are hold by the driver and not returned to the
> hardware).
> 
> For Tx, it is a new API.
> 
> The descriptor_done() API, and probably the rx_queue_count() API could be
> replaced by this new API as soon as it is implemented on all PMDs.
> 
> Signed-off-by: Olivier Matz <olivier.matz at 6wind.com>
> ---
>  doc/guides/nics/features/default.ini |   2 +
>  lib/librte_ether/rte_ethdev.h        | 125
> +++++++++++++++++++++++++++++++++++
>  2 files changed, 127 insertions(+)
> 
> diff --git a/doc/guides/nics/features/default.ini
> b/doc/guides/nics/features/default.ini
> index 9e363ff..0e6a78d 100644
> --- a/doc/guides/nics/features/default.ini
> +++ b/doc/guides/nics/features/default.ini
> @@ -49,6 +49,8 @@ Inner L3 checksum    =
>  Inner L4 checksum    =
>  Packet type parsing  =
>  Timesync             =
> +Rx Descriptor Status =
> +Tx Descriptor Status =
>  Basic stats          =
>  Extended stats       =
>  Stats per queue      =
> diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h
> index 97f3e2d..904ecbe 100644
> --- a/lib/librte_ether/rte_ethdev.h
> +++ b/lib/librte_ether/rte_ethdev.h
> @@ -1179,6 +1179,12 @@ typedef uint32_t
> (*eth_rx_queue_count_t)(struct rte_eth_dev *dev,  typedef int
> (*eth_rx_descriptor_done_t)(void *rxq, uint16_t offset);  /**< @internal
> Check DD bit of specific RX descriptor */
> 
> +typedef int (*eth_rx_descriptor_status_t)(void *rxq, uint16_t offset);
> +/**< @internal Check the status of a Rx descriptor */
> +
> +typedef int (*eth_tx_descriptor_status_t)(void *txq, uint16_t offset);
> +/**< @internal Check the status of a Tx descriptor */
> +
>  typedef int (*eth_fw_version_get_t)(struct rte_eth_dev *dev,
>  				     char *fw_version, size_t fw_size);  /**<
> @internal Get firmware information of an Ethernet device. */ @@ -1483,6
> +1489,10 @@ struct eth_dev_ops {
>  	eth_queue_release_t        rx_queue_release; /**< Release RX queue.
> */
>  	eth_rx_queue_count_t       rx_queue_count;/**< Get Rx queue
> count. */
>  	eth_rx_descriptor_done_t   rx_descriptor_done; /**< Check rxd DD
> bit. */
> +	eth_rx_descriptor_status_t rx_descriptor_status;
> +	/**< Check the status of a Rx descriptor. */
> +	eth_tx_descriptor_status_t tx_descriptor_status;
> +	/**< Check the status of a Tx descriptor. */
>  	eth_rx_enable_intr_t       rx_queue_intr_enable;  /**< Enable Rx
> queue interrupt. */
>  	eth_rx_disable_intr_t      rx_queue_intr_disable; /**< Disable Rx
> queue interrupt. */
>  	eth_tx_queue_setup_t       tx_queue_setup;/**< Set up device TX
> queue. */
> @@ -2768,6 +2778,121 @@ rte_eth_rx_descriptor_done(uint8_t port_id,
> uint16_t queue_id, uint16_t offset)
>  		dev->data->rx_queues[queue_id], offset);  }
> 
> +#define RTE_ETH_RX_DESC_AVAIL    0 /**< Desc available for hw. */
> +#define RTE_ETH_RX_DESC_DONE     1 /**< Desc done, filled by hw. */
> +#define RTE_ETH_RX_DESC_UNAVAIL  2 /**< Desc used by driver or hw. */
> +
> +/**
> + * Check the status of a Rx descriptor in the queue
> + *
> + * It should be called in a similar context than the Rx function:
> + * - on a dataplane core
> + * - not concurrently on the same queue
> + *
> + * Since it's a dataplane function, no check is performed on port_id
> +and
> + * queue_id. The caller must therefore ensure that the port is enabled
> + * and the queue is configured and running.
> + *
> + * Note: accessing to a random descriptor in the ring may trigger cache
> + * misses and have a performance impact.
> + *
> + * @param port_id
> + *  A valid port identifier of the Ethernet device which.
> + * @param queue_id
> + *  A valid Rx queue identifier on this port.
> + * @param offset
> + *  The offset of the descriptor starting from tail (0 is the next
> + *  packet to be received by the driver).
> + *
> + * @return
> + *  - (RTE_ETH_RX_DESC_AVAIL): Descriptor is available for the hardware to
> + *    receive a packet.
> + *  - (RTE_ETH_RX_DESC_DONE): Descriptor is done, it is filled by hw, but
> + *    not yet processed by the driver (i.e. in the receive queue).
> + *  - (RTE_ETH_RX_DESC_UNAVAIL): Descriptor is unavailable, either hold by
> + *    the driver and not yet returned to hw, or reserved by the hw.
> + *  - (-EINVAL) bad descriptor offset.
> + *  - (-ENOTSUP) if the device does not support this function.
> + *  - (-ENODEV) bad port or queue (only if compiled with debug).
> + */
> +static inline int
> +rte_eth_rx_descriptor_status(uint8_t port_id, uint16_t queue_id,
> +	uint16_t offset)
> +{
> +	struct rte_eth_dev *dev;
> +	void *rxq;
> +
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> +	RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV); #endif
> +	dev = &rte_eth_devices[port_id];
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> +	if (queue_id >= dev->data->nb_rx_queues)
> +		return -ENODEV;
> +#endif
> +	RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops-
> >rx_descriptor_status, -ENOTSUP);
> +	rxq = dev->data->rx_queues[queue_id];
> +
> +	return (*dev->dev_ops->rx_descriptor_status)(rxq, offset); }
> +
> +#define RTE_ETH_TX_DESC_FULL    0 /**< Desc filled for hw, waiting xmit.
> */
> +#define RTE_ETH_TX_DESC_DONE    1 /**< Desc done, packet is
> transmitted. */
> +#define RTE_ETH_TX_DESC_UNAVAIL 2 /**< Desc used by driver or hw. */
> +
> +/**
> + * Check the status of a Tx descriptor in the queue.
> + *
> + * It should be called in a similar context than the Tx function:
> + * - on a dataplane core
> + * - not concurrently on the same queue
> + *
> + * Since it's a dataplane function, no check is performed on port_id
> +and
> + * queue_id. The caller must therefore ensure that the port is enabled
> + * and the queue is configured and running.
> + *
> + * Note: accessing to a random descriptor in the ring may trigger cache
> + * misses and have a performance impact.
> + *
> + * @param port_id
> + *  A valid port identifier of the Ethernet device which.
> + * @param queue_id
> + *  A valid Tx queue identifier on this port.
> + * @param offset
> + *  The offset of the descriptor starting from tail (0 is the place
> +where
> + *  the next packet will be send).
> + *
> + * @return
> + *  - (RTE_ETH_TX_DESC_FULL) Descriptor is being processed by the hw, i.e.
> + *    in the transmit queue.
> + *  - (RTE_ETH_TX_DESC_DONE) Hardware is done with this descriptor, it
> can
> + *    be reused by the driver.
> + *  - (RTE_ETH_TX_DESC_UNAVAIL): Descriptor is unavailable, reserved by
> the
> + *    driver or the hardware.
> + *  - (-EINVAL) bad descriptor offset.
> + *  - (-ENOTSUP) if the device does not support this function.
> + *  - (-ENODEV) bad port or queue (only if compiled with debug).
> + */
> +static inline int rte_eth_tx_descriptor_status(uint8_t port_id,
> +	uint16_t queue_id, uint16_t offset)
> +{
> +	struct rte_eth_dev *dev;
> +	void *txq;
> +
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> +	RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV); #endif
> +	dev = &rte_eth_devices[port_id];
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> +	if (queue_id >= dev->data->nb_tx_queues)
> +		return -ENODEV;
> +#endif
> +	RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops-
> >tx_descriptor_status, -ENOTSUP);
> +	txq = dev->data->tx_queues[queue_id];
> +
> +	return (*dev->dev_ops->tx_descriptor_status)(txq, offset); }
> +
>  /**
>   * Send a burst of output packets on a transmit queue of an Ethernet device.
>   *
> --
> 2.8.1



More information about the dev mailing list