[dpdk-dev] [PATCH v2] net/ixgbe: ensure link status is updated

Olivier Matz olivier.matz at 6wind.com
Thu Mar 30 11:19:59 CEST 2017


Hi,

Can this patch be applied?

Thanks,
Olivier


On Thu, 16 Feb 2017 17:32:01 +0100, Olivier Matz <olivier.matz at 6wind.com> wrote:
> From: Laurent Hardy <laurent.hardy at 6wind.com>
> 
> In case of fiber and link speed set to 1Gb at peer side (with autoneg
> or with defined speed), link status could be not properly updated at
> time cable is plugged-in.
> Indeed if cable was not plugged when device has been configured and
> started then link status will not be updated properly with new speed
> as no link setup will be triggered.
> 
> To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
> setup each time link_update() is triggered and current link status is
> down. When cable is plugged-in, link setup will be performed via
> ixgbe_setup_link().
> 
> Signed-off-by: Laurent Hardy <laurent.hardy at 6wind.com>
> ---
> 
> v1 -> v2:
> - rebase on top of head (change flag to 1<<4)
> - fix regression with copper links: only update link for fiber links
> 
>  drivers/net/ixgbe/ixgbe_ethdev.c | 21 +++++++++++++++++++++
>  drivers/net/ixgbe/ixgbe_ethdev.h |  1 +
>  2 files changed, 22 insertions(+)
> 
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 0b89598..1114106 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -2357,6 +2357,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
>  
>  	/* set flag to update link status after init */
>  	intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
> +	intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
>  
>  	/*
>  	 * Initialize to TRUE. If any of Rx queues doesn't meet the bulk
> @@ -3515,8 +3516,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
>  	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>  	struct rte_eth_link link, old;
>  	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> +	struct ixgbe_interrupt *intr =
> +		IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
>  	int link_up;
>  	int diag;
> +	u32 speed = 0;
> +	bool autoneg = false;
>  
>  	link.link_status = ETH_LINK_DOWN;
>  	link.link_speed = 0;
> @@ -3526,6 +3531,20 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
>  
>  	hw->mac.get_link_status = true;
>  
> +	if ((intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) &&
> +		hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
> +		speed = hw->phy.autoneg_advertised;
> +		if (!speed) {
> +			ixgbe_get_link_capabilities(hw, &speed, &autoneg);
> +			/* setup the highest link when no autoneg */
> +			if (!autoneg) {
> +				if (speed & IXGBE_LINK_SPEED_10GB_FULL)
> +					speed = IXGBE_LINK_SPEED_10GB_FULL;
> +			}
> +		}
> +		ixgbe_setup_link(hw, speed, true);
> +	}
> +
>  	/* check if it needs to wait to complete, if lsc interrupt is enabled */
>  	if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
>  		diag = ixgbe_check_link(hw, &link_speed, &link_up, 0);
> @@ -3543,10 +3562,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
>  
>  	if (link_up == 0) {
>  		rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> +		intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
>  		if (link.link_status == old.link_status)
>  			return -1;
>  		return 0;
>  	}
> +	intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
>  	link.link_status = ETH_LINK_UP;
>  	link.link_duplex = ETH_LINK_FULL_DUPLEX;
>  
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
> index aabbb00..bed4379 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -45,6 +45,7 @@
>  #define IXGBE_FLAG_MAILBOX          (uint32_t)(1 << 1)
>  #define IXGBE_FLAG_PHY_INTERRUPT    (uint32_t)(1 << 2)
>  #define IXGBE_FLAG_MACSEC           (uint32_t)(1 << 3)
> +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 4)
>  
>  /*
>   * Defines that were not part of ixgbe_type.h as they are not used by the



More information about the dev mailing list