[dpdk-dev] [PATCH v2 1/2] net/ixgbe: add and export MDIO APIs

Shweta Choudaha shweta.choudaha at gmail.com
Tue Jan 23 16:12:21 CET 2018


Hi Helin,

   Thanks for the review.
I 'll look at adding test cases  too.
In the meantime, updated this patch to reflect changes in patch 2 of the
series.

Thanks,
Shweta

On Thu, Dec 21, 2017 at 3:25 AM, Zhang, Helin <helin.zhang at intel.com> wrote:

> In general, I'd suggest to add two things together with this patch set.
> 1. test cases in testpmd.
> 2. documentation in release notes, testpmd doc, and others if needed.
>
> Regards,
> Helin
>
> > -----Original Message-----
> > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Shweta Choudaha
> > Sent: Monday, November 6, 2017 10:25 PM
> > To: dev at dpdk.org
> > Cc: Shweta Choudaha
> > Subject: [dpdk-dev] [PATCH v2 1/2] net/ixgbe: add and export MDIO APIs
> >
> > From: Shweta Choudaha <shweta.choudaha at att.com>
> >
> > Add ixgbe MDIO access APIs to read and write PHY registers when being
> used
> > as a backplane port. Export these APIs via the map file
> >
> > Signed-off-by: Shweta Choudaha <shweta.choudaha at att.com>
> > Reviewed-by: Chas Williams <chas3 at att.com>
> > Reviewed-by: Luca Boccassi <bluca at debian.org>
> > ---
> >  drivers/net/ixgbe/rte_pmd_ixgbe.c           | 53
> > +++++++++++++++++++++++++++++
> >  drivers/net/ixgbe/rte_pmd_ixgbe.h           | 39 +++++++++++++++++++++
> >  drivers/net/ixgbe/rte_pmd_ixgbe_version.map |  7 ++++
> >  3 files changed, 99 insertions(+)
> >
> > diff --git a/drivers/net/ixgbe/rte_pmd_ixgbe.c
> > b/drivers/net/ixgbe/rte_pmd_ixgbe.c
> > index f127378..34d8cb4 100644
> > --- a/drivers/net/ixgbe/rte_pmd_ixgbe.c
> > +++ b/drivers/net/ixgbe/rte_pmd_ixgbe.c
> > @@ -1041,3 +1041,56 @@ rte_pmd_ixgbe_bypass_wd_reset(uint16_t
> > port_id)
> >       return ixgbe_bypass_wd_reset(dev);
> >  }
> >  #endif
> > +
> > +static void rte_pmd_ixgbe_get_hw_phy(uint16_t port, struct ixgbe_hw
> > **hw,
> > +                                  struct ixgbe_phy_info **phy)
> > +{
> > +     struct rte_eth_dev *dev;
> > +
> > +     *hw = NULL;
> > +     *phy = NULL;
> > +
> > +     dev = &rte_eth_devices[port];
> > +     if (!is_ixgbe_supported(dev))
> > +             return;
> > +
> > +     *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> > +     if (!*hw)
> > +             return;
> > +
> > +     *phy = &(*hw)->phy;
> > +}
> > +
> > +int
> > +rte_pmd_ixgbe_mdio_read(uint16_t port, uint32_t reg_addr,
> > +                     uint32_t dev_type, uint16_t *phy_data) {
> > +     struct ixgbe_hw *hw;
> > +     struct ixgbe_phy_info *phy;
> > +
> > +     RTE_ETH_VALID_PORTID_OR_ERR_RET(port, -ENODEV);
> > +
> > +     rte_pmd_ixgbe_get_hw_phy(port, &hw, &phy);
> > +
> > +     if (!hw || !phy)
> > +             return -ENOTSUP;
> > +
> > +     return phy->ops.read_reg_mdi(hw, reg_addr, dev_type, phy_data); }
> > +
> > +int
> > +rte_pmd_ixgbe_mdio_write(uint16_t port, uint32_t reg_addr,
> > +                      uint32_t dev_type, uint16_t phy_data) {
> > +     struct ixgbe_hw *hw;
> > +     struct ixgbe_phy_info *phy;
> > +
> > +     RTE_ETH_VALID_PORTID_OR_ERR_RET(port, -ENODEV);
> > +
> > +     rte_pmd_ixgbe_get_hw_phy(port, &hw, &phy);
> > +
> > +     if (!hw || !phy)
> > +             return -ENOTSUP;
> > +
> > +     return phy->ops.write_reg_mdi(hw, reg_addr, dev_type, phy_data); }
> > diff --git a/drivers/net/ixgbe/rte_pmd_ixgbe.h
> > b/drivers/net/ixgbe/rte_pmd_ixgbe.h
> > index 81b18f8..5d36f8a 100644
> > --- a/drivers/net/ixgbe/rte_pmd_ixgbe.h
> > +++ b/drivers/net/ixgbe/rte_pmd_ixgbe.h
> > @@ -601,6 +601,45 @@ int
> > rte_pmd_ixgbe_bypass_wd_timeout_show(uint16_t port, uint32_t
> > *wd_timeout);
> >   */
> >  int rte_pmd_ixgbe_bypass_wd_reset(uint16_t port);
> >
> > +/**
> > + * Read PHY register using MDIO
> > + *
> > + * @param port
> > + *   The port identifier of the Ethernet device.
> > + * @param reg_addr
> > + *   32 bit PHY Register
> > + * @param dev_type
> > + *   Always Unused
> > + * @param phy_data
> > + *   Pointer for reading PHY register data
> > + * @return
> > + *   - (0) if successful.
> > + *   - (-ENOTSUP) if hardware doesn't support.
> > + *   - (-ENODEV) if *port* invalid.
> > + */
> > +int
> > +rte_pmd_ixgbe_mdio_read(uint16_t port, uint32_t reg_addr,
> > +                     uint32_t dev_type, uint16_t *phy_data);
> > +
> > +/**
> > + * Write data to PHY register using MDIO
> > + *
> > + * @param port
> > + *   The port identifier of the Ethernet device.
> > + * @param reg_addr
> > + *   32 bit PHY Register
> > + * @param dev_type
> > + *   Always unused
> > + * @param phy_data
> > + *   Data to write to PHY register
> > + * @return
> > + *   - (0) if successful.
> > + *   - (-ENOTSUP) if hardware doesn't support.
> > + *   - (-ENODEV) if *port* invalid.
> > + */
> > +int
> > +rte_pmd_ixgbe_mdio_write(uint16_t port, uint32_t reg_addr,
> > +                      uint32_t dev_type, uint16_t phy_data);
> >
> >  /**
> >   * Response sent back to ixgbe driver from user app after callback diff
> --git
> > a/drivers/net/ixgbe/rte_pmd_ixgbe_version.map
> > b/drivers/net/ixgbe/rte_pmd_ixgbe_version.map
> > index bf77674..ce72c73 100644
> > --- a/drivers/net/ixgbe/rte_pmd_ixgbe_version.map
> > +++ b/drivers/net/ixgbe/rte_pmd_ixgbe_version.map
> > @@ -52,3 +52,10 @@ DPDK_17.08 {
> >       rte_pmd_ixgbe_bypass_wd_timeout_show;
> >       rte_pmd_ixgbe_bypass_wd_timeout_store;
> >  } DPDK_17.05;
> > +
> > +EXPERIMENTAL {
> > +     global:
> > +
> > +     rte_pmd_ixgbe_mdio_read;
> > +     rte_pmd_ixgbe_mdio_write;
> > +} DPDK_17.08;
> > --
> > 2.1.4
>
>


More information about the dev mailing list