[dpdk-dev] [PATCH] net/nfp: add CPP bridge as service

Alejandro Lucero alejandro.lucero at netronome.com
Wed Jan 9 15:20:38 CET 2019


On Wed, Jan 9, 2019 at 10:54 AM Ferruh Yigit <ferruh.yigit at intel.com> wrote:

> On 1/3/2019 8:56 AM, Alejandro Lucero wrote:
> > The Netronome's Network Flow Processor chip is highly programmable
> > with the goal of processing packets at high speed. Processing units
> > and other chip components are available from the host through the
> > PCIe CPP(Command Push Pull bus) interface. The NFP PF PMD configures
> > a CPP handler for setting up and working with vNICs, perform actions
> > like link up or down, or accessing extended stats from the MAC component.
> >
> > There exist NFP host tools which access the NFP components for
> > programming and debugging but they require the CPP interface. When the
> > PMD is bound to the PF, the DPDK app owns the CPP interface, so these
> > host tools can not access the NFP through other means like NFP kernel
> > drivers.
> >
> > This patch adds a CPP bridge using the rte_service API which can be
> > enabled by a DPDK app. Interestingly, DPDK clients like OVS will not
> > enable specific service cores, but this can be performed with a
> > secondary process specifically enabling this CPP bridge service and
> > therefore giving access to the NFP to those host tools.
>
> Hi Alejandro,
>
>
Hi Ferruh,


> Getting a few build errors, more details below.
>
> >
> > Signed-off-by: Alejandro Lucero <alejandro.lucero at netronome.com>
> <...>
>
> > +     /* Obtain target's CPP ID and offset in target */
> > +     cpp_id = (offset >> 40) << 8;
>
> With icc, i686 getting [1], it seems 'off_t' is 32bits long on 32bit build.
>
> [1]
> error #63: shift count is too large
>
>
We do not support 32 bits. I thought our PMD was not built in that case.


> <...>
>
> > +                     if (err != (int)len) {
> > +                             printf("%s: error when receiving, %d of
> %lu\n",
> > +                                     __func__, err, count);
>
> Giving build error for 32bits [3], and can you please use logging macros
> instead
> of printf?
>
>
Sure.


> [3]
> error: format ‘%lu’ expects argument of type ‘long unsigned int’, but
> argument 4
> has type ‘size_t’ {aka ‘unsigned int’} [-Werror=format=]
>
<...>
>
> > +     /* Obtain target's CPP ID and offset in target */
> > +     cpp_id = (offset >> 40) << 8;
>
> Same as above [1].
>
> <...>
>
> > +                     if (err != (int)len) {
> > +                             printf("%s: error when sending: %d of
> %lu\n",
> > +                                     __func__, err, count);
>
> Same build error with above [3].
>
> <...>
>
> > +nfp_cpp_bridge_serve_ioctl(int sockfd, struct nfp_cpp *cpp)
> > +{
> > +     int cmd, err;
> > +     uint32_t ident_size, tmp;
> > +
> > +     /* Reading now the IOCTL command */
> > +     err = recv(sockfd, &cmd, 4, 0);
> > +     if (err != 4) {
> > +             printf("%s: read error from socket\n", __func__);
> > +             return -EIO;
> > +     }
> > +
> > +     /* Only supporting NFP_IOCTL_CPP_IDENTIFICATION */
> > +     if (cmd != NFP_IOCTL_CPP_IDENTIFICATION) {
>
> Giving build error with ppc_64-power8-linuxapp-gcc [2].
>
>
We do not support power architecture.


> [2]
> error: comparison is always true due to limited range of data type
> [-Werror=type-limits]
>


More information about the dev mailing list