[dpdk-dev] [v3] net/virtio: set offload flag for jumbo frames

Ilya Maximets i.maximets at samsung.com
Thu Jan 31 12:01:53 CET 2019


On 31.01.2019 12:17, Jens Freimann wrote:
> Port configuration fails because offload flags don't match the expected
> value when max-pkt-len is set to a value that should enable receive port
> offloading but doesn't.
> 
> There are two cases to consider:
> 
> 1. VIRTIO_NET_F_MTU is set. Then we need to check if the requested
>    max-pkt-len fits into the MTU plus header. If yes we set the
>    offload flag.
> 2. VIRTIO_NET_F_MTU is not set. We can set the offload flag.
> 
> Fixes: a4996bd89c42 ("ethdev: new Rx/Tx offloads API")
> Cc: stable at dpdk.org
> 
> Signed-off-by: Jens Freimann <jfreimann at redhat.com>
> Reviewed-by: Maxime Coquelin <maxime.coquelin at redhat.com>
> ---
> v2->v3:
>  * remove unnecessary brackets (Maxime)
>  * fix commit message (David)
> 
> v1->v2:
>  * include virtnet hdr, ethernet header, vlan tag when comparing against
>    max-rx-pkt-len (Maxime)
> 
>  drivers/net/virtio/virtio_ethdev.c | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/drivers/net/virtio/virtio_ethdev.c b/drivers/net/virtio/virtio_ethdev.c
> index 7c4c1df00..f39d4e630 100644
> --- a/drivers/net/virtio/virtio_ethdev.c
> +++ b/drivers/net/virtio/virtio_ethdev.c
> @@ -2351,6 +2351,20 @@ virtio_dev_info_get(struct rte_eth_dev *dev, struct rte_eth_dev_info *dev_info)
>  	if ((host_features & tso_mask) == tso_mask)
>  		dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
>  
> +	if (host_features & (1ULL << VIRTIO_NET_F_MTU)) {
> +		struct virtio_net_config config;
> +		uint32_t ether_hdr_len = ETHER_HDR_LEN + VLAN_TAG_LEN +
> +			hw->vtnet_hdr_size;
> +		vtpci_read_dev_config(hw,
> +				offsetof(struct virtio_net_config, mtu),
> +				&config.mtu, sizeof(config.mtu));
> +		if (dev->data->dev_conf.rxmode.max_rx_pkt_len <=
> +				config.mtu + ether_hdr_len)
> +			dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_JUMBO_FRAME;
> +	} else {
> +		dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_JUMBO_FRAME;
> +	}
> +

Why we can't just use 'hw->max_mtu' here for checking instead of
reading 'config.mtu' ?
Also, It's already calculated with regards to VIRTIO_NET_F_MTU.


>  	dev_info->tx_offload_capa = DEV_TX_OFFLOAD_MULTI_SEGS |
>  				    DEV_TX_OFFLOAD_VLAN_INSERT;
>  	if (host_features & (1ULL << VIRTIO_NET_F_CSUM)) {
> 


More information about the dev mailing list