[dpdk-dev] [External] RE: mlx5: the default rule makes VF rep cannot get packets

[贺鹏]

Hi,


I see.

I am going to try OFED 4.7 official version and see if it works. 

Thanks.

> 在 2019年11月25日，下午4:28，Slava Ovsiienko <viacheslavo at mellanox.com> 写道：
> 
> Hi,
>  
> please, see below.
>  
> From: 贺鹏 <hepeng.0320 at bytedance.com <mailto:hepeng.0320 at bytedance.com>> 
> Sent: Monday, November 25, 2019 9:44
> To: Slava Ovsiienko <viacheslavo at mellanox.com <mailto:viacheslavo at mellanox.com>>
> Cc: dev at dpdk.org <mailto:dev at dpdk.org>; Matan Azrad <matan at mellanox.com <mailto:matan at mellanox.com>>
> Subject: Re: [External] RE: mlx5: the default rule makes VF rep cannot get packets
>  
> Hi, 
> 在 2019年11月25日，下午3:32，Slava Ovsiienko <viacheslavo at mellanox.com <mailto:viacheslavo at mellanox.com>> 写道：
>  
> Hi,
> What OFED version do you use? Or OOB kernel driver/rdma-core?
> OFED 4.6-3.11.
> 
> 
> Target table (1 in the mentioned patch) is created on the flow creation as empty one.
> The default rule for the empty ingress table in FDB (transfer attribute in testpmd command)
> – go to vport 0 (to wire/VF representors), it is established by kernel/rdma-core, In your setup
> it does not work.
>  
>  
> The NIC works in switchdev mode; every VF has a representer, and dpdk is polling each rep to get packets. 
> If I revert this patch, in the probe stage, DPDK will not install the default rule which directs packets to Table 1, and dpdk can get packets.
>  
> The target is to use dpdk as well as action offload together.  
>  
> The setup code is in the function  *mlx5_flow_create_esw_table_zero_flow*.
> Even for running L2FWD, I cannot get a packet from VF rep.  You mean this is a driver problem ?
>  
> I think so. If there is no any DPDK rule in Table 0, everything works OK, right?
> It means the default rule (hidden from DPDK) in table 0 works, and packets go to the vport 0
> (contains all representors). If we insert jump to table 1 – nothing works, it means the default
> rule in table 1 fails. This one is not established by DPDK, but by the driver.
>  
> With best regards, Slava
>  
>  
>  
> 
> 
> With best regards, Slava
>  
> From: 贺鹏 <hepeng.0320 at bytedance.com <mailto:hepeng.0320 at bytedance.com>> 
> Sent: Monday, November 25, 2019 9:27
> To: dev at dpdk.org <mailto:dev at dpdk.org>; Matan Azrad <matan at mellanox.com <mailto:matan at mellanox.com>>; Slava Ovsiienko <viacheslavo at mellanox.com <mailto:viacheslavo at mellanox.com>>
> Subject: mlx5: the default rule makes VF rep cannot get packets
>  
> Hi, 
>  
> We found the patch "net/mlx5: revert default rules amount optimization", 
> which installs a rule directing all egress traffic from VF to table 1, results in 
> VF representors get no packets, even if there is no offload rules installed. 
> 
> 
> 
> I’ve tested both l2fwd and ovs-dpdk.  However, PF rep works just fine. 
>  
>  
> We are using dpdk 19.11-rc3 for evaluation.
>