[dpdk-dev] [PATCH 4/4] net/hns3: fix FEC state query

oulijun oulijun at huawei.com
Mon Dec 7 15:50:41 CET 2020



在 2020/11/20 22:33, Ferruh Yigit 写道:
> On 11/20/2020 11:27 AM, Lijun Ou wrote:
>> From: "Min Hu (Conor)" <humin29 at huawei.com>
>>
>> As FEC is not supported below 10 Gbps, CMD(0x031A) offered
>> from Firmware read will return fail in 10 Gbps device.
>>
>> This patch will prevent read this CMD when below 10 Gbps,
>> as this is non-sense.
>>
>> Fixes: 9bf2ea8dbc65 ("net/hns3: support FEC")
>> Cc: stable at dpdk.org
>>
>> Signed-off-by: Min Hu (Connor) <humin29 at huawei.com>
>> Signed-off-by: Lijun Ou <oulijun at huawei.com>
>> ---
>>   drivers/net/hns3/hns3_ethdev.c | 38 
>> ++++++++++++++++++++++++--------------
>>   1 file changed, 24 insertions(+), 14 deletions(-)
>>
>> diff --git a/drivers/net/hns3/hns3_ethdev.c 
>> b/drivers/net/hns3/hns3_ethdev.c
>> index d6d3f03..faa7b0a 100644
>> --- a/drivers/net/hns3/hns3_ethdev.c
>> +++ b/drivers/net/hns3/hns3_ethdev.c
>> @@ -100,7 +100,7 @@ static int hns3_add_mc_addr(struct hns3_hw *hw,
>>   static int hns3_remove_mc_addr(struct hns3_hw *hw,
>>                   struct rte_ether_addr *mac_addr);
>>   static int hns3_restore_fec(struct hns3_hw *hw);
>> -static int hns3_query_dev_fec_info(struct rte_eth_dev *dev);
>> +static int hns3_query_dev_fec_info(struct hns3_hw *hw);
>>   void hns3_ether_format_addr(char *buf, uint16_t size,
>>                   const struct rte_ether_addr *ether_addr)
>> @@ -3010,13 +3010,6 @@ hns3_get_capability(struct hns3_hw *hw)
>>           device_id == HNS3_DEV_ID_200G_RDMA)
>>           hns3_set_bit(hw->capability, HNS3_DEV_SUPPORT_DCB_B, 1);
>> -    ret = hns3_query_dev_fec_info(eth_dev);
>> -    if (ret) {
>> -        PMD_INIT_LOG(ERR,
>> -                 "failed to query FEC information, ret = %d", ret);
>> -        return ret;
>> -    }
>> -
>>       /* Get PCI revision id */
>>       ret = rte_pci_read_config(pci_dev, &revision, 
>> HNS3_PCI_REVISION_ID_LEN,
>>                     HNS3_PCI_REVISION_ID);
>> @@ -3148,8 +3141,15 @@ hns3_get_configuration(struct hns3_hw *hw)
>>       }
>>       ret = hns3_get_board_configuration(hw);
>> -    if (ret)
>> +    if (ret) {
>>           PMD_INIT_LOG(ERR, "failed to get board configuration: %d", 
>> ret);
>> +        return ret;
>> +    }
>> +
>> +    ret = hns3_query_dev_fec_info(hw);
>> +    if (ret)
>> +        PMD_INIT_LOG(ERR,
>> +                 "failed to query FEC information, ret = %d", ret);
>>       return ret;
>>   }
>> @@ -5797,6 +5797,15 @@ get_current_fec_auto_state(struct hns3_hw *hw, 
>> uint8_t *state)
>>       struct hns3_cmd_desc desc;
>>       int ret;
>> +    /*
>> +     * CMD(0x031A) read is not supported in device of link speed
>> +     * below 10 Gbps.
>> +     */
>> +    if (hw->mac.link_speed < ETH_SPEED_NUM_10G) {
>> +        *state = 0;
>> +        return 0;
>> +    }
>> +
>>       hns3_cmd_setup_basic_desc(&desc, HNS3_OPC_CONFIG_FEC_MODE, true);
>>       req = (struct hns3_config_fec_cmd *)desc.data;
>>       ret = hns3_cmd_send(hw, &desc, 1);
>> @@ -6003,14 +6012,15 @@ hns3_restore_fec(struct hns3_hw *hw)
>>   }
>>   static int
>> -hns3_query_dev_fec_info(struct rte_eth_dev *dev)
>> +hns3_query_dev_fec_info(struct hns3_hw *hw)
>>   {
>> -    struct hns3_adapter *hns = dev->data->dev_private;
>> -    struct hns3_hw *hw = HNS3_DEV_PRIVATE_TO_HW(hns);
>> -    struct hns3_pf *pf = &hns->pf;
>> +    struct hns3_adapter *hns = HNS3_DEV_HW_TO_ADAPTER(hw);
>> +    struct hns3_pf *pf = HNS3_DEV_PRIVATE_TO_PF(hns);
>> +    struct rte_eth_dev *eth_dev;
>>       int ret;
>> -    ret = hns3_fec_get(dev, &pf->fec_mode);
>> +    eth_dev = &rte_eth_devices[hw->data->port_id];
> 
> Not specific to this patch, but it is not good idea to access global 
> 'rte_eth_devices' array directly. Why not store the 'eth_dev' in the 
> device private data in the probe() and use it later?
> Can you do a separate patch for this switch?
> Thank you may not need to change the paramters of the 
> 'hns3_query_dev_fec_info()' or remove it from 
> 'hns3_query_dev_fec_info()' since you will be able to access to 
> 'eth_dev' easily.
Thanks. Your suggestion looks very good to me. I will fixes it in the 
release cycle.
> 
>> +    ret = hns3_fec_get(eth_dev, &pf->fec_mode);
>>       if (ret)
>>           hns3_err(hw, "query device FEC info failed, ret = %d", ret);
>>
> 
> .
> 


More information about the dev mailing list