[dpdk-dev] [PATCH 2/2] net/qede: restore Tx queue setup

[Jerin Jacob]

On Tue, May 5, 2020 at 8:39 AM Rasesh Mody <rmody at marvell.com> wrote:
>
> Some applications do not explicitly restore Tx queues setup during
> port re-configuration. This patch adds changes to check for
> released Tx queues and restore the setup if application doesn't
> explicitly does that.

+ethdev maintainers.

I think, Ideally, the fix should be in common code if we need to
support such applications.

This would avoid the following case
- The application works only on a specific PMD.
- every PMD duplicating such restoration code.


>
> Signed-off-by: Rasesh Mody <rmody at marvell.com>
> Signed-off-by: Igor Russkikh <irusskikh at marvell.com>
> ---
>  drivers/net/qede/qede_ethdev.h |  3 +++
>  drivers/net/qede/qede_rxtx.c   | 25 ++++++++++++++++++++++++-
>  2 files changed, 27 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/qede/qede_ethdev.h b/drivers/net/qede/qede_ethdev.h
> index b988a73f2..2e8e5febc 100644
> --- a/drivers/net/qede/qede_ethdev.h
> +++ b/drivers/net/qede/qede_ethdev.h
> @@ -235,6 +235,9 @@ struct qede_dev {
>         bool enable_lro;
>         uint8_t num_rx_queues;
>         uint8_t num_tx_queues;
> +       uint16_t num_rx_desc;
> +       uint16_t num_tx_desc;
> +       const struct rte_eth_txconf *tx_conf;
>         SLIST_HEAD(vlan_list_head, qede_vlan_entry)vlan_list_head;
>         uint16_t configured_vlans;
>         bool accept_any_vlan;
> diff --git a/drivers/net/qede/qede_rxtx.c b/drivers/net/qede/qede_rxtx.c
> index b81788ca4..1b212a4fb 100644
> --- a/drivers/net/qede/qede_rxtx.c
> +++ b/drivers/net/qede/qede_rxtx.c
> @@ -151,6 +151,7 @@ qede_alloc_rx_queue_mem(struct rte_eth_dev *dev,
>         rxq->qdev = qdev;
>         rxq->mb_pool = mp;
>         rxq->nb_rx_desc = nb_desc;
> +       qdev->num_rx_desc = rxq->nb_rx_desc;
>         rxq->queue_id = queue_idx;
>         rxq->port_id = dev->data->port_id;
>
> @@ -405,6 +406,7 @@ qede_alloc_tx_queue_mem(struct rte_eth_dev *dev,
>         }
>
>         txq->nb_tx_desc = nb_desc;
> +       qdev->num_tx_desc = txq->nb_tx_desc;
>         txq->qdev = qdev;
>         txq->port_id = dev->data->port_id;
>
> @@ -443,6 +445,7 @@ qede_alloc_tx_queue_mem(struct rte_eth_dev *dev,
>
>         txq->nb_tx_avail = txq->nb_tx_desc;
>
> +       qdev->tx_conf = tx_conf;
>         txq->tx_free_thresh =
>             tx_conf->tx_free_thresh ? tx_conf->tx_free_thresh :
>             (txq->nb_tx_desc - QEDE_DEFAULT_TX_FREE_THRESH);
> @@ -593,7 +596,7 @@ qede_alloc_mem_sb(struct qede_dev *qdev, struct ecore_sb_info *sb_info,
>
>  int qede_alloc_fp_resc(struct qede_dev *qdev)
>  {
> -       struct ecore_dev *edev = &qdev->edev;
> +       struct ecore_dev *edev = QEDE_INIT_EDEV(qdev);
>         struct qede_fastpath *fp;
>         uint32_t num_sbs;
>         uint16_t sb_idx;
> @@ -1005,9 +1008,29 @@ static int qede_tx_queue_stop(struct rte_eth_dev *eth_dev, uint16_t tx_queue_id)
>  int qede_start_queues(struct rte_eth_dev *eth_dev)
>  {
>         struct qede_dev *qdev = QEDE_INIT_QDEV(eth_dev);
> +       struct ecore_dev *edev = QEDE_INIT_EDEV(qdev);
> +       struct qede_tx_queue *txq;
> +       struct qede_fastpath *fp;
>         uint8_t id;
>         int rc = -1;
>
> +       /* Restore setup of Tx queues */
> +       for (id = 0; id < qdev->num_tx_queues; id++) {
> +               fp = &qdev->fp_array[id];
> +               txq = fp->txq;
> +
> +               if (!txq) {
> +                       rc = qede_tx_queue_setup(eth_dev, id, qdev->num_tx_desc,
> +                                                eth_dev->data->numa_node,
> +                                                qdev->tx_conf);
> +                       if (rc != ECORE_SUCCESS) {
> +                               DP_ERR(edev, "TX queue %u not setup rc=%d\n",
> +                                      id, rc);
> +                               return -1;
> +                       }
> +               }
> +       }
> +
>         for (id = 0; id < qdev->num_rx_queues; id++) {
>                 rc = qede_rx_queue_start(eth_dev, id);
>                 if (rc != ECORE_SUCCESS)
> --
> 2.18.0
>