[dpdk-dev] [PATCH 4/4] app/testpmd: change hairpin queues setup

Bing Zhao bingz at nvidia.com
Thu Oct 1 02:26:02 CEST 2020


A new parameter `hairpin-mode` is introduced to the testpmd command
line. Bitmask value is used to provide more flexible configuration.

Bit 0 in the LSB indicates the hairpin will use the loop mode. The
previous port RX queue will be connected to the current port TX
queue.
Bit 1 in the LSB indicates the hairpin will use pair port mode. The
even index port will be paired with the next odd index port. If the
total number of probed port is odd, then the last one will be paired
to itself.
If this byte is zero, then each port will be paired to itself.
Bit 0 takes a higher priority in the checking.

Bit 4 in the second bytes indicate if the hairpin will use explicit
TX flow mode.

If not set, default value zero will be used and the behavior will
try to get align with the previous single port mode. If the ports
belong to different vendors' NICs, it is suggested to use the `self`
hairpin mode only.

Since hairpin configures the hardware resources, the port mask of
packets forwarding engine will not be used here.

Signed-off-by: Bing Zhao <bingz at nvidia.com>
---
 app/test-pmd/parameters.c | 15 +++++++++++
 app/test-pmd/testpmd.c    | 68 ++++++++++++++++++++++++++++++++++++++++++++---
 app/test-pmd/testpmd.h    |  2 ++
 3 files changed, 81 insertions(+), 4 deletions(-)

diff --git a/app/test-pmd/parameters.c b/app/test-pmd/parameters.c
index 1ead595..991029d 100644
--- a/app/test-pmd/parameters.c
+++ b/app/test-pmd/parameters.c
@@ -221,6 +221,9 @@ usage(char* progname)
 	       "enabled\n");
 	printf("  --record-core-cycles: enable measurement of CPU cycles.\n");
 	printf("  --record-burst-stats: enable display of RX and TX bursts.\n");
+	printf("  --hairpin-mode=0xXX: bitmask set the hairpin port mode.\n "
+	       "    0x10 - explicit tx rule, 0x02 - hairpin ports paired\n"
+	       "    0x01 - hairpin ports loop, 0x00 - hairpin port self\n");
 }
 
 #ifdef RTE_LIBRTE_CMDLINE
@@ -644,6 +647,7 @@ launch_args_parse(int argc, char** argv)
 		{ "rxd",			1, 0, 0 },
 		{ "txd",			1, 0, 0 },
 		{ "hairpinq",			1, 0, 0 },
+		{ "hairpin-mode",		1, 0, 0 },
 		{ "burst",			1, 0, 0 },
 		{ "mbcache",			1, 0, 0 },
 		{ "txpt",			1, 0, 0 },
@@ -1111,6 +1115,17 @@ launch_args_parse(int argc, char** argv)
 				rte_exit(EXIT_FAILURE, "Either rx or tx queues should "
 						"be non-zero\n");
 			}
+			if (!strcmp(lgopts[opt_idx].name, "hairpin-mode")) {
+				char *end = NULL;
+				unsigned int n;
+
+				errno = 0;
+				n = strtoul(optarg, &end, 0);
+				if (errno != 0 || end == optarg)
+					rte_exit(EXIT_FAILURE, "hairpin mode invalid\n");
+				else
+					hairpin_mode = (uint16_t)n;
+			}
 			if (!strcmp(lgopts[opt_idx].name, "burst")) {
 				n = atoi(optarg);
 				if (n == 0) {
diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c
index fe6450c..c604045 100644
--- a/app/test-pmd/testpmd.c
+++ b/app/test-pmd/testpmd.c
@@ -367,6 +367,9 @@ bool setup_on_probe_event = true;
 /* Clear ptypes on port initialization. */
 uint8_t clear_ptypes = true;
 
+/* Hairpin ports configuration mode. */
+uint16_t hairpin_mode;
+
 /* Pretty printing of ethdev events */
 static const char * const eth_event_desc[] = {
 	[RTE_ETH_EVENT_UNKNOWN] = "unknown",
@@ -2345,7 +2348,7 @@ port_is_started(portid_t port_id)
 
 /* Configure the Rx and Tx hairpin queues for the selected port. */
 static int
-setup_hairpin_queues(portid_t pi)
+setup_hairpin_queues(portid_t pi, portid_t p_pi, uint16_t cnt_pi)
 {
 	queueid_t qi;
 	struct rte_eth_hairpin_conf hairpin_conf = {
@@ -2354,10 +2357,48 @@ setup_hairpin_queues(portid_t pi)
 	int i;
 	int diag;
 	struct rte_port *port = &ports[pi];
+	uint16_t peer_rx_port = pi;
+	uint16_t peer_tx_port = pi;
+	uint32_t manual = 1;
+	uint32_t tx_exp = hairpin_mode & 0x10;
+
+	if (!(hairpin_mode & 0xf)) {
+		peer_rx_port = pi;
+		peer_tx_port = pi;
+		manual = 0;
+	} else if (hairpin_mode & 0x1) {
+		peer_tx_port = rte_eth_find_next_owned_by(pi + 1,
+						       RTE_ETH_DEV_NO_OWNER);
+		if (peer_tx_port >= RTE_MAX_ETHPORTS)
+			peer_tx_port = rte_eth_find_next_owned_by(0,
+						RTE_ETH_DEV_NO_OWNER);
+		if (p_pi != RTE_MAX_ETHPORTS) {
+			peer_rx_port = p_pi;
+		} else {
+			uint16_t next_pi;
+
+			RTE_ETH_FOREACH_DEV(next_pi)
+				peer_rx_port = next_pi;
+		}
+		manual = 1;
+	} else if (hairpin_mode & 0x2) {
+		if (cnt_pi & 0x1) {
+			peer_rx_port = p_pi;
+		} else {
+			peer_rx_port = rte_eth_find_next_owned_by(pi + 1,
+						RTE_ETH_DEV_NO_OWNER);
+			if (peer_rx_port >= RTE_MAX_ETHPORTS)
+				peer_rx_port = pi;
+		}
+		peer_tx_port = peer_rx_port;
+		manual = 1;
+	}
 
 	for (qi = nb_txq, i = 0; qi < nb_hairpinq + nb_txq; qi++) {
-		hairpin_conf.peers[0].port = pi;
+		hairpin_conf.peers[0].port = peer_rx_port;
 		hairpin_conf.peers[0].queue = i + nb_rxq;
+		hairpin_conf.manual_bind = !!manual;
+		hairpin_conf.tx_explicit = !!tx_exp;
 		diag = rte_eth_tx_hairpin_queue_setup
 			(pi, qi, nb_txd, &hairpin_conf);
 		i++;
@@ -2377,8 +2418,10 @@ setup_hairpin_queues(portid_t pi)
 		return -1;
 	}
 	for (qi = nb_rxq, i = 0; qi < nb_hairpinq + nb_rxq; qi++) {
-		hairpin_conf.peers[0].port = pi;
+		hairpin_conf.peers[0].port = peer_tx_port;
 		hairpin_conf.peers[0].queue = i + nb_txq;
+		hairpin_conf.manual_bind = !!manual;
+		hairpin_conf.tx_explicit = !!tx_exp;
 		diag = rte_eth_rx_hairpin_queue_setup
 			(pi, qi, nb_rxd, &hairpin_conf);
 		i++;
@@ -2405,6 +2448,8 @@ start_port(portid_t pid)
 {
 	int diag, need_check_link_status = -1;
 	portid_t pi;
+	portid_t p_pi = RTE_MAX_ETHPORTS;
+	uint16_t cnt_pi = 0;
 	queueid_t qi;
 	struct rte_port *port;
 	struct rte_ether_addr mac_addr;
@@ -2544,8 +2589,10 @@ start_port(portid_t pid)
 				return -1;
 			}
 			/* setup hairpin queues */
-			if (setup_hairpin_queues(pi) != 0)
+			if (setup_hairpin_queues(pi, p_pi, cnt_pi) != 0)
 				return -1;
+			p_pi = pi;
+			cnt_pi++;
 		}
 		configure_rxtx_dump_callbacks(verbose_level);
 		if (clear_ptypes) {
@@ -3775,6 +3822,19 @@ main(int argc, char** argv)
 		rte_exit(EXIT_FAILURE, "Start ports failed\n");
 
 	/* set all ports to promiscuous mode by default */
+	if (hairpin_mode & 0x3) {
+		RTE_ETH_FOREACH_DEV(port_id) {
+			ret = rte_eth_hairpin_bind(port_id, RTE_MAX_ETHPORTS);
+			if (ret != 0) {
+				RTE_LOG(ERR, EAL, "Error during binding "
+					"hairpin tx port %u: %s",
+					port_id, rte_strerror(-ret));
+				return -1;
+			}
+		}
+	}
+
+	/* set all ports to promiscuous mode by default */
 	RTE_ETH_FOREACH_DEV(port_id) {
 		ret = rte_eth_promiscuous_enable(port_id);
 		if (ret != 0)
diff --git a/app/test-pmd/testpmd.h b/app/test-pmd/testpmd.h
index c7e7e41..29ede20 100644
--- a/app/test-pmd/testpmd.h
+++ b/app/test-pmd/testpmd.h
@@ -398,6 +398,8 @@ extern uint32_t param_total_num_mbufs;
 
 extern uint16_t stats_period;
 
+extern uint16_t hairpin_mode;
+
 #ifdef RTE_LIBRTE_LATENCY_STATS
 extern uint8_t latencystats_enabled;
 extern lcoreid_t latencystats_lcore_id;
-- 
2.5.5



More information about the dev mailing list