[PATCH v6 00/15] Wangxun fixes and new features

[Zaiyu Wang]

This series addresses link-related issues on Wangxun Amber-lite 25G/40G NICs
(CR/KR training, hot-plug, 10G link state).

---
v6:
 - fix the apply failure.
---
v5:
 - drop the UDP tunnel patch: the generic UDP tunnel flag covers any UDP
   tunnel, so the tunnel type cannot be resolved from the destination port.
 - P02: advertise 10G, 25G, and 40G from the requested speed mask instead
        of the device ID, so the 25G and 40G parts advertise 10G by
        default as well.
 - P07: keep the patch limited to decoding the 10G link speed from PORTSTAT;
        the AML40 default 10G|40G advertisement change is now in P02.
 - P09: gate the SFP detection alarm and the AN73 watchdog on a new per-port
        flag that dev_stop clears before the first cancel.
        cancel SFP detection before the watchdog.
 - P10: re-arm the 40G module poll only while the SFP/AN73 alarm flag is set.
 - P12: treat the ffe_pre2 and bp_capa devargs as a feature rather than a fix;
        drop the Fixes tags and stable Cc, and document the 25G/40G Amber-Lite
        FFE defaults.
 - P14: bound the AN page exchange, propagate its timeout to the watchdog h
        andler, and avoid register reads used only by disabled BP debug logs.
 - P15: stop clearing the auto_neg devarg when a 10G-only DAC disables AN;
        derive the effective AN73 state from the current module capabilities
        instead. Classify 40G active cables through the optical path, unify
        DAC checks on txgbe_is_dac_cable().

Not handled in this revision:

 - P12: bp_capa is not range-checked. Devarg validation will be added in a
        separate change so all txgbe devargs can be handled consistently.
 - P14: the AN page exchange still busy-waits on the alarm thread and can
        delay handling for other ports. A later change will decouple negotiation
        from the alarm callback and run per-port negotiations in parallel.
---


Zaiyu Wang (15):
  net/txgbe: fix failure to configure 10G on dual-speed DAC
  net/txgbe: use the requested speed in E56 AN setup
  net/txgbe: fix e56 PHY configuration error
  net/txgbe: fix incorrect link state in 10G forced mode
  net/txgbe: do not force reconfig on link retry
  net/txgbe: set i2c sda hold time
  net/txgbe: fix link speed display info for 10G mode
  net/txgbe: remove stale outer UDP checksum offload flag
  net/txgbe: fix SFP hot-plug when auto-negotiation is on
  net/txgbe: fix DAC hot-plug on 40G NIC with auto-negotiation
  net/txgbe: fix 40G FFE tuning applied to first lane only
  net/txgbe: add pre2 FFE tap and backplane capability devargs
  net/txgbe: add devarg to turn off Tx laser for 40G NIC
  net/txgbe: fix CR/KR link training and recovery
  net/txgbe: align link capabilities and DAC classification

 doc/guides/nics/txgbe.rst              |  25 +++-
 doc/guides/rel_notes/release_26_11.rst |  11 ++
 drivers/net/txgbe/base/txgbe_aml.c     |   4 +-
 drivers/net/txgbe/base/txgbe_aml40.c   |  92 ++++++++++--
 drivers/net/txgbe/base/txgbe_e56.c     |  14 +-
 drivers/net/txgbe/base/txgbe_e56.h     |   6 +
 drivers/net/txgbe/base/txgbe_e56_bp.c  | 196 +++++++++++++++----------
 drivers/net/txgbe/base/txgbe_e56_bp.h  |   4 +-
 drivers/net/txgbe/base/txgbe_hw.c      |  33 +++++
 drivers/net/txgbe/base/txgbe_osdep.h   |  12 +-
 drivers/net/txgbe/base/txgbe_phy.c     |  25 +++-
 drivers/net/txgbe/base/txgbe_phy.h     |   7 +
 drivers/net/txgbe/base/txgbe_regs.h    |   3 +
 drivers/net/txgbe/base/txgbe_type.h    |  17 ++-
 drivers/net/txgbe/txgbe_ethdev.c       | 178 ++++++++++++++++++++--
 drivers/net/txgbe/txgbe_ethdev.h       |   2 +
 drivers/net/txgbe/txgbe_rxtx.c         |   1 -
 17 files changed, 502 insertions(+), 128 deletions(-)

-- 
2.55.0.windows.2