<div dir="ltr">No Honnappa. <div><br></div><div>Thanks & Regards,</div><div>Rajasekhar</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Mar 8, 2023 at 5:49 AM Honnappa Nagarahalli <<a href="mailto:Honnappa.Nagarahalli@arm.com">Honnappa.Nagarahalli@arm.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><br>
<br>
From: Rajasekhar Pulluru <<a href="mailto:pullururajasekhar@gmail.com" target="_blank">pullururajasekhar@gmail.com</a>> <br>
Sent: Tuesday, March 7, 2023 12:52 PM<br>
To: <a href="mailto:dev@dpdk.org" target="_blank">dev@dpdk.org</a><br>
Subject: ixgbe rxq interrupt not working<br>
<br>
Hi Team,<br>
<br>
Bringing-up dpdk-22.07 on an intel machine with 8 ports, 4 of them driven by igb and the rest of the 4 ports driven by ixgbe. <br>
[Honnappa]  Do you have packets crossing between the 2 drivers?<br>
<br>
<br>
I am following the below sequence to initialize these ports:<br>
<br>
dev_conf.intr_conf.lsc = 1; //Enable link state change interrupt<br>
dev_conf.intr_conf.rxq = 1; //Enable RX Queue Interrupt<br>
dev_conf.rxmode.mq_mode = RTE_ETH_MQ_RX_NONE;<br>
dev_conf.rxmode.offloads = 0;<br>
dev_conf.txmode.mq_mode = RTE_ETH_MQ_TX_NONE;<br>
dev_conf.txmode.offloads = 0;<br>
<br>
rte_eth_dev_configure<br>
rte_eth_rx_queue_setup<br>
rte_eth_tx_queue_setup<br>
rte_eth_dev_start<br>
data = port_id << CHAR_BIT | queue_id;<br>
rte_eth_dev_rx_intr_ctl_q(port_id, queue_id, RTE_EPOLL_PER_THREAD, RTE_INTR_EVENT_ADD, (void *)((uintptr_t)data));<br>
rte_eth_dev_rx_intr_enable(port_id, queue_id);<br>
<br>
And then main loop repeats the below:<br>
<br>
rte_epoll_wait(RTE_EPOLL_PER_THREAD, event, 1, timeout /* 200micro-sec */); /* ignore return value */<br>
rte_eth_dev_rx_intr_disable(port_id, queue_id);<br>
rte_eth_rx_burst(port_id, queue_id, pkts, num_pkts);<br>
rte_eth_dev_rx_intr_enable(port_id, queue_id);<br>
<br>
The code is same for all the ports, igb ports are able to come-up and rx packets, where-as the ixgbe ports are not able to rx packets at all.<br>
cat /proc/interrupts dumps vfio-msix counters for ixgbe as 0, where-as it's non-zero for igb. <br>
If I don't use/enable rxq interrupt for ixgbe (and remove epoll wait, interrupt enable/disable from while loop) and simply poll for rte_eth_rx_burst in a loop, ixgbe ports are able to rx packets.<br>
<br>
What could be wrong here? Appreciate any help.<br>
<br>
I would also like to know if there's an asynchronous rxq interrupt notification to the application instead of rte_epoll_wait (and sleep).<br>
<br>
Thanks & Regards,<br>
Rajasekhar<br>
</blockquote></div>