[spp] [PATCH] bin: add interfaces of spp_primary for start.sh

[yasufum.o at gmail.com]

From: Yasufumi Ogawa <yasufum.o at gmail.com>

Startup script `start.sh` supports using vdevs, but only for vhost. This
update is to add `ring` and `tap` types for the interface.

Signed-off-by: Yasufumi Ogawa <yasufum.o at gmail.com>
---
 bin/sample/config.sh |  2 ++
 bin/spp_pri.sh       | 30 ++++++++++++++++++++++++++----
 bin/start.sh         |  4 +++-
 3 files changed, 31 insertions(+), 5 deletions(-)

diff --git a/bin/sample/config.sh b/bin/sample/config.sh
index 915c093..9bdee41 100644
--- a/bin/sample/config.sh
+++ b/bin/sample/config.sh
@@ -12,6 +12,8 @@ PRI_MEMCHAN=4  # change for your memory channels.
 NUM_RINGS=8
 PRI_PORTMASK=0x03  # total num of ports of spp_primary.
 #PRI_VHOST_IDS=(11 12)  # you use if you have no phy ports.
+#PRI_RING_IDS=(1 2)  # you use if you have no phy ports.
+#PRI_TAP_IDS=(1 2)  # you use if you have no phy ports.
 
 # You do not need to change usually.
 # Log files created in 'spp/log/'.
diff --git a/bin/spp_pri.sh b/bin/spp_pri.sh
index 2f45b83..62a6075 100644
--- a/bin/spp_pri.sh
+++ b/bin/spp_pri.sh
@@ -5,22 +5,42 @@
 #set -x
 
 SPP_PRI_VHOST=""
+SPP_PRI_RING=""
+SPP_PRI_TAP=""
 
 function clean_sock_files() {
     # clean /tmp/sock*
     sudo rm -f /tmp/sock*
 }
 
-# Add vdevs if no physical ports.
-function setup_vdevs() {
-    if [ ${PRI_VHOST_IDS} ]; then
-        for id in ${PRI_VHOST_IDS[@]}; do
+# Add vhost vdevs.
+function setup_vhost_vdevs() {
+    if [ ${PRI_VHOST_VDEVS} ]; then
+        for id in ${PRI_VHOST_VDEVS[@]}; do
             SPP_SOCK="/tmp/sock${id}"
             SPP_PRI_VHOST="${SPP_PRI_VHOST} --vdev eth_vhost${id},iface=${SPP_SOCK}"
         done
     fi
 }
 
+# Add ring vdevs.
+function setup_ring_vdevs() {
+    if [ ${PRI_RING_VDEVS} ]; then
+        for id in ${PRI_RING_VDEVS[@]}; do
+            SPP_PRI_RING="${SPP_PRI_RING} --vdev net_ring${id}"
+        done
+    fi
+}
+
+# Add tap vdevs.
+function setup_tap_vdevs() {
+    if [ ${PRI_TAP_VDEVS} ]; then
+        for id in ${PRI_TAP_VDEVS[@]}; do
+            SPP_PRI_TAP="${SPP_PRI_TAP} --vdev net_tap${id},iface=vtap${id}"
+        done
+    fi
+}
+
 # Launch spp_primary.
 function spp_pri() {
     SPP_PRI_BIN=${SPP_DIR}/src/primary/${RTE_TARGET}/spp_primary
@@ -33,6 +53,8 @@ function spp_pri() {
         --base-virtaddr 0x100000000 \
         --log-level ${LOGLEVEL} \
         ${SPP_PRI_VHOST} \
+        ${SPP_PRI_RING} \
+        ${SPP_PRI_TAP} \
         -- \
         -p ${PRI_PORTMASK} \
         -n ${NUM_RINGS} \
diff --git a/bin/start.sh b/bin/start.sh
index 9bc1ff0..bf57d4e 100755
--- a/bin/start.sh
+++ b/bin/start.sh
@@ -31,7 +31,9 @@ python3 ${SPP_DIR}/src/spp-ctl/spp-ctl -b ${SPP_HOST_IP} \
 echo "Start spp_primary"
 . ${SPP_DIR}/bin/spp_pri.sh
 clean_sock_files  # remove /tmp/sock* as initialization
-setup_vdevs  # you use vdevs if you have no phy ports
+setup_vhost_vdevs  # you use vdevs if you have no phy ports
+setup_ring_vdevs  # you use vdevs if you have no phy ports
+setup_tap_vdevs  # you use vdevs if you have no phy ports
 spp_pri  # launch spp_primary
 
 echo "Waiting for spp-ctl is ready ..."
-- 
2.17.1