[dpdk-users] Failed to initialize one specific port of X710-DA4 in i40e pmd

[Aaron Hughes]

Hi Hitoshi,

Did you ever figure out a solution to your problem with the X710?  I'm
seeing the same problem with an XL710 using DPDK version 17.05 on Redhat
7.5:

validate_tcmap_parameter(): Enabled TC map 0x80 not applicable to HW
support 0x1
i40e_vsi_setup(): Failed to update TC bandwidth
i40e_pf_setup(): Setup of main vsi failed
eth_i40e_dev_init(): Failed to setup pf switch: -63

Thanks,
Aaron

I am facing a failure of dpdk(16.11.3) initialization with testpmd
> using i40e pmd on a specific physical port of X710-DA4.
>
> Without such specific port, testpmd can run successfully.
>
> My server box has two X710-DA4 cards and
> these two cards have the same failure.
>
> To clarify whether it is caused by hardware failure or
> by the lack of appropriate nic configuration,
> the following build options of dpdk are enabled.
>
> --------------
> CONFIG_RTE_LIBRTE_ETHDEV_DEBUG=y
> CONFIG_RTE_LIBRTE_I40E_DEBUG_INIT=y
> CONFIG_RTE_LIBRTE_I40E_DEBUG_DRIVER=y
> --------------
>
> My server box spec. is as follows :
>
> CPU        : Intel(R) Xeon(R) Gold 6136
> MEMORY     : 128GB (16G x 8)
> Motherboard: SYS-1029U-TR4
> NIC1       : I350 x 4 (onboard nic)
> NIC2       : XL710 dual
> NIC3       : X710-DA4
> NIC4       : X710-DA4
> ------------------------------------------------------------
> OS         : ubnutu 16.04.3 LTS(linux-image-4.4.0-87-generic)
> DPDK       : 16.11.3
>
> testpmd's boot message is as follows :
> --------------------------------------------
> $ sudo ./testpmd -- -i
>
> EAL: Detected 24 lcore(s)
> EAL: Probing VFIO support...
> EAL: PCI device 0000:18:00.0 on NUMA socket 0
> EAL:   probe driver: 8086:1521 net_e1000_igb
> EAL: PCI device 0000:18:00.1 on NUMA socket 0
> EAL:   probe driver: 8086:1521 net_e1000_igb
> EAL: PCI device 0000:18:00.2 on NUMA socket 0
> EAL:   probe driver: 8086:1521 net_e1000_igb
> EAL: PCI device 0000:18:00.3 on NUMA socket 0
> EAL:   probe driver: 8086:1521 net_e1000_igb
> EAL: PCI device 0000:86:00.0 on NUMA socket 1
> EAL:   probe driver: 8086:1583 net_i40e
> EAL: PCI device 0000:86:00.1 on NUMA socket 1
> EAL:   probe driver: 8086:1583 net_i40e
> EAL: PCI device 0000:af:00.0 on NUMA socket 1
> EAL:   probe driver: 8086:1572 net_i40e
> PMD: i40e_set_symmetric_hash_enable_per_port(): Symmetric hash has
> already been disabled
> PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.05 eetrack 80002919
> PMD: i40e_update_default_filter_setting(): Cannot remove the default
> macvlan filter
> PMD: i40e_pf_setup(): i40e_vsi_setup finished
> PMD: i40e_pf_setup(): Hardware capability of hash lookup table size: 512
>
> PMD: i40e_update_flow_control(): Link auto negotiation not completed
> EAL: PCI device 0000:af:00.1 on NUMA socket 1
> EAL:   probe driver: 8086:1572 net_i40e
> EAL: PCI device 0000:af:00.2 on NUMA socket 1
> EAL:   probe driver: 8086:1572 net_i40e
> PMD: i40e_set_symmetric_hash_enable_per_port(): Symmetric hash has
> already been disabled
> PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.05 eetrack 80002919
> PMD: validate_tcmap_parameter(): Enabled TC map 0x80 not applicable to
> HW support 0x1
> PMD: i40e_vsi_setup(): Failed to update TC bandwidth
> PMD: i40e_pf_setup(): Setup of main vsi failed
> PMD: eth_i40e_dev_init(): Failed to setup pf switch: -63
> rte_eth_dev_pci_probe: driver net_i40e: eth_dev_init(vendor_id=0x8086
> device_id=0x1572) failed
> EAL: Error - exiting with code: 1
>      Cause: Requested device 0000:af:00.2 cannot be used
> ---------------------------
>
> If you have solutions, could you tell me how this problem can be resolved ?
>
> Regards,
> Hitoshi
>
>