[dpdk-users] Unable to launch testpmd with Mellanox ConnectX-3 Pro NIC

Timur Bogdanov timurbogdanov at gmail.com
Sat Jan 20 20:10:58 CET 2018


Finally I managed to run testpmd normally after updating a kernel to
4.14.14 and installing rdma-core_v17 from sources.

Tnx for the advice of setting parameter log_num_mgm_entry_size" to "-1"
/Regards, Timur


On Fri, Jan 19, 2018 at 2:10 PM, Timur Bogdanov <timurbogdanov at gmail.com> wrote:
> Server kernel is 4.14.13-1.el7.elrepo.x86_64.
> The rdma-core is v16.
> Parameter "log_num_mgm_entry_size" is set to "-1"
> So I don't know why testpmd still runs with same error:
>
> PMD: net_mlx4: 0xda13c0: cannot attach flow rules (code 95, "Operation
> not supported"), flow error type 2, cause 0x7f2869cdab80, message:
> flow rule rejected by device
> /Regards, Timur
>
>
> On Thu, Jan 18, 2018 at 6:05 PM, Adrien Mazarguil
> <adrien.mazarguil at 6wind.com> wrote:
>> On Thu, Jan 18, 2018 at 03:11:16PM +0300, Timur Bogdanov wrote:
>>> Yes, the problem was in this parameter and after changing it to "-1"
>>> testpmd application has been started successfully.
>>>
>>> BUT, it started successfully only on server where Mellanox OFED is installed.
>>>
>>> On  another server a rdma-core was installed from sources. (rpm's were
>>> built and installed)
>>> I also changed the value of log_num_mgm_entry_size parameter to "-1"
>>> and restarted a server (since where is no openibd service on this
>>> server) and got the same error.
>>> Maybe mlx4_core kernel module parameter should be changed in some
>>> other config file?
>>
>> In case MLNX_OFED is *not* installed, do both rdma-core and kernel version
>> meet the minimum requirements?
>>
>> - rdma-core v15
>> - Linux 4.14
>>
>> Note while the above versions are fine for mlx5 (ConnectX-4, ConnectX-5),
>> they provide reduced performance and RSS capabilities for mlx4 (ConnectX-3),
>> for which I recommend to use at least:
>>
>> - rdma-core v16
>> - Linux 4.15 (not released yet, 4.15-rc8 will do in the meantime)
>>
>>> Anyway, I can also install and use OFED instead of RDMA but the RDMA
>>> is pointed as recommended on instructions page
>>> "http://dpdk.org/doc/guides/nics/mlx4.html" and it is interesting to
>>> bring it to working state.
>>> /Regards, Timur
>>
>> rdma-core requires an up-to-date kernel. If this can't be satisfied,
>> MLNX_OFED is the only alternative (the mlnx-ofa_kernel package).
>>
>>> On Thu, Jan 18, 2018 at 11:48 AM, Adrien Mazarguil
>>> <adrien.mazarguil at 6wind.com> wrote:
>>> > On Tue, Jan 16, 2018 at 06:59:31PM +0300, Timur Bogdanov wrote:
>>> >> Hi,
>>> >>
>>> >> I'm trying to use dpdk with Mellanox ConnectX-3 Pro NIC.
>>> >> I built PMD for it according to instructions on
>>> >> "http://dpdk.org/doc/guides/nics/mlx4.html" and tried to launch
>>> >> testpmd app but got following error:
>>> > <snip>
>>> >> PMD: net_mlx4: 0xda13c0: cannot attach flow rules (code 95, "Operation
>>> >> not supported"), flow error type 2, cause 0x7f2869cdab80, message:
>>> >> flow rule rejected by device
>>> >>
>>> >> Fail to start port 0
>>> > <snip>
>>> >> What can be the reason of testpmd does not start correctly?
>>> >
>>> > Did you provide by any chance -7 instead of -1 as a value for mlx4_core.ko's
>>> > log_num_mgm_entry_size parameter (as recommended by the above
>>> > documentation)?
>>> >
>>> > Timothy (CC'ed) reported that -7 does not quite work with the default flow
>>> > rules (too many limitations) and results in the above error message. -1
>>> > should be used, -7 is only for specific use cases and should probably not
>>> > even be documented in this file.
>>> >
>>> > --
>>> > Adrien Mazarguil
>>> > 6WIND
>>
>> --
>> Adrien Mazarguil
>> 6WIND


More information about the users mailing list