Command line on Intel board 1: -------------------------------- ./build/ipsec-secgw -l 1 -n 4 -w b3:00.0 -w b3:00.1 -w 67:01.0 -- -P -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep0-intel-board1.cfg Output: ---------------- EAL: Detected 36 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: 20 hugepages of size 1073741824 reserved, but no mounted hugetlbfs found for that size EAL: Probing VFIO support... EAL: VFIO support initialized EAL: PCI device 0000:67:01.0 on NUMA socket 0 EAL: probe driver: 8086:37c9 qat EAL: using IOMMU type 1 (Type 1) CRYPTODEV: Creating cryptodev 0000:67:01.0_qat_sym CRYPTODEV: Initialisation parameters - name: 0000:67:01.0_qat_sym,socket id: 0, max queue pairs: 0 EAL: PCI device 0000:b3:00.0 on NUMA socket 0 EAL: probe driver: 8086:1583 net_i40e EAL: PCI device 0000:b3:00.1 on NUMA socket 0 EAL: probe driver: 8086:1583 net_i40e Promiscuous mode selected Creating SA context with 128 maximum entries spi_in(1010):aes-128-cbc sha1-hmac mode:IP4Tunnel 20.1.1.20 20.1.1.50 Creating SA context with 128 maximum entries spi_out(1000):aes-128-cbc sha1-hmac mode:IP4Tunnel 20.1.1.50 20.1.1.20 Creating SP context with 1024 max rules IPv4 sp_ip4_in_0 entries [1]: 1:20.1.1.20/32 20.1.1.50/32 0 : 65535 0 : 65535 0x0/0x0 0x1-0x5-0x72 acl context @0x1007adb80 socket_id=0 alg=3 max_rules=1024 rule_size=96 num_rules=1 num_categories=1 num_tries=1 Creating SP context with 1024 max rules IPv4 sp_ip4_out_0 entries [1]: 1:0.0.0.0/0 40.1.1.0/24 0 : 65535 0 : 65535 0x0/0x0 0x1-0x5-0x68 acl context @0x100795780 socket_id=0 alg=3 max_rules=1024 rule_size=96 num_rules=1 num_categories=1 num_tries=1 IPSEC: No IPv6 SP Inbound rule specified IPSEC: No IPv6 SP Outbound rule specified Creating IPv4 Routing Table (RT) context with 1024 max routes LPM: Adding route 20.1.1.20/32 (1) LPM: Adding route 30.1.1.10/32 (0) Allocated mbuf pool on socket 0 Configuring device port 0: Address: 40:A6:B7:02:70:48 Creating queues: nb_rx_queue=1 nb_tx_queue=1... Port 0 modified RSS hash function based on hardware support,requested:0x3bffc configured:0x3ef8 Setup txq=1,0,0 Setup rxq=0,0,0 Configuring device port 1: Address: 40:A6:B7:02:70:49 Creating queues: nb_rx_queue=1 nb_tx_queue=1... Port 1 modified RSS hash function based on hardware support,requested:0x3bffc configured:0x3ef8 Setup txq=1,0,0 Setup rxq=1,0,0 cryptodevs_init: <--- cryptodevs_init: rte_cryptodev_count: 1 lcore/cryptodev/qp mappings: Inbound cdev mapping: lcore 1 using cdev 0 qp 0 (cdev_id_qp 0) Outbound cdev mapping: lcore 1 using cdev 0 qp 1 (cdev_id_qp 0) Allocated session pool on socket 0 Checking link status..........................................................................................done Port0 Link Up - speed 40000 Mbps -full-duplex Port 1 Link Down IPSEC: entering main loop on lcore 1 IPSEC: -- lcoreid=1 portid=0 rxqueueid=0 IPSEC: -- lcoreid=1 portid=1 rxqueueid=0