[dpdk-dev] [PATCH v4 3/7] pmd: igb/ixgbe split nb_q_per_pool to rx and tx nb_q_per_pool

[Ouyang, Changchun]

> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Pawel Wodkowski
> Sent: Thursday, February 19, 2015 11:55 PM
> To: dev at dpdk.org
> Subject: [dpdk-dev] [PATCH v4 3/7] pmd: igb/ixgbe split nb_q_per_pool to rx
> and tx nb_q_per_pool
> 
> rx and tx number of queue might be different if RX and TX are configured in
> different mode. This allow to inform VF about proper number of queues.
> 
> Signed-off-by: Pawel Wodkowski <pawelx.wodkowski at intel.com>
> ---
>  lib/librte_ether/rte_ethdev.c       | 12 ++++++------
>  lib/librte_ether/rte_ethdev.h       |  3 ++-
>  lib/librte_pmd_e1000/igb_pf.c       |  3 ++-
>  lib/librte_pmd_ixgbe/ixgbe_ethdev.c |  2 +-
>  lib/librte_pmd_ixgbe/ixgbe_pf.c     |  9 +++++----
>  5 files changed, 16 insertions(+), 13 deletions(-)
> 
> diff --git a/lib/librte_ether/rte_ethdev.c b/lib/librte_ether/rte_ethdev.c
> index 2e814db..4007054 100644
> --- a/lib/librte_ether/rte_ethdev.c
> +++ b/lib/librte_ether/rte_ethdev.c
> @@ -520,7 +520,7 @@ rte_eth_dev_check_vf_rss_rxq_num(uint8_t port_id,
> uint16_t nb_rx_q)
>  		return -EINVAL;
>  	}
> 
> -	RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool = nb_rx_q;
> +	RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool = nb_rx_q;
>  	RTE_ETH_DEV_SRIOV(dev).def_pool_q_idx =
>  		dev->pci_dev->max_vfs * nb_rx_q;
> 
> @@ -567,7 +567,7 @@ rte_eth_dev_check_mq_mode(uint8_t port_id,
> uint16_t nb_rx_q, uint16_t nb_tx_q,
>  					dev->data-
> >dev_conf.rxmode.mq_mode);
>  		case ETH_MQ_RX_VMDQ_RSS:
>  			dev->data->dev_conf.rxmode.mq_mode =
> ETH_MQ_RX_VMDQ_RSS;
> -			if (nb_rx_q <=
> RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool)
> +			if (nb_rx_q <=
> RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool)
>  				if
> (rte_eth_dev_check_vf_rss_rxq_num(port_id, nb_rx_q) != 0) {
>  					PMD_DEBUG_TRACE("ethdev
> port_id=%d"
>  						" SRIOV active, invalid queue"
> @@ -580,8 +580,8 @@ rte_eth_dev_check_mq_mode(uint8_t port_id,
> uint16_t nb_rx_q, uint16_t nb_tx_q,
>  		default: /* ETH_MQ_RX_VMDQ_ONLY or
> ETH_MQ_RX_NONE */
>  			/* if nothing mq mode configure, use default scheme
> */
>  			dev->data->dev_conf.rxmode.mq_mode =
> ETH_MQ_RX_VMDQ_ONLY;
> -			if (RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool > 1)
> -				RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool =
> 1;
> +			if (RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool > 1)
> +
> 	RTE_ETH_DEV_SRIOV(dev).nb_rx_q_per_pool = 1;
>  			break;
>  		}
> 
> @@ -600,8 +600,8 @@ rte_eth_dev_check_mq_mode(uint8_t port_id,
> uint16_t nb_rx_q, uint16_t nb_tx_q,
>  		}
> 
>  		/* check valid queue number */
> -		if ((nb_rx_q > RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool) ||
> -		    (nb_tx_q > RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool)) {
> +		if ((nb_rx_q > RTE_ETH_DEV_SRIOV(dev).nb_tx_q_per_pool)

Here,  how about use nb_rx_q_per_pool to replace nb_tx_q_per_pool ?
so it will be more clear to check rx queue number.

> ||
> +		    (nb_tx_q > RTE_ETH_DEV_SRIOV(dev).nb_tx_q_per_pool))
> {
>  			PMD_DEBUG_TRACE("ethdev port_id=%d SRIOV
> active, "
>  				    "queue number must less equal to %d\n",
>  					port_id,
> RTE_ETH_DEV_SRIOV(dev).nb_q_per_pool);