[dpdk-dev] [PATCH v1 02/15] eal: new eal option '--lcores' for cpu assignment

Ananyev, Konstantin konstantin.ananyev at intel.com
Thu Jan 22 15:34:07 CET 2015


Hi Bruce,

> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Bruce Richardson
> Sent: Thursday, January 22, 2015 12:19 PM
> To: Liang, Cunming
> Cc: dev at dpdk.org
> Subject: Re: [dpdk-dev] [PATCH v1 02/15] eal: new eal option '--lcores' for cpu assignment
> 
> On Thu, Jan 22, 2015 at 04:16:25PM +0800, Cunming Liang wrote:
> > It supports one new eal long option '--lcores' for EAL thread cpuset assignment.
> >
> > The format pattern:
> > 	--lcores='lcores[@cpus]<,lcores[@cpus]>'
> > lcores, cpus could be a single digit or a group.
> > '(' and ')' are necessary if it's a group.
> > If not supply '@cpus', the value of cpus uses the same as lcores.
> >
> > e.g. '1,2@(5-7),(3-5)@(0,2),(0,6)' means starting 7 EAL thread as below
> >   lcore 0 runs on cpuset 0x41 (cpu 0,6)
> >   lcore 1 runs on cpuset 0x2 (cpu 1)
> >   lcore 2 runs on cpuset 0xe0 (cpu 5,6,7)
> >   lcore 3,4,5 runs on cpuset 0x5 (cpu 0,2)
> >   lcore 6 runs on cpuset 0x41 (cpu 0,6)
> >
> 
> This strikes me as very confusing, though a couple of tweaks might help with
> readability. The lcore 0 at the end is especially confusing.

Didn't get you here: do you find (0,6) confusing, right?
Because braces implicitly specifies affinity for group of en-braced lcores? 

> Perhaps we can
> limit the allowed formats here,
> * require the lcore_id to be specified - the lack of an lcore id for the last part
> makes having it as lcore 0 surprising.

Again, not sure I understand you properly:  lcore_id(s) are always specified explicitly. 
Physical cpus part might be omitted.

> * only allow one lcore id to be given for each set of cores.

So you mean for '(3-5)@(0,2)' user would have to: '3@(0,2),4@(0,2),5@(0,2)'?
I don't see big difference here, but imagine you'd like to create a pool of 32 EAL-threads running on same cpu set.
With current syntax it is just something like: '(32-63)@(0-7)'.
With what you proposing it will be a very long list.  

> 
> I think it may still be readable if we allow the core set to be omitted if its
> to be the same as the lcore_id.

I think that is supported.
See lcore_id=1 in Steve's example above.
As I understand: --lcores='0,2,3-5' is equal to '-l 0,2,3-5' and to '-c 0x3d'.

Konstantin

> 
> It's probably still not going to be very tidy, but I think we can improve things.
> 
> /Bruce
> 
> > Signed-off-by: Cunming Liang <cunming.liang at intel.com>
> > ---
> >  lib/librte_eal/common/eal_common_launch.c  |   1 -
> >  lib/librte_eal/common/eal_common_options.c | 262 ++++++++++++++++++++++++++++-
> >  lib/librte_eal/common/eal_options.h        |   2 +
> >  lib/librte_eal/linuxapp/eal/Makefile       |   1 +
> >  4 files changed, 261 insertions(+), 5 deletions(-)
> >
> > diff --git a/lib/librte_eal/common/eal_common_launch.c b/lib/librte_eal/common/eal_common_launch.c
> > index 599f83b..2d732b1 100644
> > --- a/lib/librte_eal/common/eal_common_launch.c
> > +++ b/lib/librte_eal/common/eal_common_launch.c
> > @@ -117,4 +117,3 @@ rte_eal_mp_wait_lcore(void)
> >  		rte_eal_wait_lcore(lcore_id);
> >  	}
> >  }
> > -
> > diff --git a/lib/librte_eal/common/eal_common_options.c b/lib/librte_eal/common/eal_common_options.c
> > index e2810ab..fc47588 100644
> > --- a/lib/librte_eal/common/eal_common_options.c
> > +++ b/lib/librte_eal/common/eal_common_options.c
> > @@ -45,6 +45,7 @@
> >  #include <rte_lcore.h>
> >  #include <rte_version.h>
> >  #include <rte_devargs.h>
> > +#include <rte_memcpy.h>
> >
> >  #include "eal_internal_cfg.h"
> >  #include "eal_options.h"
> > @@ -85,6 +86,7 @@ eal_long_options[] = {
> >  	{OPT_XEN_DOM0, 0, 0, OPT_XEN_DOM0_NUM},
> >  	{OPT_CREATE_UIO_DEV, 1, NULL, OPT_CREATE_UIO_DEV_NUM},
> >  	{OPT_VFIO_INTR, 1, NULL, OPT_VFIO_INTR_NUM},
> > +	{OPT_LCORES, 1, 0, OPT_LCORES_NUM},
> >  	{0, 0, 0, 0}
> >  };
> >
> > @@ -255,9 +257,11 @@ eal_parse_corelist(const char *corelist)
> >  			if (min == RTE_MAX_LCORE)
> >  				min = idx;
> >  			for (idx = min; idx <= max; idx++) {
> > -				cfg->lcore_role[idx] = ROLE_RTE;
> > -				lcore_config[idx].core_index = count;
> > -				count++;
> > +				if (cfg->lcore_role[idx] != ROLE_RTE) {
> > +					cfg->lcore_role[idx] = ROLE_RTE;
> > +					lcore_config[idx].core_index = count;
> > +					count++;
> > +				}
> >  			}
> >  			min = RTE_MAX_LCORE;
> >  		} else
> > @@ -289,6 +293,241 @@ eal_parse_master_lcore(const char *arg)
> >  	return 0;
> >  }
> >
> > +/*
> > + * Parse elem, the elem could be single number or '(' ')' group
> > + * Within group elem, '-' used for a range seperator;
> > + *                    ',' used for a single number.
> > + */
> > +static int
> > +eal_parse_set(const char *input, uint16_t set[], unsigned num)
> > +{
> > +	unsigned idx;
> > +	const char *str = input;
> > +	char *end = NULL;
> > +	unsigned min, max;
> > +
> > +	memset(set, 0, num * sizeof(uint16_t));
> > +
> > +	while (isblank(*str))
> > +		str++;
> > +
> > +	/* only digit or left bracket is qulify for start point */
> > +	if ((!isdigit(*str) && *str != '(') || *str == '\0')
> > +		return -1;
> > +
> > +	/* process single number */
> > +	if (*str != '(') {
> > +		errno = 0;
> > +		idx = strtoul(str, &end, 10);
> > +		if (errno || end == NULL || idx >= num)
> > +			return -1;
> > +		else {
> > +			while (isblank(*end))
> > +				end++;
> > +
> > +			if (*end != ',' && *end != '\0' &&
> > +			    *end != '@')
> > +				return -1;
> > +
> > +			set[idx] = 1;
> > +			return end - input;
> > +		}
> > +	}
> > +
> > +	/* process set within bracket */
> > +	str++;
> > +	while (isblank(*str))
> > +		str++;
> > +	if (*str == '\0')
> > +		return -1;
> > +
> > +	min = RTE_MAX_LCORE;
> > +	do {
> > +
> > +		/* go ahead to the first digit */
> > +		while (isblank(*str))
> > +			str++;
> > +		if (!isdigit(*str))
> > +			return -1;
> > +
> > +		/* get the digit value */
> > +		errno = 0;
> > +		idx = strtoul(str, &end, 10);
> > +		if (errno || end == NULL || idx >= num)
> > +			return -1;
> > +
> > +		/* go ahead to separator '-',',' and ')' */
> > +		while (isblank(*end))
> > +			end++;
> > +		if (*end == '-') {
> > +			if (min == RTE_MAX_LCORE)
> > +				min = idx;
> > +			else /* avoid continuous '-' */
> > +				return -1;
> > +		} else if ((*end == ',') || (*end == ')')) {
> > +			max = idx;
> > +			if (min == RTE_MAX_LCORE)
> > +				min = idx;
> > +			for (idx = RTE_MIN(min, max);
> > +			     idx <= RTE_MAX(min, max); idx++)
> > +				set[idx] = 1;
> > +
> > +			min = RTE_MAX_LCORE;
> > +		} else
> > +			return -1;
> > +
> > +		str = end + 1;
> > +	} while (*end != '\0' && *end != ')');
> > +
> > +	return str - input;
> > +}
> > +
> > +/* convert from set array to cpuset bitmap */
> > +static inline int
> > +convert_to_cpuset(rte_cpuset_t *cpusetp,
> > +	      uint16_t *set, unsigned num)
> > +{
> > +	unsigned idx;
> > +
> > +	CPU_ZERO(cpusetp);
> > +
> > +	for (idx = 0; idx < num; idx++) {
> > +		if (!set[idx])
> > +			continue;
> > +
> > +		if (!lcore_config[idx].detected) {
> > +			RTE_LOG(ERR, EAL, "core %u "
> > +				"unavailable\n", idx);
> > +			return -1;
> > +		}
> > +
> > +		CPU_SET(idx, cpusetp);
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +/*
> > + * The format pattern: --lcores='lcores[@cpus]<,lcores[@cpus]>'
> > + * lcores, cpus could be a single digit or a group.
> > + * '(' and ')' are necessary if it's a group.
> > + * If not supply '@cpus', the value of cpus uses the same as lcores.
> > + * e.g. '1,2@(5-7),(3-5)@(0,2),(0,6)' means start 7 EAL thread as below
> > + *   lcore 0 runs on cpuset 0x41 (cpu 0,6)
> > + *   lcore 1 runs on cpuset 0x2 (cpu 1)
> > + *   lcore 2 runs on cpuset 0xe0 (cpu 5,6,7)
> > + *   lcore 3,4,5 runs on cpuset 0x5 (cpu 0,2)
> > + *   lcore 6 runs on cpuset 0x41 (cpu 0,6)
> > + */
> > +static int
> > +eal_parse_lcores(const char *lcores)
> > +{
> > +	struct rte_config *cfg = rte_eal_get_configuration();
> > +	static uint16_t set[RTE_MAX_LCORE];
> > +	unsigned idx = 0;
> > +	int i;
> > +	unsigned count = 0;
> > +	const char *lcore_start = NULL;
> > +	const char *end = NULL;
> > +	int offset;
> > +	rte_cpuset_t cpuset;
> > +	int ret = -1;
> > +
> > +	if (lcores == NULL)
> > +		return -1;
> > +
> > +	/* Remove all blank characters ahead and after */
> > +	while (isblank(*lcores))
> > +		lcores++;
> > +	i = strnlen(lcores, sysconf(_SC_ARG_MAX));
> > +	while ((i > 0) && isblank(lcores[i - 1]))
> > +		i--;
> > +
> > +	CPU_ZERO(&cpuset);
> > +
> > +	/* Reset lcore config */
> > +	for (idx = 0; idx < RTE_MAX_LCORE; idx++) {
> > +		cfg->lcore_role[idx] = ROLE_OFF;
> > +		lcore_config[idx].core_index = -1;
> > +		CPU_ZERO(&lcore_config[idx].cpuset);
> > +	}
> > +
> > +	/* Get list of cores */
> > +	do {
> > +		while (isblank(*lcores))
> > +			lcores++;
> > +		if (*lcores == '\0')
> > +			goto err;
> > +
> > +		/* record lcore_set start point */
> > +		lcore_start = lcores;
> > +
> > +		/* go across a complete bracket */
> > +		if (*lcore_start == '(') {
> > +			lcores += strcspn(lcores, ")");
> > +			if (*lcores++ == '\0')
> > +				goto err;
> > +		}
> > +
> > +		/* scan the separator '@', ','(next) or '\0'(finish) */
> > +		lcores += strcspn(lcores, "@,");
> > +
> > +		if (*lcores == '@') {
> > +			/* explict assign cpu_set */
> > +			offset = eal_parse_set(lcores + 1, set, RTE_DIM(set));
> > +			if (offset < 0)
> > +				goto err;
> > +
> > +			/* prepare cpu_set and update the end cursor */
> > +			if (0 > convert_to_cpuset(&cpuset,
> > +						  set, RTE_DIM(set)))
> > +				goto err;
> > +			end = lcores + 1 + offset;
> > +		} else  /* ',' or '\0' */
> > +			/* haven't given cpu_set, current loop done */
> > +			end = lcores;
> > +
> > +		if (*end != ',' && *end != '\0')
> > +			goto err;
> > +
> > +		/* parse lcore_set from start point */
> > +		if (0 > eal_parse_set(lcore_start, set, RTE_DIM(set)))
> > +			goto err;
> > +
> > +		/* without '@', by default using lcore_set as cpu_set */
> > +		if (*lcores != '@' &&
> > +		    0 > convert_to_cpuset(&cpuset, set, RTE_DIM(set)))
> > +			goto err;
> > +
> > +		/* start to update lcore_set */
> > +		for (idx = 0; idx < RTE_MAX_LCORE; idx++) {
> > +			if (!set[idx])
> > +				continue;
> > +
> > +			if (cfg->lcore_role[idx] != ROLE_RTE) {
> > +				lcore_config[idx].core_index = count;
> > +				cfg->lcore_role[idx] = ROLE_RTE;
> > +				count++;
> > +			}
> > +			rte_memcpy(&lcore_config[idx].cpuset, &cpuset,
> > +				   sizeof(rte_cpuset_t));
> > +		}
> > +
> > +		lcores = end + 1;
> > +	} while (*end != '\0');
> > +
> > +	if (count == 0)
> > +		goto err;
> > +
> > +	cfg->lcore_count = count;
> > +	lcores_parsed = 1;
> > +	ret = 0;
> > +
> > +err:
> > +
> > +	return ret;
> > +}
> > +
> >  static int
> >  eal_parse_syslog(const char *facility, struct internal_config *conf)
> >  {
> > @@ -489,6 +728,13 @@ eal_parse_common_option(int opt, const char *optarg,
> >  		conf->log_level = log;
> >  		break;
> >  	}
> > +	case OPT_LCORES_NUM:
> > +		if (eal_parse_lcores(optarg) < 0) {
> > +			RTE_LOG(ERR, EAL, "invalid parameter for --"
> > +				OPT_LCORES "\n");
> > +			return -1;
> > +		}
> > +		break;
> >
> >  	/* don't know what to do, leave this to caller */
> >  	default:
> > @@ -527,7 +773,7 @@ eal_check_common_options(struct internal_config *internal_cfg)
> >
> >  	if (!lcores_parsed) {
> >  		RTE_LOG(ERR, EAL, "CPU cores must be enabled with options "
> > -			"-c or -l\n");
> > +			"-c, -l or --lcores\n");
> >  		return -1;
> >  	}
> >  	if (cfg->lcore_role[cfg->master_lcore] != ROLE_RTE) {
> > @@ -583,6 +829,14 @@ eal_common_usage(void)
> >  	       "                 The argument format is <c1>[-c2][,c3[-c4],...]\n"
> >  	       "                 where c1, c2, etc are core indexes between 0 and %d\n"
> >  	       "  --"OPT_MASTER_LCORE" ID: Core ID that is used as master\n"
> > +	       "  --"OPT_LCORES" MAP: maps between lcore_set to phys_cpu_set\n"
> > +	       "                 The argument format is\n"
> > +	       "                       'lcores[@cpus]<,lcores[@cpus],...>'\n"
> > +	       "                 lcores and cpus list are grouped by '(' and ')'\n"
> > +	       "                 Within the group, '-' is used for range separator,\n"
> > +	       "                 ',' is used for single number separator.\n"
> > +	       "                 '( )' can be omitted for single element group, '@' \n"
> > +	       "                 can be omitted if cpus and lcores has the same value\n"
> >  	       "  -n NUM       : Number of memory channels\n"
> >  	       "  -v           : Display version information on startup\n"
> >  	       "  -m MB        : memory to allocate (see also --"OPT_SOCKET_MEM")\n"
> > diff --git a/lib/librte_eal/common/eal_options.h b/lib/librte_eal/common/eal_options.h
> > index e476f8d..a1cc59f 100644
> > --- a/lib/librte_eal/common/eal_options.h
> > +++ b/lib/librte_eal/common/eal_options.h
> > @@ -77,6 +77,8 @@ enum {
> >  	OPT_CREATE_UIO_DEV_NUM,
> >  #define OPT_VFIO_INTR    "vfio-intr"
> >  	OPT_VFIO_INTR_NUM,
> > +#define OPT_LCORES "lcores"
> > +	OPT_LCORES_NUM,
> >  	OPT_LONG_MAX_NUM
> >  };
> >
> > diff --git a/lib/librte_eal/linuxapp/eal/Makefile b/lib/librte_eal/linuxapp/eal/Makefile
> > index 0e9c447..025d836 100644
> > --- a/lib/librte_eal/linuxapp/eal/Makefile
> > +++ b/lib/librte_eal/linuxapp/eal/Makefile
> > @@ -95,6 +95,7 @@ CFLAGS_eal_hugepage_info.o := -D_GNU_SOURCE
> >  CFLAGS_eal_pci.o := -D_GNU_SOURCE
> >  CFLAGS_eal_pci_vfio.o := -D_GNU_SOURCE
> >  CFLAGS_eal_common_whitelist.o := -D_GNU_SOURCE
> > +CFLAGS_eal_common_options.o := -D_GNU_SOURCE
> >
> >  # workaround for a gcc bug with noreturn attribute
> >  # http://gcc.gnu.org/bugzilla/show_bug.cgi?id=12603
> > --
> > 1.8.1.4
> >


More information about the dev mailing list