[dpdk-dev] [PATCH 1/7] net/qede: reduce noise in debug logs

[Harish Patil]

Hi Ferruh,

>On 12/3/2016 2:43 AM, Harish Patil wrote:
>> From: Rasesh Mody <Rasesh.Mody at cavium.com>
>> 
>> Replace CONFIG_RTE_LIBRTE_QEDE_DEBUG_DRIVER with
>> CONFIG_RTE_LIBRTE_QEDE_DEBUG_VAL which is a 32-bit bitmapped value
>> where each bit represent a particular submodule to debug. Also move
>> notice messages under CONFIG_RTE_LIBRTE_QEDE_DEBUG_INFO.
>> 
>> Signed-off-by: Harish Patil <harish.patil at qlogic.com>
>> Signed-off-by: Rasesh Mody <Rasesh.Mody at cavium.com>
>> ---
>>  config/common_base             |  2 +-
>>  doc/guides/nics/qede.rst       |  4 ++--
>>  drivers/net/qede/qede_ethdev.c |  4 ++--
>>  drivers/net/qede/qede_logs.h   | 21 +++++----------------
>>  4 files changed, 10 insertions(+), 21 deletions(-)
>> 
>> diff --git a/config/common_base b/config/common_base
>> index 4bff83a..2ffd557 100644
>> --- a/config/common_base
>> +++ b/config/common_base
>> @@ -320,7 +320,7 @@ CONFIG_RTE_LIBRTE_BOND_DEBUG_ALB_L1=n
>>  CONFIG_RTE_LIBRTE_QEDE_PMD=y
>>  CONFIG_RTE_LIBRTE_QEDE_DEBUG_INIT=n
>>  CONFIG_RTE_LIBRTE_QEDE_DEBUG_INFO=n
>> -CONFIG_RTE_LIBRTE_QEDE_DEBUG_DRIVER=n
>> +CONFIG_RTE_LIBRTE_QEDE_DEBUG_VAL=0
>>  CONFIG_RTE_LIBRTE_QEDE_DEBUG_TX=n
>>  CONFIG_RTE_LIBRTE_QEDE_DEBUG_RX=n
>>  #Provides abs path/name of the firmware file.
>> diff --git a/doc/guides/nics/qede.rst b/doc/guides/nics/qede.rst
>> index d22ecdd..ddf4248 100644
>> --- a/doc/guides/nics/qede.rst
>> +++ b/doc/guides/nics/qede.rst
>> @@ -103,9 +103,9 @@ enabling debugging options may affect system
>>performance.
>>  
>>    Toggle display of generic debugging messages.
>>  
>> -- ``CONFIG_RTE_LIBRTE_QEDE_DEBUG_DRIVER`` (default **n**)
>> +- ``CONFIG_RTE_LIBRTE_QEDE_DEBUG_VAL`` (default **0**)
>
>Does it make sense to document how DEBUG_VAL used?
>
>Also commit log says bitmapped value to enable/disable a particular
>submodule, you may want to document here which value enable/disable
>which submodule.
>
>>  
>> -  Toggle display of ecore related messages.
>> +  Control driver debug verbosity using 32-bit bitmap flags.
>>  
>>  - ``CONFIG_RTE_LIBRTE_QEDE_DEBUG_TX`` (default **n**)
>>  

Not really, I think that would be too much. But if you think it really
helps then perhaps yes we can document.
Otherwise it is just for internal debugging.


>
><...>
>
>> diff --git a/drivers/net/qede/qede_logs.h b/drivers/net/qede/qede_logs.h
>> index 45c4af0..08fdf04 100644
>> --- a/drivers/net/qede/qede_logs.h
>> +++ b/drivers/net/qede/qede_logs.h
>> @@ -16,15 +16,18 @@
>>  		(p_dev)->name ? (p_dev)->name : "", \
>>  		##__VA_ARGS__)
>>  
>> +#ifdef RTE_LIBRTE_QEDE_DEBUG_INFO
>
>Is "_INFO" carries any meaning in this config option, why not just
>RTE_LIBRTE_QEDE_DEBUG?

INFO is used to mean just informational type of messages.
If you think it doesn’t make sense then I can rename it.

>
>>  #define DP_NOTICE(p_dev, is_assert, fmt, ...) \
>>  	rte_log(RTE_LOG_NOTICE, RTE_LOGTYPE_PMD,\
>>  		"[QEDE PMD: (%s)]%s:" fmt, \
>>  		(p_dev)->name ? (p_dev)->name : "", \
>>  		 __func__, \
>>  		##__VA_ARGS__)
>> +#else
>> +#define DP_NOTICE(p_dev, fmt, ...) do { } while (0)
>> +#endif
>>  
>>  #ifdef RTE_LIBRTE_QEDE_DEBUG_INFO
>> -
>>  #define DP_INFO(p_dev, fmt, ...) \
>>  	rte_log(RTE_LOG_INFO, RTE_LOGTYPE_PMD, \
>>  		"[%s:%d(%s)]" fmt, \
>> @@ -33,10 +36,8 @@
>>  		##__VA_ARGS__)
>>  #else
>>  #define DP_INFO(p_dev, fmt, ...) do { } while (0)
>> -
>>  #endif
>>  
>> -#ifdef RTE_LIBRTE_QEDE_DEBUG_DRIVER
>
>Are you sure you want to enable DP_VERBOSE, I guess most verbose log
>macro, by default? Perhaps may want to control it via
>RTE_LIBRTE_QEDE_DEBUG_INFO?

DP_VERBOSE is enabled but it has a check:
 if ((p_dev)->dp_module & module)
which controls what to print.
Here dp_module is controlled by CONFIG_RTE_LIBRTE_QEDE_DEBUG_VAL flag.
Hope it is clear.
>
>>  #define DP_VERBOSE(p_dev, module, fmt, ...) \
>>  do { \
>>  	if ((p_dev)->dp_module & module) \
>> @@ -46,9 +47,7 @@
>>  		      (p_dev)->name ? (p_dev)->name : "", \
>>  		      ##__VA_ARGS__); \
>>  } while (0)
>> -#else
>> -#define DP_VERBOSE(p_dev, fmt, ...) do { } while (0)
>> -#endif
>> +
>>  
><...>
>
>