[dpdk-dev] [PATCH] vhost: fix segfault on bad descriptor address.

Ilya Maximets i.maximets at samsung.com
Mon May 23 13:04:34 CEST 2016


On 23.05.2016 13:57, Yuanhan Liu wrote:
> On Fri, May 20, 2016 at 03:50:04PM +0300, Ilya Maximets wrote:
>> In current implementation guest application can reinitialize vrings
>> by executing start after stop. In the same time host application
>> can still poll virtqueue while device stopped in guest and it will
>> crash with segmentation fault while vring reinitialization because
>> of dereferencing of bad descriptor addresses.
>>
>> OVS crash for example:
>> <------------------------------------------------------------------------>
>> [test-pmd inside guest VM]
>>
>> 	testpmd> port stop all
>> 	    Stopping ports...
>> 	    Checking link statuses...
>> 	    Port 0 Link Up - speed 10000 Mbps - full-duplex
>> 	    Done
>> 	testpmd> port config all rxq 2
>> 	testpmd> port config all txq 2
>> 	testpmd> port start all
>> 	    Configuring Port 0 (socket 0)
>> 	    Port 0: 52:54:00:CB:44:C8
>> 	    Checking link statuses...
>> 	    Port 0 Link Up - speed 10000 Mbps - full-duplex
>> 	    Done
> 
> I actually didn't manage to reproduce it on my side, with the
> vhost-example instead of OVS though. Is that all the commands
> to reproduce it, and run them just after start test-pmd?

Actually, I think, packet flow should be enabled while performing
above actions and some traffic already should be sent through port
to change last used idx on vhost side.

Something like:
	start
	..wait a while.. see that packets are flowing.
	stop
	port stop
	port config
	port config
	port start
> 
>> [OVS on host]
>> 	Program received signal SIGSEGV, Segmentation fault.
>> 	rte_memcpy (n=2056, src=0xc, dst=0x7ff4d5247000) at rte_memcpy.h
>>
>> 	(gdb) bt
>> 	    #0  rte_memcpy (n=2056, src=0xc, dst=0x7ff4d5247000)
>> 	    #1  copy_desc_to_mbuf
>> 	    #2  rte_vhost_dequeue_burst
>> 	    #3  netdev_dpdk_vhost_rxq_recv
>> 	    ...
>>
>> 	(gdb) bt full
>> 	    #0  rte_memcpy
>> 	        ...
>> 	    #1  copy_desc_to_mbuf
>> 	        desc_addr = 0
>> 	        mbuf_offset = 0
>> 	        desc_offset = 12
>> 	        ...
>> <------------------------------------------------------------------------>
>>
>> Fix that by checking addresses of descriptors before using them.
>>
>> Note: For mergeable buffers this patch checks only guest's address for
>> zero, but in non-meargeable case host's address checked. This is done
>> because checking of host's address in mergeable case requires additional
>> refactoring to keep virtqueue in consistent state in case of error.
>>
>> Signed-off-by: Ilya Maximets <i.maximets at samsung.com>
>> ---
>>
>> Actually, current virtio implementation looks broken for me. Because
>> 'virtio_dev_start' breaks virtqueue while it still available from the vhost
>> side.
>>
>> There was 2 patches about this behaviour:
>>
>> 	1. a85786dc816f ("virtio: fix states handling during initialization")
>> 	2. 9a0615af7746 ("virtio: fix restart")
>>
>> The second patch fixes somehow issue intoduced in the first patch, but actually
>> also breaks vhost in the way described above.
>> It's not pretty clear for me what to do in current situation with virtio,
>> because it will be broken for guest application even if vhost will not crash.
>>
>> May be it'll be better to forbid stopping of virtio device and force user to
>> exit and start again (may be implemented in hidden from user way)?
>>
>> This patch adds additional sane checks, so it should be applied anyway, IMHO.
> 
> Agreed.
> 
> 	--yliu
> 
> 


More information about the dev mailing list