[dpdk-dev] [PATCH 3/4] net/enic: update VIC interface file
John Daley
johndale at cisco.com
Thu Sep 29 22:56:38 CEST 2016
Update the VIC adapter file which is common with the firmware and
other VIC drivers. This is needed to support new capabilities
for 1300 adapters, including advanced filtering, which is available
in VIC firmware version 2.0(13) for UCS rack and 3.1(2).
Signed-off-by: John Daley <johndale at cisco.com>
---
drivers/net/enic/base/vnic_devcmd.h | 346 ++++++++++++++++++++++++++++++++----
1 file changed, 308 insertions(+), 38 deletions(-)
diff --git a/drivers/net/enic/base/vnic_devcmd.h b/drivers/net/enic/base/vnic_devcmd.h
index b3d5a6c..785fd6f 100644
--- a/drivers/net/enic/base/vnic_devcmd.h
+++ b/drivers/net/enic/base/vnic_devcmd.h
@@ -1,5 +1,5 @@
/*
- * Copyright 2008-2010 Cisco Systems, Inc. All rights reserved.
+ * Copyright 2008-2016 Cisco Systems, Inc. All rights reserved.
* Copyright 2007 Nuova Systems, Inc. All rights reserved.
*
* Copyright (c) 2014, Cisco Systems, Inc.
@@ -126,7 +126,8 @@ enum vnic_devcmd_cmd {
/* dev-specific block member:
* in: (u16)a0=offset,(u8)a1=size
- * out: a0=value */
+ * out: a0=value
+ */
CMD_DEV_SPEC = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ALL, 2),
/* stats clear */
@@ -146,8 +147,9 @@ enum vnic_devcmd_cmd {
CMD_HANG_NOTIFY = _CMDC(_CMD_DIR_NONE, _CMD_VTYPE_ALL, 8),
/* MAC address in (u48)a0 */
- CMD_GET_MAC_ADDR = _CMDC(_CMD_DIR_READ,
+ CMD_MAC_ADDR = _CMDC(_CMD_DIR_READ,
_CMD_VTYPE_ENET | _CMD_VTYPE_FC, 9),
+#define CMD_GET_MAC_ADDR CMD_MAC_ADDR /* some uses are aliased */
/* add addr from (u48)a0 */
CMD_ADDR_ADD = _CMDCNW(_CMD_DIR_WRITE,
@@ -387,9 +389,8 @@ enum vnic_devcmd_cmd {
* Subvnic migration from MQ <--> VF.
* Enable the LIF migration from MQ to VF and vice versa. MQ and VF
* indexes are statically bound at the time of initialization.
- * Based on the
- * direction of migration, the resources of either MQ or the VF shall
- * be attached to the LIF.
+ * Based on the direction of migration, the resources of either MQ or
+ * the VF shall be attached to the LIF.
* in: (u32)a0=Direction of Migration
* 0=> Migrate to VF
* 1=> Migrate to MQ
@@ -397,7 +398,6 @@ enum vnic_devcmd_cmd {
*/
CMD_MIGRATE_SUBVNIC = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 53),
-
/*
* Register / Deregister the notification block for MQ subvnics
* in:
@@ -433,6 +433,10 @@ enum vnic_devcmd_cmd {
* in: (u64) a0= filter address
* (u32) a1= size of filter
* out: (u32) a0=filter identifier
+ *
+ * Capability query:
+ * out: (u64) a0= 1 if capability query supported
+ * (u64) a1= MAX filter type supported
*/
CMD_ADD_FILTER = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ENET, 58),
@@ -471,23 +475,133 @@ enum vnic_devcmd_cmd {
CMD_QP_STATS_CLEAR = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 63),
/*
- * Enable/Disable overlay offloads on the given vnic
+ * UEFI BOOT API: (u64)a0= UEFI FLS_CMD_xxx
+ * (ui64)a1= paddr for the info buffer
+ */
+ CMD_FC_REQ = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_FC, 64),
+
+ /*
+ * Return the iSCSI config details required by the EFI Option ROM
+ * in: (u32) a0=0 Get Boot Info for PXE eNIC as per pxe_boot_config_t
+ * a0=1 Get Boot info for iSCSI enic as per
+ * iscsi_boot_efi_cfg_t
+ * in: (u64) a1=Host address where iSCSI config info is returned
+ */
+ CMD_VNIC_BOOT_CONFIG_INFO = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ALL, 65),
+
+ /*
+ * Create a Queue Pair (RoCE)
+ * in: (u32) a0 = Queue Pair number
+ * (u32) a1 = Remote QP
+ * (u32) a2 = RDMA-RQ
+ * (u16) a3 = RQ Res Group
+ * (u16) a4 = SQ Res Group
+ * (u32) a5 = Protection Domain
+ * (u64) a6 = Remote MAC
+ * (u32) a7 = start PSN
+ * (u16) a8 = MSS
+ * (u32) a9 = protocol version
+ */
+ CMD_RDMA_QP_CREATE = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 66),
+
+ /*
+ * Delete a Queue Pair (RoCE)
+ * in: (u32) a0 = Queue Pair number
+ */
+ CMD_RDMA_QP_DELETE = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 67),
+
+ /*
+ * Retrieve a Queue Pair's status information (RoCE)
+ * in: (u32) a0 = Queue Pair number
+ * (u64) a1 = host buffer addr for QP status struct
+ * (u32) a2 = length of the buffer
+ */
+ CMD_RDMA_QP_STATUS = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ENET, 68),
+
+ /*
+ * Use this devcmd for agreeing on the highest common version supported
+ * by both driver and fw for by features who need such a facility.
+ * in: (u64) a0 = feature (driver requests for the supported versions
+ * on this feature)
+ * out: (u64) a0 = bitmap of all supported versions for that feature
+ */
+ CMD_GET_SUPP_FEATURE_VER = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ENET, 69),
+
+ /*
+ * Initialize the RDMA notification work queue
+ * in: (u64) a0 = host buffer address
+ * in: (u16) a1 = number of entries in buffer
+ * in: (u16) a2 = resource group number
+ * in: (u16) a3 = CQ number to post completion
+ */
+ CMD_RDMA_INIT_INFO_BUF = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 70),
+
+ /*
+ * De-init the RDMA notification work queue
+ * in: (u64) a0=resource group number
+ */
+ CMD_RDMA_DEINIT_INFO_BUF = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 71),
+
+ /*
+ * Control (Enable/Disable) overlay offloads on the given vnic
* in: (u8) a0 = OVERLAY_FEATURE_NVGRE : NVGRE
* a0 = OVERLAY_FEATURE_VXLAN : VxLAN
- * in: (u8) a1 = OVERLAY_OFFLOAD_ENABLE : Enable
- * a1 = OVERLAY_OFFLOAD_DISABLE : Disable
+ * in: (u8) a1 = OVERLAY_OFFLOAD_ENABLE : Enable or
+ * a1 = OVERLAY_OFFLOAD_DISABLE : Disable or
+ * a1 = OVERLAY_OFFLOAD_ENABLE_V2 : Enable with version 2
*/
- CMD_OVERLAY_OFFLOAD_ENABLE_DISABLE =
- _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 72),
+ CMD_OVERLAY_OFFLOAD_CTRL =
+ _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 72),
/*
* Configuration of overlay offloads feature on a given vNIC
- * in: (u8) a0 = DEVCMD_OVERLAY_NVGRE : NVGRE
- * a0 = DEVCMD_OVERLAY_VXLAN : VxLAN
- * in: (u8) a1 = VXLAN_PORT_UPDATE : VxLAN
- * in: (u16) a2 = unsigned short int port information
+ * in: (u8) a0 = OVERLAY_CFG_VXLAN_PORT_UPDATE : VxLAN
+ * in: (u16) a1 = unsigned short int port information
*/
CMD_OVERLAY_OFFLOAD_CFG = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 73),
+
+ /*
+ * Return the configured name for the device
+ * in: (u64) a0=Host address where the name is copied
+ * (u32) a1=Size of the buffer
+ */
+ CMD_GET_CONFIG_NAME = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ALL, 74),
+
+ /*
+ * Enable group interrupt for the VF
+ * in: (u32) a0 = GRPINTR_ENABLE : enable
+ * a0 = GRPINTR_DISABLE : disable
+ * a0 = GRPINTR_UPD_VECT: update group vector addr
+ * in: (u32) a1 = interrupt group count
+ * in: (u64) a2 = Start of host buffer address for DMAing group
+ * vector bitmap
+ * in: (u64) a3 = Stride between group vectors
+ */
+ CMD_CONFIG_GRPINTR = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 75),
+
+ /*
+ * Set cq arrary base and size in a list of consective wqs and
+ * rqs for a device
+ * in: (u16) a0 = the wq relative index in the device.
+ * -1 indicates skipping wq configuration
+ * in: (u16) a1 = the wcq relative index in the device
+ * in: (u16) a2 = the rq relative index in the device
+ * -1 indicates skipping rq configuration
+ * in: (u16) a3 = the rcq relative index in the device
+ */
+ CMD_CONFIG_CQ_ARRAY = _CMDC(_CMD_DIR_WRITE, _CMD_VTYPE_ENET, 76),
+
+ /*
+ * Add an advanced filter.
+ * in: (u64) a0= filter address
+ * (u32) a1= size of filter
+ * out: (u32) a0=filter identifier
+ *
+ * Capability query:
+ * out: (u64) a0= 1 if capabliity query supported
+ * (u64) a1= MAX filter type supported
+ */
+ CMD_ADD_ADV_FILTER = _CMDC(_CMD_DIR_RW, _CMD_VTYPE_ENET, 77),
};
/* CMD_ENABLE2 flags */
@@ -520,6 +634,9 @@ enum vnic_devcmd_status {
STAT_NONE = 0,
STAT_BUSY = 1 << 0, /* cmd in progress */
STAT_ERROR = 1 << 1, /* last cmd caused error (code in a0) */
+ STAT_FAILOVER = 1 << 2, /* always set on vnics in pci standby state
+ * if seen a failover to the standby happened
+ */
};
enum vnic_devcmd_error {
@@ -558,9 +675,9 @@ enum fwinfo_asic_type {
FWINFO_ASIC_TYPE_UNKNOWN,
FWINFO_ASIC_TYPE_PALO,
FWINFO_ASIC_TYPE_SERENO,
+ FWINFO_ASIC_TYPE_CRUZ,
};
-
struct vnic_devcmd_notify {
u32 csum; /* checksum over following words */
@@ -595,25 +712,16 @@ struct vnic_devcmd_provinfo {
*/
#define FILTER_FIELD_VALID(fld) (1 << (fld - 1))
-#define FILTER_FIELDS_USNIC (FILTER_FIELD_VALID(1) | \
- FILTER_FIELD_VALID(2) | \
- FILTER_FIELD_VALID(3) | \
- FILTER_FIELD_VALID(4))
-
-#define FILTER_FIELDS_IPV4_5TUPLE (FILTER_FIELD_VALID(1) | \
- FILTER_FIELD_VALID(2) | \
- FILTER_FIELD_VALID(3) | \
- FILTER_FIELD_VALID(4) | \
- FILTER_FIELD_VALID(5))
-
-#define FILTER_FIELDS_MAC_VLAN (FILTER_FIELD_VALID(1) | \
- FILTER_FIELD_VALID(2))
-
#define FILTER_FIELD_USNIC_VLAN FILTER_FIELD_VALID(1)
#define FILTER_FIELD_USNIC_ETHTYPE FILTER_FIELD_VALID(2)
#define FILTER_FIELD_USNIC_PROTO FILTER_FIELD_VALID(3)
#define FILTER_FIELD_USNIC_ID FILTER_FIELD_VALID(4)
+#define FILTER_FIELDS_USNIC (FILTER_FIELD_USNIC_VLAN | \
+ FILTER_FIELD_USNIC_ETHTYPE | \
+ FILTER_FIELD_USNIC_PROTO | \
+ FILTER_FIELD_USNIC_ID)
+
struct filter_usnic_id {
u32 flags;
u16 vlan;
@@ -628,10 +736,18 @@ struct filter_usnic_id {
#define FILTER_FIELD_5TUP_SRC_PT FILTER_FIELD_VALID(4)
#define FILTER_FIELD_5TUP_DST_PT FILTER_FIELD_VALID(5)
+#define FILTER_FIELDS_IPV4_5TUPLE (FILTER_FIELD_5TUP_PROTO | \
+ FILTER_FIELD_5TUP_SRC_AD | \
+ FILTER_FIELD_5TUP_DST_AD | \
+ FILTER_FIELD_5TUP_SRC_PT | \
+ FILTER_FIELD_5TUP_DST_PT)
+
/* Enums for the protocol field. */
enum protocol_e {
PROTO_UDP = 0,
PROTO_TCP = 1,
+ PROTO_IPV4 = 2,
+ PROTO_IPV6 = 3
};
struct filter_ipv4_5tuple {
@@ -646,12 +762,78 @@ struct filter_ipv4_5tuple {
#define FILTER_FIELD_VMQ_VLAN FILTER_FIELD_VALID(1)
#define FILTER_FIELD_VMQ_MAC FILTER_FIELD_VALID(2)
+#define FILTER_FIELDS_MAC_VLAN (FILTER_FIELD_VMQ_VLAN | \
+ FILTER_FIELD_VMQ_MAC)
+
+#define FILTER_FIELDS_NVGRE FILTER_FIELD_VMQ_MAC
+
struct filter_mac_vlan {
u32 flags;
u16 vlan;
u8 mac_addr[6];
} __attribute__((packed));
+#define FILTER_FIELD_VLAN_IP_3TUP_VLAN FILTER_FIELD_VALID(1)
+#define FILTER_FIELD_VLAN_IP_3TUP_L3_PROTO FILTER_FIELD_VALID(2)
+#define FILTER_FIELD_VLAN_IP_3TUP_DST_AD FILTER_FIELD_VALID(3)
+#define FILTER_FIELD_VLAN_IP_3TUP_L4_PROTO FILTER_FIELD_VALID(4)
+#define FILTER_FIELD_VLAN_IP_3TUP_DST_PT FILTER_FIELD_VALID(5)
+
+#define FILTER_FIELDS_VLAN_IP_3TUP (FILTER_FIELD_VLAN_IP_3TUP_VLAN | \
+ FILTER_FIELD_VLAN_IP_3TUP_L3_PROTO | \
+ FILTER_FIELD_VLAN_IP_3TUP_DST_AD | \
+ FILTER_FIELD_VLAN_IP_3TUP_L4_PROTO | \
+ FILTER_FIELD_VLAN_IP_3TUP_DST_PT)
+
+struct filter_vlan_ip_3tuple {
+ u32 flags;
+ u16 vlan;
+ u16 l3_protocol;
+ union {
+ u32 dst_addr_v4;
+ u8 dst_addr_v6[16];
+ } u;
+ u32 l4_protocol;
+ u16 dst_port;
+} __attribute__((packed));
+
+#define FILTER_GENERIC_1_BYTES 64
+
+enum filter_generic_1_layer {
+ FILTER_GENERIC_1_L2,
+ FILTER_GENERIC_1_L3,
+ FILTER_GENERIC_1_L4,
+ FILTER_GENERIC_1_L5,
+ FILTER_GENERIC_1_NUM_LAYERS
+};
+
+#define FILTER_GENERIC_1_IPV4 (1 << 0)
+#define FILTER_GENERIC_1_IPV6 (1 << 1)
+#define FILTER_GENERIC_1_UDP (1 << 2)
+#define FILTER_GENERIC_1_TCP (1 << 3)
+#define FILTER_GENERIC_1_TCP_OR_UDP (1 << 4)
+#define FILTER_GENERIC_1_IP4SUM_OK (1 << 5)
+#define FILTER_GENERIC_1_L4SUM_OK (1 << 6)
+#define FILTER_GENERIC_1_IPFRAG (1 << 7)
+
+#define FILTER_GENERIC_1_KEY_LEN 64
+
+/*
+ * Version 1 of generic filter specification
+ * position is only 16 bits, reserving positions > 64k to be used by firmware
+ */
+struct filter_generic_1 {
+ u16 position; /* lower position comes first */
+ u32 mask_flags;
+ u32 val_flags;
+ u16 mask_vlan;
+ u16 val_vlan;
+ struct {
+ u8 mask[FILTER_GENERIC_1_KEY_LEN]; /* 0 bit means "don't care"*/
+ u8 val[FILTER_GENERIC_1_KEY_LEN];
+ } __attribute__((packed)) layer[FILTER_GENERIC_1_NUM_LAYERS];
+} __attribute__((packed));
+
/* Specifies the filter_action type. */
enum {
FILTER_ACTION_RQ_STEERING = 0,
@@ -670,6 +852,10 @@ enum filter_type {
FILTER_USNIC_ID = 0,
FILTER_IPV4_5TUPLE = 1,
FILTER_MAC_VLAN = 2,
+ FILTER_VLAN_IP_3TUPLE = 3,
+ FILTER_NVGRE_VMQ = 4,
+ FILTER_USNIC_IP = 5,
+ FILTER_DPDK_1 = 6,
FILTER_MAX
};
@@ -679,6 +865,27 @@ struct filter {
struct filter_usnic_id usnic;
struct filter_ipv4_5tuple ipv4;
struct filter_mac_vlan mac_vlan;
+ struct filter_vlan_ip_3tuple vlan_3tuple;
+ } u;
+} __attribute__((packed));
+
+/*
+ * This is a strict superset of "struct filter" and exists only
+ * because many drivers use "sizeof (struct filter)" in deciding TLV size.
+ * This new, larger struct filter would cause any code that uses that method
+ * to not work with older firmware, so we add filter_v2 to hold the
+ * new filter types. Drivers should use vnic_filter_size() to determine
+ * the TLV size instead of sizeof (struct fiter_v2) to guard against future
+ * growth.
+ */
+struct filter_v2 {
+ u32 type;
+ union {
+ struct filter_usnic_id usnic;
+ struct filter_ipv4_5tuple ipv4;
+ struct filter_mac_vlan mac_vlan;
+ struct filter_vlan_ip_3tuple vlan_3tuple;
+ struct filter_generic_1 generic_1;
} u;
} __attribute__((packed));
@@ -687,14 +894,55 @@ enum {
CLSF_TLV_ACTION = 1,
};
-#define FILTER_MAX_BUF_SIZE 100 /* Maximum size of buffer to CMD_ADD_FILTER */
-
struct filter_tlv {
- uint32_t type;
- uint32_t length;
- uint32_t val[0];
+ u_int32_t type;
+ u_int32_t length;
+ u_int32_t val[0];
};
+/* Data for CMD_ADD_FILTER is 2 TLV and filter + action structs */
+#define FILTER_MAX_BUF_SIZE 100
+#define FILTER_V2_MAX_BUF_SIZE (sizeof(struct filter_v2) + \
+ sizeof(struct filter_action) + \
+ (2 * sizeof(struct filter_tlv)))
+
+/*
+ * Compute actual structure size given filter type. To be "future-proof,"
+ * drivers should use this instead of "sizeof (struct filter_v2)" when
+ * computing length for TLV.
+ */
+static inline u_int32_t
+vnic_filter_size(struct filter_v2 *fp)
+{
+ u_int32_t size;
+
+ switch (fp->type) {
+ case FILTER_USNIC_ID:
+ size = sizeof(fp->u.usnic);
+ break;
+ case FILTER_IPV4_5TUPLE:
+ size = sizeof(fp->u.ipv4);
+ break;
+ case FILTER_MAC_VLAN:
+ case FILTER_NVGRE_VMQ:
+ size = sizeof(fp->u.mac_vlan);
+ break;
+ case FILTER_VLAN_IP_3TUPLE:
+ size = sizeof(fp->u.vlan_3tuple);
+ break;
+ case FILTER_USNIC_IP:
+ case FILTER_DPDK_1:
+ size = sizeof(fp->u.generic_1);
+ break;
+ default:
+ size = sizeof(fp->u);
+ break;
+ }
+ size += sizeof(fp->type);
+ return size;
+}
+
+
enum {
CLSF_ADD = 0,
CLSF_DEL = 1,
@@ -766,8 +1014,30 @@ typedef enum {
OVERLAY_FEATURE_MAX,
} overlay_feature_t;
-#define OVERLAY_OFFLOAD_ENABLE 0
-#define OVERLAY_OFFLOAD_DISABLE 1
+#define OVERLAY_OFFLOAD_ENABLE 0
+#define OVERLAY_OFFLOAD_DISABLE 1
+#define OVERLAY_OFFLOAD_ENABLE_V2 2
#define OVERLAY_CFG_VXLAN_PORT_UPDATE 0
+
+/*
+ * Use this enum to get the supported versions for each of these features
+ * If you need to use the devcmd_get_supported_feature_version(), add
+ * the new feature into this enum and install function handler in devcmd.c
+ */
+typedef enum {
+ VIC_FEATURE_VXLAN,
+ VIC_FEATURE_RDMA,
+ VIC_FEATURE_MAX,
+} vic_feature_t;
+
+/*
+ * CMD_CONFIG_GRPINTR subcommands
+ */
+typedef enum {
+ GRPINTR_ENABLE = 1,
+ GRPINTR_DISABLE,
+ GRPINTR_UPD_VECT,
+} grpintr_subcmd_t;
+
#endif /* _VNIC_DEVCMD_H_ */
--
2.10.0
More information about the dev
mailing list