[dpdk-dev] [PATCH] net/mlx5: handle expected errno properly

Yongseok Koh yskoh at mellanox.com
Thu Aug 23 23:08:09 CEST 2018


On Thu, Aug 23, 2018 at 02:38:51PM +0800, Xiaoyu Min wrote:
> rte_errno is a per thread variable and is widely used as an
> error indicator, which means a function could affect
> other functions' results by setting rte_errno carelessly
> 
> During rxq setup, an EINVAL rte_errno is expected since
> the queues are not created yet
> So rte_errno is cleared when it is EINVAL as expected
> 
> Signed-off-by: Xiaoyu Min <jackmin at mellanox.com>
> ---
>  drivers/net/mlx5/mlx5_rxq.c | 20 +++++++++++++++-----
>  1 file changed, 15 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/net/mlx5/mlx5_rxq.c b/drivers/net/mlx5/mlx5_rxq.c
> index 1f7bfd4..e7056e8 100644
> --- a/drivers/net/mlx5/mlx5_rxq.c
> +++ b/drivers/net/mlx5/mlx5_rxq.c
> @@ -443,6 +443,7 @@
>  	struct mlx5_rxq_data *rxq = (*priv->rxqs)[idx];
>  	struct mlx5_rxq_ctrl *rxq_ctrl =
>  		container_of(rxq, struct mlx5_rxq_ctrl, rxq);
> +	int ret = 0;
>  
>  	if (!rte_is_power_of_2(desc)) {
>  		desc = 1 << log2above(desc);
> @@ -459,13 +460,21 @@
>  		rte_errno = EOVERFLOW;
>  		return -rte_errno;
>  	}
> -	if (!mlx5_rxq_releasable(dev, idx)) {
> +	ret = mlx5_rxq_releasable(dev, idx);
> +	if (!ret) {
>  		DRV_LOG(ERR, "port %u unable to release queue index %u",
>  			dev->data->port_id, idx);
>  		rte_errno = EBUSY;
>  		return -rte_errno;
> +	} else if (ret == -EINVAL) {
> +		/**
> +		 * on the first time, rx queue doesn't exist,
> +		 * so just ignore this error and reset rte_errno.
> +		 */
> +		rte_errno = 0;

Unless this function returns failure, the rte_errno will be ignored by caller
and caller shouldn't assume rte_errno has 0. Caller will assume it is garbage
data in case of success. So we can silently ignore this case. Does it cause any
issue in application side?


Thanks,
Yongseok

> +	} else {
> +		mlx5_rxq_release(dev, idx);
>  	}
> -	mlx5_rxq_release(dev, idx);
>  	rxq_ctrl = mlx5_rxq_new(dev, idx, desc, socket, conf, mp);
>  	if (!rxq_ctrl) {
>  		DRV_LOG(ERR, "port %u unable to allocate queue index %u",
> @@ -1543,11 +1552,12 @@ struct mlx5_rxq_ctrl *
>   * @param dev
>   *   Pointer to Ethernet device.
>   * @param idx
> - *   TX queue index.
> + *   RX queue index.
>   *
>   * @return
> - *   1 if the queue can be released, negative errno otherwise and rte_errno is
> - *   set.
> + *   1 if the queue can be released
> + *   0 if the queue can not be released
> + *   -EINVAL if the queue doesn't exist
>   */
>  int
>  mlx5_rxq_releasable(struct rte_eth_dev *dev, uint16_t idx)
> -- 
> 1.8.3.1
> 


More information about the dev mailing list