[dpdk-dev] [PATCH v4 1/9] examples/ipsec-secgw: avoid to request unused TX offloads

[Akhil Goyal]

On 12/21/2018 9:28 PM, Ananyev, Konstantin wrote:
>
>> -----Original Message-----
>> From: Akhil Goyal [mailto:akhil.goyal at nxp.com]
>> Sent: Friday, December 21, 2018 1:57 PM
>> To: Ananyev, Konstantin <konstantin.ananyev at intel.com>; dev at dpdk.org
>> Cc: Nicolau, Radu <radu.nicolau at intel.com>; Horton, Remy <remy.horton at intel.com>
>> Subject: Re: [dpdk-dev] [PATCH v4 1/9] examples/ipsec-secgw: avoid to request unused TX offloads
>>
>> Hi Konstantin,
>>
>> On 12/14/2018 10:10 PM, Konstantin Ananyev wrote:
>>> ipsec-secgw always enables TX offloads
>>> (DEV_TX_OFFLOAD_MULTI_SEGS, DEV_TX_OFFLOAD_SECURITY),
>>> even when they are not requested by the config.
>>> That causes many PMD to choose full-featured TX function,
>>> which in many cases is much slower then one without offloads.
>>> That patch adds checks to enabled extra HW offloads, only when
>>> they were requested.
>>> Plus it enables DEV_TX_OFFLOAD_IPV4_CKSUM,
>>> only when other HW TX ofloads are going to be enabled.
>>> Otherwise SW version of ip cksum calculation is used.
>>> That allows to use vector TX function, when inline-ipsec is not
>>> requested.
>>>
>>> Signed-off-by: Remy Horton <remy.horton at intel.com>
>>> Signed-off-by: Konstantin Ananyev <konstantin.ananyev at intel.com>
>>> Acked-by: Radu Nicolau <radu.nicolau at intel.com>
>>> ---
>>>    examples/ipsec-secgw/ipsec-secgw.c | 44 +++++++++++++++--------
>>>    examples/ipsec-secgw/ipsec.h       |  6 ++++
>>>    examples/ipsec-secgw/sa.c          | 56 ++++++++++++++++++++++++++++++
>>>    3 files changed, 91 insertions(+), 15 deletions(-)
>>>
>>> diff --git a/examples/ipsec-secgw/ipsec-secgw.c b/examples/ipsec-secgw/ipsec-secgw.c
>>> index 1bc0b5b50..cfc2b05e5 100644
>>> --- a/examples/ipsec-secgw/ipsec-secgw.c
>>> +++ b/examples/ipsec-secgw/ipsec-secgw.c
>>> @@ -208,8 +208,6 @@ static struct rte_eth_conf port_conf = {
>>>    	},
>>>    	.txmode = {
>>>    		.mq_mode = ETH_MQ_TX_NONE,
>>> -		.offloads = (DEV_TX_OFFLOAD_IPV4_CKSUM |
>>> -			     DEV_TX_OFFLOAD_MULTI_SEGS),
>> I believe this is disabling checksum offload for all cases and then
>> enabling only for inline crypto and inline proto.
> Yes.
>
>> This is breaking lookaside proto and lookaside none cases. Please
>> correct me if I am wrong.
> Why breaking?
reduction in performance is kind of breaking the code.
> For cases when HW cksum offload is disabled, IPv4 cksum calculation
> will be done in SW, see below:
> prepare_tx_pkt(...)
> {
>     ...
>      +
>      +		/* calculate IPv4 cksum in SW */
>      +		if ((pkt->ol_flags & PKT_TX_IP_CKSUM) == 0)
>      +			ip->ip_sum = rte_ipv4_cksum((struct ipv4_hdr *)ip);
>
>
> We tested lookaside-none case quite extensively - all works well,
> in fact on Intel NICs it became even a bit faster because of that change
> (though not much).
yes, it may work well on one hardware, but may not perform good in other 
hardware where cores are limited.
> Disabling HW offloads when they are not really required has 2 benefits:
>   1) allows app to be run on NICs without HW offloads support.
>   2) allows dev_configure() for TX path to select simple/vector TX functions
>       which for many NICs are significantly faster.
>
> Konstantin
>
>> So a NACK for this if my understanding is correct.
>>