[dpdk-dev] [PATCH 2/7] net/mlx5: remove redundant objects in probe code
Xueming(Steven) Li
xuemingl at mellanox.com
Sun Jun 10 13:00:59 CEST 2018
Ack. Trivial issue related to other patch found , not sure whether it good to fix it here.
> -----Original Message-----
> From: dev <dev-bounces at dpdk.org> On Behalf Of Adrien Mazarguil
> Sent: Saturday, May 26, 2018 12:35 AM
> To: Shahaf Shuler <shahafs at mellanox.com>
> Cc: dev at dpdk.org
> Subject: [dpdk-dev] [PATCH 2/7] net/mlx5: remove redundant objects in probe code
>
> This patch gets rid of redundant calls to open the device and query its attributes in order to
> simplify the code.
>
> Signed-off-by: Adrien Mazarguil <adrien.mazarguil at 6wind.com>
> ---
> drivers/net/mlx5/mlx5.c | 60 +++++++++++++++++++++-----------------------
> 1 file changed, 28 insertions(+), 32 deletions(-)
>
> diff --git a/drivers/net/mlx5/mlx5.c b/drivers/net/mlx5/mlx5.c index 602f952ca..41a542ebc 100644
> --- a/drivers/net/mlx5/mlx5.c
> +++ b/drivers/net/mlx5/mlx5.c
> @@ -652,10 +652,10 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused, {
> struct ibv_device **list = NULL;
> struct ibv_device *ibv_dev;
> + struct ibv_context *ctx = NULL;
> + struct ibv_device_attr_ex attr;
> struct mlx5dv_context dv_attr = { .comp_mask = 0 };
> int err = 0;
> - struct ibv_context *attr_ctx = NULL;
> - struct ibv_device_attr_ex device_attr;
> unsigned int vf = 0;
> unsigned int mps;
> unsigned int cqe_comp;
> @@ -712,12 +712,12 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> PCI_DEVICE_ID_MELLANOX_CONNECTX5VF) ||
> (pci_dev->id.device_id ==
> PCI_DEVICE_ID_MELLANOX_CONNECTX5EXVF));
> - attr_ctx = mlx5_glue->open_device(list[i]);
> + ctx = mlx5_glue->open_device(list[i]);
> rte_errno = errno;
> err = rte_errno;
> break;
> }
> - if (attr_ctx == NULL) {
> + if (ctx == NULL) {
> switch (err) {
> case 0:
> DRV_LOG(ERR,
> @@ -820,23 +820,20 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> DRV_LOG(WARNING, "MPLS over GRE/UDP tunnel offloading disabled due to"
> " old OFED/rdma-core version or firmware configuration"); #endif
> - err = mlx5_glue->query_device_ex(attr_ctx, NULL, &device_attr);
> + err = mlx5_glue->query_device_ex(ctx, NULL, &attr);
> if (err) {
> DEBUG("ibv_query_device_ex() failed");
> goto error;
> }
> - DRV_LOG(INFO, "%u port(s) detected",
> - device_attr.orig_attr.phys_port_cnt);
> - for (i = 0; i < device_attr.orig_attr.phys_port_cnt; i++) {
> + DRV_LOG(INFO, "%u port(s) detected", attr.orig_attr.phys_port_cnt);
> + for (i = 0; i < attr.orig_attr.phys_port_cnt; i++) {
> char name[RTE_ETH_NAME_MAX_LEN];
> int len;
> uint32_t port = i + 1; /* ports are indexed from one */
> - struct ibv_context *ctx = NULL;
> struct ibv_port_attr port_attr;
> struct ibv_pd *pd = NULL;
> struct priv *priv = NULL;
> struct rte_eth_dev *eth_dev = NULL;
> - struct ibv_device_attr_ex device_attr_ex;
> struct ether_addr mac;
> struct mlx5_dev_config config = {
> .cqe_comp = cqe_comp,
> @@ -863,7 +860,7 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> len = snprintf(name, sizeof(name), PCI_PRI_FMT,
> pci_dev->addr.domain, pci_dev->addr.bus,
> pci_dev->addr.devid, pci_dev->addr.function);
> - if (device_attr.orig_attr.phys_port_cnt > 1)
> + if (attr.orig_attr.phys_port_cnt > 1)
> snprintf(name + len, sizeof(name), " port %u", i);
> if (rte_eal_process_type() == RTE_PROC_SECONDARY) {
> eth_dev = rte_eth_dev_attach_secondary(name);
> @@ -905,7 +902,8 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> continue;
> }
> DRV_LOG(DEBUG, "using port %u", port);
> - ctx = mlx5_glue->open_device(ibv_dev);
> + if (!ctx)
> + ctx = mlx5_glue->open_device(ibv_dev);
> if (ctx == NULL) {
> err = ENODEV;
> goto port_error;
> @@ -947,7 +945,7 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> priv->ctx = ctx;
> strncpy(priv->ibdev_path, priv->ctx->device->ibdev_path,
> sizeof(priv->ibdev_path));
> - priv->device_attr = device_attr;
> + priv->device_attr = attr;
> priv->port = port;
> priv->pd = pd;
> priv->mtu = ETHER_MTU;
> @@ -958,17 +956,12 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> strerror(rte_errno));
> goto port_error;
> }
> - err = mlx5_glue->query_device_ex(ctx, NULL, &device_attr_ex);
> - if (err) {
> - DRV_LOG(ERR, "ibv_query_device_ex() failed");
> - goto port_error;
> - }
> - config.hw_csum = !!(device_attr_ex.device_cap_flags_ex &
> + config.hw_csum = !!(attr.device_cap_flags_ex &
> IBV_DEVICE_RAW_IP_CSUM);
> DRV_LOG(DEBUG, "checksum offloading is %ssupported",
> (config.hw_csum ? "" : "not "));
> #ifdef HAVE_IBV_DEVICE_COUNTERS_SET_SUPPORT
> - config.flow_counter_en = !!(device_attr.max_counter_sets);
> + config.flow_counter_en = !!attr.max_counter_sets;
> mlx5_glue->describe_counter_set(ctx, 0, &cs_desc);
> DRV_LOG(DEBUG,
> "counter type = %d, num of cs = %ld, attributes = %d", @@ -976,7 +969,7 @@
> mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> cs_desc.attributes);
> #endif
> config.ind_table_max_size =
> - device_attr_ex.rss_caps.max_rwq_indirection_table_size;
> + attr.rss_caps.max_rwq_indirection_table_size;
> /* Remove this check once DPDK supports larger/variable
> * indirection tables. */
> if (config.ind_table_max_size >
> @@ -984,29 +977,28 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> config.ind_table_max_size = ETH_RSS_RETA_SIZE_512;
> DRV_LOG(DEBUG, "maximum Rx indirection table size is %u",
> config.ind_table_max_size);
> - config.hw_vlan_strip = !!(device_attr_ex.raw_packet_caps &
> + config.hw_vlan_strip = !!(attr.raw_packet_caps &
> IBV_RAW_PACKET_CAP_CVLAN_STRIPPING);
> DRV_LOG(DEBUG, "VLAN stripping is %ssupported",
> (config.hw_vlan_strip ? "" : "not "));
>
> - config.hw_fcs_strip = !!(device_attr_ex.raw_packet_caps &
> + config.hw_fcs_strip = !!(attr.raw_packet_caps &
> IBV_RAW_PACKET_CAP_SCATTER_FCS);
> DRV_LOG(DEBUG, "FCS stripping configuration is %ssupported",
> (config.hw_fcs_strip ? "" : "not "));
>
> #ifdef HAVE_IBV_WQ_FLAG_RX_END_PADDING
> - config.hw_padding = !!device_attr_ex.rx_pad_end_addr_align;
> + config.hw_padding = !!attr.rx_pad_end_addr_align;
> #endif
> DRV_LOG(DEBUG,
> "hardware Rx end alignment padding is %ssupported",
> (config.hw_padding ? "" : "not "));
> config.vf = vf;
> - config.tso = ((device_attr_ex.tso_caps.max_tso > 0) &&
> - (device_attr_ex.tso_caps.supported_qpts &
> + config.tso = (attr.tso_caps.max_tso > 0 &&
> + (attr.tso_caps.supported_qpts &
> (1 << IBV_QPT_RAW_PACKET)));
Not related to this patch, wrong indent.
> if (config.tso)
> - config.tso_max_payload_sz =
> - device_attr_ex.tso_caps.max_tso;
> + config.tso_max_payload_sz = attr.tso_caps.max_tso;
> if (config.mps && !mps) {
> DRV_LOG(ERR,
> "multi-packet send not supported on this device"
> @@ -1153,14 +1145,18 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> priv, mem_event_cb);
> rte_rwlock_write_unlock(&mlx5_shared_data->mem_event_rwlock);
> rte_eth_dev_probing_finish(eth_dev);
> + /*
> + * Each eth_dev instance is assigned its own Verbs context,
> + * since this one is consumed, let the next iteration open
> + * another.
> + */
> + ctx = NULL;
> continue;
> port_error:
> if (priv)
> rte_free(priv);
> if (pd)
> claim_zero(mlx5_glue->dealloc_pd(pd));
> - if (ctx)
> - claim_zero(mlx5_glue->close_device(ctx));
> if (eth_dev && rte_eal_process_type() == RTE_PROC_PRIMARY)
> rte_eth_dev_release_port(eth_dev);
> break;
> @@ -1172,8 +1168,8 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
> * way to enumerate the registered ethdevs to free the previous ones.
> */
> error:
> - if (attr_ctx)
> - claim_zero(mlx5_glue->close_device(attr_ctx));
> + if (ctx)
> + claim_zero(mlx5_glue->close_device(ctx));
> if (list)
> mlx5_glue->free_device_list(list);
> if (err) {
> --
> 2.11.0
More information about the dev
mailing list