[dpdk-dev] [PATCH 1/1] eal: Don't fail secondary if primary is missing tailqs

Luca Boccassi bluca at debian.org
Thu Nov 15 18:05:16 CET 2018


On Thu, 2018-11-15 at 17:01 +0000, Richardson, Bruce wrote:
> > -----Original Message-----
> > From: Burdick, Cliff [mailto:Cliff.Burdick at viasat.com]
> > Sent: Thursday, November 15, 2018 4:55 PM
> > To: Richardson, Bruce <bruce.richardson at intel.com>
> > Cc: Luca Boccassi <bluca at debian.org>; Thomas Monjalon
> > <thomas at monjalon.net>; Burakov, Anatoly <anatoly.burakov at intel.com>
> > ;
> > dev at dpdk.org
> > Subject: RE: [dpdk-dev] [PATCH 1/1] eal: Don't fail secondary if
> > primary
> > is missing tailqs
> > 
> > 
> > 
> > -----Original Message-----
> > From: Bruce Richardson [mailto:bruce.richardson at intel.com]
> > Sent: Thursday, November 15, 2018 8:41 AM
> > To: Burdick, Cliff
> > Cc: Luca Boccassi; Thomas Monjalon; Burakov, Anatoly; dev at dpdk.org
> > Subject: Re: [dpdk-dev] [PATCH 1/1] eal: Don't fail secondary if
> > primary
> > is missing tailqs
> > 
> > > On Thu, Nov 15, 2018 at 04:15:36PM +0000, Burdick, Cliff wrote:
> > > > 
> > > > 
> > > > -----Original Message-----
> > > > From: Luca Boccassi [mailto:bluca at debian.org]
> > > > Sent: Thursday, November 15, 2018 1:33 AM
> > > > To: Burdick, Cliff; Bruce Richardson
> > > > Cc: Thomas Monjalon; Burakov, Anatoly; dev at dpdk.org
> > > > Subject: Re: [dpdk-dev] [PATCH 1/1] eal: Don't fail secondary
> > > > if
> > > > primary is missing tailqs
> > > > 
> > > > > On Wed, 2018-11-14 at 18:24 +0000, Burdick, Cliff wrote:
> > > > > > 
> > > > > > -----Original Message-----
> > > > > > From: Luca Boccassi [mailto:bluca at debian.org]
> > > > > > Sent: Wednesday, November 14, 2018 10:15 AM
> > > > > > To: Burdick, Cliff; Bruce Richardson
> > > > > > Cc: Thomas Monjalon; Burakov, Anatoly; dev at dpdk.org
> > > > > > Subject: Re: [dpdk-dev] [PATCH 1/1] eal: Don't fail
> > > > > > secondary if
> > > > > > primary is missing tailqs
> > > > > > 
> > > > > > > On Wed, 2018-11-14 at 17:40 +0000, Burdick, Cliff wrote:
> > > > > > > > 
> > > > > > > > -----Original Message-----
> > > > > > > > From: Bruce Richardson [mailto:bruce.richardson at intel.c
> > > > > > > > om]
> > > > > > > > Sent: Wednesday, November 14, 2018 3:48 AM
> > > > > > > > To: Burdick, Cliff
> > > > > > > > Cc: Thomas Monjalon; Burakov, Anatoly; dev at dpdk.org
> > > > > > > > Subject: Re: [dpdk-dev] [PATCH 1/1] eal: Don't fail
> > > > > > > > secondary
> > > > > > > > if primary is missing tailqs
> > > > > > > > 
> > > > > > > > On Tue, Nov 13, 2018 at 11:42:51PM +0000, Burdick,
> > > > > > > > Cliff
> > 
> > wrote:
> > > > > > > > > > 
> > > > > > > > > > ________________________________________
> > > > > > > > > > From: Thomas Monjalon [thomas at monjalon.net]
> > > > > > > > > > Sent: Tuesday, November 13, 2018 2:18 PM
> > > > > > > > > > To: Burdick, Cliff
> > > > > > > > > > Cc: Burakov, Anatoly; dev at dpdk.org;
> > > > > > > > > > bruce.richardson at intel.co m
> > > > > > > > > > Subject: Re: [dpdk-dev] [PATCH 1/1] eal: Don't fail
> > > > > > > > > > secondary if primary is missing tailqs
> > > > > > > > > > 
> > > > > > > > > > 13/11/2018 23:08, Burdick, Cliff:
> > > > > > > > > > > From: Thomas Monjalon [mailto:thomas at monjalon.net
> > > > > > > > > > > ]
> > > > > > > > > > > > 13/11/2018 17:38, Burdick, Cliff:
> > > > > > > > > > > > > From: Thomas Monjalon [mailto:thomas at monjalon
> > > > > > > > > > > > > .net]
> > > > > > > > > > > > > 13/11/2018 16:45, Burdick, Cliff:
> > > > > > > > > > > > > > From: Burakov, Anatoly
> > 
> > [mailto:anatoly.burakov at intel.
> > > > > > > > > > > > > > com]
> > > > > > > > > > > > > > > On 13-Nov-18 9:21 AM, Thomas Monjalon
> > > > > > > > > > > > > > > wrote:
> > > > > > > > > > > > > > > > 13/11/2018 00:33, Burdick, Cliff:
> > > > > > > > > > > > > > > > > This patch was submitted by Jean
> > > > > > > > > > > > > > > > > Tourrilhes
> > > > > > > > > > > > > > > > > over two years ago, but didn't
> > > > > > > > > > > > > > > > > receive any
> > 
> > responses.
> > > > > > > > > > > > > > > > > I hit the same issue recently when
> > > > > > > > > > > > > > > > > trying to
> > > > > > > > > > > > > > > > > use cgo
> > > > > > > > > > > > > > > > > (Golang) as a primary process linked
> > > > > > > > > > > > > > > > > to
> > > > > > > > > > > > > > > > > libdpdk.a against a C++ application
> > > > > > > > > > > > > > > > > linked
> > > > > > > > > > > > > > > > > against the same library.> > >
> > > > > > > > > > > > > > > > 
> > > > > > > > > > > > > > > > The question is to know why you don't
> > > > > > > > > > > > > > > > have the
> > > > > > > > > > > > > > > > same constructors in primary and
> > > > > > > > > > > > > > > > seconday?
> > > > > > > > > > > > > > > 
> > > > > > > > > > > > > > > I've hit similar things in the past. I
> > > > > > > > > > > > > > > believe
> > > > > > > > > > > > > > > it was caused by our build system
> > > > > > > > > > > > > > > stripping out
> > > > > > > > > > > > > > > unused libraries (such as
> > > > > > > > > > > > > > > rte_hash) from the binary and thus not
> > > > > > > > > > > > > > > calling
> > > > > > > > > > > > > > > the constructor in the primary, but doing
> > > > > > > > > > > > > > > so in
> > > > > > > > > > > > > > > the secondary (or something to that
> > > > > > > > > > > > > > > effect). In
> > > > > > > > > > > > > > > any case, this is caused by linking
> > > > > > > > > > > > > > > different
> > > > > > > > > > > > > > > number of libraries to primary and
> > > > > > > > > > > > > > > secondary,
> > > > > > > > > > > > > > > and should probably be fixed in the build
> > > > > > > > > > > > > > > system, not in the tailqs code (unless we
> > > > > > > > > > > > > > > specifically support having different
> > > > > > > > > > > > > > > linked
> > > > > > > > > > > > > > > libraries to primary and secondary?).> >
> > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > 
> > > > > > > > > > > > > > Right, I think the original author of the
> > > > > > > > > > > > > > patch
> > > > > > > > > > > > > > stated the reasons in the link I provided.
> > > > > > > > > > > > > > The
> > > > > > > > > > > > > > build system seems like the most
> > > > > > > > > > > > > > appropriate place
> > > > > > > > > > > > > > to fix it, but the patch got me going
> > > > > > > > > > > > > > quickly. I
> > > > > > > > > > > > > > think the question is whether you want DPDK
> > > > > > > > > > > > > > to
> > > > > > > > > > > > > > support these other ways of linking.
> > > > > > > > > > > > > > I'm
> > > > > > > > > > > > > > certainly not the first to use cgo, since
> > > > > > > > > > > > > > there's
> > > > > > > > > > > > > > a virtual switch project doing the same:
> > > > > > > > > > > > > > 
> > > > > > > > > > > > > > https://urldefense.proofpoint.com/v2/url?u=
> > > > > > > > > > > > > > https-3
> > > > > > > > > > > > > > A__
> > > > > > > > > > > > > > gith
> > > > > > > > > > > > > > ub.co
> > > > > > > > > > > > > > m_lago
> > > > > > > > > > > > > > pu
> > > > > > > > > > > > > > s_vsw&d=DwICAg&c=jcv3orpCsv7C4ly8-
> > > > > > > > > > > > > > ubDoUfrxF5xIGWmptxGWP5vi5w&r =m1RLQ OG
> > > > > > > > > > > > > > Okz9MauvVLZmiGtyWc5mA7DejbPFNE1IDj-
> > > > > > > > > > > > > > 4&m=hQqVCNwW7eoEzB_hLFK97i8 idS8FI qX
> > > > > > > > > > > > > > oPeclwsIZq7Y&s=BMoBlwkqljwWIBY3SE3pPMCfVnOU
> > > > > > > > > > > > > > lDuZLrn
> > > > > > > > > > > > > > o4-
> > > > > > > > > > > > > > SojKM&e=
> > > > > > > > > > > > > > 
> > > > > > > > > > > > > > They don't use primary/secondary processes,
> > > > > > > > > > > > > > though, so the issue is  never hit. I'm in
> > > > > > > > > > > > > > a
> > > > > > > > > > > > > > situation where using cgo seemed like the
> > > > > > > > > > > > > > easiest
> > > > > > > > > > > > > > path to accomplish what I'm doing since I
> > > > > > > > > > > > > > needed
> > > > > > > > > > > > > > specialized  libraries for it that were not
> > > > > > > > > > > > > > available in C/C++. At some point I  bet
> > > > > > > > > > > > > > someone
> > > > > > > > > > > > > > would use Cython to start linking against
> > > > > > > > > > > > > > DPDK as
> > > > > > > > > > > > > > well,  and we'd likely run into the same
> > > > > > > > > > > > > > issue.> >
> > > > > > > > > > > > > > > > For sure, we want to support using DPDK
> > > > > > > > > > > > > > > > with
> > 
> > cgo or cython.
> > > > > > > > > > > > > > But it is not clear what is the relation
> > > > > > > > > > > > > > with not
> > > > > > > > > > > > > > having the same compilation for primary and
> > 
> > secondary.
> > > > > > > > > > > > > > Please
> > > > > > > > > > > > > > could you elaborate?> > >
> > > > > > > > > > > > > 
> > > > > > > > > > > > > Hi Thomas, I think Jean explained it well
> > > > > > > > > > > > > here:
> > > > > > > > > > > > > https://urldefense.proofpoint.com/v2/url?u=ht
> > > > > > > > > > > > > tps-3A_
> > > > > > > > > > > > > _de
> > > > > > > > > > > > > v.dp
> > > > > > > > > > > > > dk.narkive.
> > > > > > > > > > > > > com_ZM3a7QD1_dpdk-2Ddev-2Dbug-2Dstatic-
> > > > > > > > > > > > > 2Dconstructor
> > > > > > > > > > > > > s-
> > > > > > > > > > > > > 2Dconsider
> > > > > > > > > > > > > ed-2De
> > > > > > > > > > > > > vil&d=DwICAg&c=jcv3orpCsv7C4ly8-
> > > > > > > > > > > > > ubDoUfrxF5xIGWmptxGWP5vi5w&r=m1R LQOGOk
> > > > > > > > > > > > > z9MauvVLZmiGtyWc5mA7DejbPFNE1IDj-
> > > > > > > > > > > > > 4&m=C69wDgrjDX8_oXp1M_3bnmWOOZd GqwBBG
> > > > > > > > > > > > > 9vzkyGDWGQ&s=YYn2N7WrzJpH1ptNrLZad0nPAQdrUyqB
> > > > > > > > > > > > > ckk2uFu
> > > > > > > > > > > > > WYP
> > > > > > > > > > > > > Q&e=
> > > > > > > > > > > > > 
> > > > > > > > > > > > > "The build system of the application does not
> > > > > > > > > > > > > have
> > > > > > > > > > > > > all the subtelties of the DPDK build system,
> > > > > > > > > > > > > and
> > > > > > > > > > > > > ends up including
> > > > > > > > > > > > > *all*
> > > > > > > > > > > > > the constructors, wether they are used or not
> > > > > > > > > > > > > in the
> > > > > > > > > > > > > code.
> > > > > > > > > > > > > Moreover, they are included in a different
> > > > > > > > > > > > > order.
> > > > > > > > > > > > > Actually,
> > > > > > > > > > > > > by default the builds include no constructors
> > > > > > > > > > > > > at all
> > > > > > > > > > > > > (which is a big fail), so the library needs
> > > > > > > > > > > > > to be
> > > > > > > > > > > > > included with --whole-archive (see Snort DPDK
> > > > > > > > > > > > > instructions)."
> > > > > > > > > > > > > 
> > > > > > > > > > > > > I will get to the bottom of my exact case to
> > > > > > > > > > > > > understand what's happening, but my primary
> > > > > > > > > > > > > application is a cgo application that I'm
> > > > > > > > > > > > > linking to
> > > > > > > > > > > > > by using almost exactly the same flags that
> > > > > > > > > > > > > are used
> > > > > > > > > > > > > in the DPDK build system to build examples.
> > > > > > > > > > > > > The DPDK
> > > > > > > > > > > > > libraries I'm linking against is a single
> > > > > > > > > > > > > location
> > > > > > > > > > > > > for both primary and secondary; in other
> > > > > > > > > > > > > words, I
> > 
> > don't build DPDK twice.
> > > > > > > > > > > > > 
> > > > > > > > > > > > > OK I understand, thanks.
> > > > > > > > > > > > > 
> > > > > > > > > > > > > You had alluded to a pkg-config for DPDK in
> > > > > > > > > > > > > the 2015
> > > > > > > > > > > > > thread, which cgo can use, but I don't know
> > > > > > > > > > > > > if that
> > > > > > > > > > > > > ever was implemented. Cgo can use pkg-config
> > > > > > > > > > > > > if it's
> > > > > > > > > > > > > available, otherwise the only tools are
> > > > > > > > > > > > > specifying
> > > > > > > > > > > > > LDFLAGS and CFLAGS into their build system.
> > > > > > > > > > > > 
> > > > > > > > > > > > Yes, the right answer is still pkg-config :)
> > > > > > > > > > > > The good
> > > > > > > > > > > > news is that it is now implemented thanks to
> > > > > > > > > > > > the meson
> > > > > > > > > > > > build
> > > > > > > > > > > > system:
> > > > > > > > > > > > 
> > > > > > > > > > > > https://urldefense.proofpoint.com/v2/url?u=http
> > > > > > > > > > > > -3A__gi
> > > > > > > > > > > > t.d
> > > > > > > > > > > > pdk.
> > > > > > > > > > > > org_dp
> > > > > > > > > > > > dk_tree_doc_build-2Dsdk-2Dmeson.txt-
> > > > > > > > > > > > 23n182&d=DwICAg&c=jcv3orpCsv7C4
> > > > > > > > > > > > ly8-
> > > > > > > > > > > > ubDoUfrxF5xIGWmptxGWP5vi5w&r=m1RLQOGOkz9MauvVLZ
> > > > > > > > > > > > miGtyWc
> > > > > > > > > > > > 5mA
> > > > > > > > > > > > 7Dej
> > > > > > > > > > > > bP
> > > > > > > > > > > > FNE1IDj-
> > > > > > > > > > > > > 4&m=C69wDgrjDX8_oXp1M_3bnmWOOZdGqwBBG9vzkyGDW
> > > > > > > > > > > > > GQ&s=oC
> > > > > > > > > > > > > 86K
> > > > > > > > > > > > > D_R
> > > > > > > > > > > > 
> > > > > > > > > > > > J1T6rfzi3x5zFT1Ri13ELpKmsyFqpgDbgFg&e=
> > > > > > > > > > > 
> > > > > > > > > > > Hi Thomas, are there instructions on how to use
> > > > > > > > > > > pkg-config to build the mlx4/5 PMD? I noticed a
> > > > > > > > > > > patch
> > > > > > > > > > > was submitted in September to add support for it,
> > > > > > > > > > > but
> > > > > > > > > > > that link you provided on using meson doesn't say
> > > > > > > > > > > how to
> > > > > > > > > > > build specific drivers. It appears to be disabled
> > > > > > > > > > > by
> > 
> > default.
> > > > > > > > > > > If the dependency is found, meson will enable the
> > > > > > > > > > > PMD
> > > > > > > > > > > when building DPDK.
> > > > > > > > > > 
> > > > > > > > > > Do you know where exactly that is? I've been using
> > > > > > > > > > mlx5
> > > > > > > > > > for a while on this system, and I can see that
> > > > > > > > > > 18.11-rc2
> > > > > > > > > > meson
> > > > > > > > > > build+ninja built the pmd, but it's not on the --
> > > > > > > > > > libs
> > > > > > > > > > build+listing
> > > > > > > > > > for
> > > > > > > > > > pkg-config. Does it tell me what I was missing?
> > > > > > > > > > 
> > > > > > > > > 
> > > > > > > > > For dynamic linking of applications, the drivers are
> > > > > > > > > not
> > > > > > > > > normally linked in. Instead, they should be loaded
> > > > > > > > > from the
> > > > > > > > > drivers directory as .so files
> > > > > > > > > - normally by default in EAL as the driver .so's
> > > > > > > > > should be
> > > > > > > > > copied to the EAL_PMD_PATH where EAL finds them
> > 
> > automatically.
> > > > > > > > > [This applies to both meson and make builds, though
> > > > > > > > > only
> > > > > > > > > meson generates the .pc file for pkg-config]
> > > > > > > > > 
> > > > > > > > > If you are doing a static build, then you need to
> > > > > > > > > explicitly
> > > > > > > > > link in the drivers. You can get a list from pkg-
> > > > > > > > > config
> > > > > > > > > using the "
> > > > > > > > > --static" flag in this case. A good example of how to
> > > > > > > > > use
> > > > > > > > > pkg- config in this way can be found in the Makefiles
> > > > > > > > > for
> > > > > > > > > most examples, e.g. examples/helloworld/Makefile,
> > > > > > > > > reproduced
> > 
> > below.
> > > > > > > > > 
> > > > > > > > > Regards,
> > > > > > > > > /Bruce
> > > > > > > > > 
> > > > > > > > > all: shared
> > > > > > > > > .PHONY: shared static
> > > > > > > > > shared: build/$(APP)-shared
> > > > > > > > >         ln -sf $(APP)-shared build/$(APP)
> > > > > > > > > static: build/$(APP)-static
> > > > > > > > >         ln -sf $(APP)-static build/$(APP)
> > > > > > > > > 
> > > > > > > > > PC_FILE := $(shell pkg-config --path libdpdk) CFLAGS
> > > > > > > > > += -O3
> > > > > > > > > $(shell pkg-config --cflags libdpdk) LDFLAGS_SHARED =
> > > > > > > > > $(shell
> > > > > > > > > pkg- config -- libs libdpdk) LDFLAGS_STATIC = -Wl,-
> > > > > > > > > Bstatic
> > > > > > > > > $(shell pkg-config
> > > > > > > > > --
> > > > > > > > > static --libs libdpdk)
> > > > > > > > > 
> > > > > > > > > build/$(APP)-shared: $(SRCS-y) Makefile $(PC_FILE) |
> > > > > > > > > build
> > > > > > > > >         $(CC) $(CFLAGS) $(SRCS-y) -o $@ $(LDFLAGS)
> > > > > > > > > $(LDFLAGS_SHARED)
> > > > > > > > > 
> > > > > > > > > build/$(APP)-static: $(SRCS-y) Makefile $(PC_FILE) |
> > > > > > > > > build
> > > > > > > > >         $(CC) $(CFLAGS) $(SRCS-y) -o $@ $(LDFLAGS)
> > > > > > > > > $(LDFLAGS_STATIC)
> > > > > > > > > 
> > > > > > > > > build:
> > > > > > > > >         @mkdir -p $@
> > > > > > > > 
> > > > > > > > Thanks Bruce. I tried getting this to compile using
> > > > > > > > cgo, and
> > > > > > > > it's causing more pain than it's worth. I used the --
> > > > > > > > static
> > > > > > > > --libs options, and there were still numerous linker
> > > > > > > > errors,
> > > > > > > > some specific to mlx, and some not. Specifically
> > > > > > > > libmlx5 and
> > > > > > > > libmnl are both needed, but they're not part of the
> > > > > > > > linker
> > > > > > > > line from pkg-config. At this point I'll just break the
> > > > > > > > Go
> > > > > > > > application up into a separate C application that
> > > > > > > > handles all
> > > > > > > > the DPDK parts, and send messages between them.
> > > > > > > 
> > > > > > > Hi,
> > > > > > > 
> > > > > > > As far as I can see, both mnl and mlx5 (and all the other
> > > > > > > reverse
> > > > > > > dependencies) are listed correctly in the libdpdk.pc
> > > > > > > Libs.private entry, and pkg-config --libs --static
> > > > > > > libdpdk.pc
> > > > > > > does print them as intended. This is with 18.11-rc3.
> > > > > > > Are you sure everything is correct (pkg-config path is
> > > > > > > right, --
> > > > > > > static is used, etc)?
> > > > > > > 
> > > > > > > --
> > > > > > > Kind regards,
> > > > > > > Luca Boccassi
> > > > > > 
> > > > > > Hi Luca, here is what pkg-config gives:
> > > > > > 
> > > > > > PKG_CONFIG_PATH=meson-private/ pkg-config --libs --static
> > > > > > libdpdk
> > > > > > -L/usr/local/lib/x86_64-linux-gnu -lrte_eventdev
> > > > > > -lrte_power
> > > > > > -lrte_ip_frag -lrte_hash -lrte_pdump -lrte_eal
> > > > > > -lrte_pipeline
> > > > > > -lrte_table -lrte_bbdev -lrte_bpf -lrte_vhost -lrte_metrics
> > > > > > -lrte_jobstats -lrte_net -lrte_reorder -lrte_ring
> > > > > > -lrte_mempool
> > > > > > -lrte_security -lrte_compressdev -lrte_rawdev -lrte_mbuf
> > > > > > -lrte_kvargs -lrte_port -lrte_pci -lrte_ethdev -lrte_gro
> > > > > > -lrte_gso
> > > > > > -lrte_cryptodev -lrte_sched -lrte_latencystats -lrte_efd
> > > > > > -lrte_distributor -lrte_meter -lrte_acl -lrte_member
> > > > > > -lrte_cmdline
> > > > > > -lrte_lpm -lrte_kni -lrte_cfgfile -lrte_bitratestats
> > > > > > -lrte_timer
> > > > > > -lrte_flow_classify -lrte_mempool_bucket
> > > > > > -lrte_pmd_null_crypto
> > > > > > -lrte_pmd_failsafe -lrte_bus_ifpga -lrte_pmd_atlantic
> > > > > > -lrte_pmd_mlx4 -lrte_pmd_vmxnet3 -lrte_pmd_avp
> > > > > > -lrte_common_dpaax
> > > > > > -lrte_pmd_ena -lcrypto -lrte_bus_fslmc -ldl -lrte_pmd_avf
> > > > > > -lrte_pmd_crypto_scheduler -lrte_pmd_netvsc -lrte_pmd_vhost
> > > > > > -lrte_bus_dpaa -lrte_mempool_dpaa2 -lrte_common_octeontx
> > > > > > -lrte_pmd_liquidio -lrte_pmd_ifc -Wl,-Bdynamic -lnuma
> > > > > > -lrte_pmd_enic -lrte_common_cpt -pthread
> > > > > > -lrte_pmd_octeontx_crypto
> > > > > > -lrte_pmd_qat -lrte_bus_vmbus -lrte_pmd_null -lm
> > > > > > -lrte_pmd_dpaa
> > > > > > -lrte_bus_vdev -lrte_pmd_dpaa2 -lrte_pmd_skeleton_event
> > > > > > -lrte_pmd_af_packet -lrte_pmd_octeontx -lrte_pmd_thunderx
> > > > > > -lrte_pmd_ring -lrte_pmd_octeontx_event -lrte_pmd_sw_event
> > > > > > -lrte_pmd_ark -lrte_mempool_octeontx -lrte_pmd_ixgbe
> > > > > > -lrte_pmd_kni
> > > > > > -lrte_mempool_ring -lrte_pmd_virtio_crypto
> > > > > > -lrte_mempool_dpaa
> > > > > > -lrte_pmd_dpaa2_cmdif -lrte_bus_pci -lrte_pmd_opdl_event
> > > > > > -lrte_pmd_mlx5 -lrte_pmd_virtio -lrte_pmd_tap
> > > > > > -lrte_pmd_caam_jr
> > > > > > -lrte_pmd_dpaa2_sec -lrte_pmd_dpaa2_qdma -lrte_pmd_enetc
> > > > > > -lrte_pmd_sfc -lrte_pmd_bnxt -lrte_pmd_dpaa2_event
> > > > > > -lrte_pmd_cxgbe
> > > > > > -Wl,--whole-archive -Wl,--no- as-needed -lrte_pmd_e1000
> > > > > > -lrte_pmd_softnic -lrte_pmd_bond -lrte_pmd_fm10k
> > > > > > -lrte_pmd_i40e
> > > > > > -lrte_pmd_nfp -lrte_pmd_qede -Wl,--no- whole-archive
> > > > > > -lrte_pmd_axgbe -lrte_pmd_ccp -lrte_pmd_ifpga_rawdev
> > > > > > -lrte_pmd_bbdev_null -lrte_pmd_openssl -lrte_pmd_dsw_event
> > > > > > -lrte_pmd_dpaa_event -lrte_mempool_stack
> > > > > > -lrte_pmd_vdev_netvsc
> > > > > > -lrte_pmd_dpaa_sec -lrte_pmd_skeleton_rawdev
> > > > > > -lrte_pmd_octeontx_compress
> > > > > > 
> > > > > > You'll notice there's no mlx5 or mnl in that list. I was
> > > > > > using
> > > > > > 18.11-
> > > > > > rc2 since I cloned early yesterday. Perhaps meson
> > > > > > determined not
> > > > > > to put it in there for some reason?
> > > > > 
> > > > > Were mlx5/mnl found at meson configure time?
> > > > > 
> > > > > --
> > > > > Kind regards,
> > > > > Luca Boccassi
> > > > 
> > > > Hi Luca, yes, it was:
> > > > 
> > > > Library mnl found: YES
> > > > Library mlx4 found: YES
> > > > Library ibverbs found: YES
> > > > Compiler for C supports argument -Wextra: YES Compiler for C
> > > > supports
> > > > argument -std=c11: YES Compiler for C supports argument
> > > > -Wno-strict-prototypes: YES Compiler for C supports argument
> > > > -D_BSD_SOURCE: YES Compiler for C supports argument
> > > > -D_DEFAULT_SOURCE:
> > > > YES Compiler for C supports argument -D_XOPEN_SOURCE=600: YES
> > > > Checking
> > > > whether type "struct mlx4_wqe_lso_seg" has member
> > > > "mss_hdr_size": YES
> > > > Configuring mlx4_autoconf.h using configuration Library mnl
> > > > found: YES
> > > > Library mlx5 found: YES Library ibverbs found: YES ...
> > > > PKG_CONFIG_PATH=meson-private/ pkg-config --libs --static
> > > > libdpdk
> > > > -L/usr/local/lib/x86_64-linux-gnu -lrte_eventdev -lrte_power
> > > > -lrte_ip_frag -lrte_hash -lrte_pdump -lrte_eal -lrte_pipeline
> > > > -lrte_table -lrte_bbdev -lrte_bpf -lrte_vhost -lrte_metrics
> > > > -lrte_jobstats -lrte_net -lrte_reorder -lrte_ring -lrte_mempool
> > > > -lrte_security -lrte_compressdev -lrte_rawdev -lrte_mbuf
> > > > -lrte_kvargs
> > > > -lrte_port -lrte_pci -lrte_ethdev -lrte_gro -lrte_gso
> > > > -lrte_cryptodev
> > > > -lrte_sched -lrte_latencystats -lrte_efd -lrte_distributor
> > > > -lrte_meter
> > > > -lrte_acl -lrte_member -lrte_cmdline -lrte_lpm -lrte_kni
> > > > -lrte_cfgfile
> > > > -lrte_bitratestats -lrte_timer -lrte_flow_classify
> > > > -lrte_pmd_ccp
> > > > -lrte_mempool_bucket -lrte_pmd_failsafe -lrte_pmd_netvsc
> > > > -lrte_pmd_null_crypto -lrte_bus_ifpga -lrte_pmd_atlantic
> > > > -lrte_pmd_octeontx_event -lrte_pmd_avp -lrte_pmd_mlx4
> > > > -lrte_common_dpaax -lrte_pmd_skeleton_rawdev -lrte_pmd_ena
> > > > -lrte_pmd_opdl_event -lrte_bus_fslmc -lnuma -lrte_pmd_avf
> > > > -lrte_pmd_crypto_scheduler -lrte_pmd_vhost -lrte_bus_dpaa
> > > > -lrte_mempool_dpaa2 -lrte_common_octeontx -Wl,--no-as-needed
> > > > -lcrypto
> > > > -lrte_pmd_ifc -lrte_pmd_liquidio -lrte_pmd_enic
> > > > -lrte_common_cpt
> > > > -Wl,--no-whole-archive -lrte_bus_vmbus
> > > > -lrte_pmd_octeontx_crypto
> > > > -lrte_pmd_qat -lrte_pmd_ifpga_rawdev -lrte_pmd_dpaa
> > > > -lrte_bus_vdev
> > > > -lrte_pmd_bbdev_null -lrte_pmd_dpaa2 -lrte_pmd_skeleton_event
> > > > -lrte_pmd_ring -lrte_pmd_af_packet -lrte_pmd_thunderx
> > > > -lrte_pmd_dpaa_event -lrte_pmd_octeontx_compress
> > > > -lrte_pmd_dpaa_sec
> > > > -lrte_pmd_sw_event -Wl,--whole-archive -lrte_pmd_ark
> > > > -lrte_mempool_octeontx -lrte_pmd_ixgbe -lrte_mempool_ring
> > > > -lrte_pmd_kni -lrte_pmd_vmxnet3 -lrte_mempool_dpaa
> > > > -lrte_bus_pci
> > > > -lrte_pmd_dpaa2_cmdif -lrte_pmd_mlx5 -lrte_pmd_tap
> > > > -lrte_pmd_caam_jr
> > > > -lrte_pmd_dpaa2_sec -lm -lrte_pmd_dpaa2_qdma -lrte_pmd_enetc
> > > > -lrte_pmd_virtio -lrte_pmd_bnxt -lrte_pmd_dpaa2_event
> > > > -lrte_pmd_sfc
> > > > -lrte_pmd_cxgbe -pthread -lrte_pmd_e1000 -lrte_pmd_softnic -ldl
> > > > -lrte_pmd_null -lrte_pmd_bond -lrte_pmd_fm10k -lrte_pmd_i40e
> > > > -lrte_pmd_nfp -lrte_pmd_qede -lrte_pmd_axgbe -Wl,-Bdynamic
> > > > -lrte_pmd_openssl -lrte_pmd_octeontx -lrte_pmd_dsw_event
> > > > -lrte_mempool_stack -lrte_pmd_virtio_crypto
> > > > -lrte_pmd_vdev_netvsc
> > > 
> > > Is this with latest DPDK from git? because I see the exact same
> > > as Luca:
> > > 
> > > $ PKG_CONFIG_PATH=build/meson-private/ pkg-config --libs --static
> > 
> > libdpdk | grep mlx
> > > -L/usr/local/lib64 -lrte_telemetry -lrte_bpf -lrte_flow_classify
> > > -
> > 
> > lrte_pipeline -lrte_table -lrte_port -lrte_vhost -lrte_security -
> > lrte_sched -lrte_reorder -lrte_rawdev -lrte_pdump -lrte_power
> > -lrte_meter
> > -lrte_member -lrte_lpm -lrte_latencystats -lrte_kni -lrte_jobstats
> > -
> > lrte_ip_frag -lrte_gso -lrte_gro -lrte_eventdev -lrte_efd -
> > lrte_distributor -lrte_cryptodev -lrte_compressdev -lrte_cfgfile -
> > lrte_bitratestats -lrte_bbdev -lrte_acl -lrte_timer -lrte_hash -
> > lrte_metrics -lrte_pci -lrte_ethdev -lrte_net -lrte_mbuf
> > -lrte_mempool -
> > lrte_ring -lrte_eal -lrte_kvargs -lrte_cmdline -L/usr/local/lib64 -
> > lrte_kvargs -lrte_eal -lrte_ring -lrte_mempool -lrte_mbuf -lrte_pci
> > -
> > lrte_cryptodev -lrte_net -lrte_cmdline -lrte_ethdev -lrte_hash
> > -lrte_timer
> > -lrte_common_dpaax -lrte_eventdev -lrte_rawdev -lrte_bus_dpaa -
> > lrte_bus_fslmc -lrte_bus_pci -lrte_common_octeontx -lrte_bus_vdev -
> > lrte_meter -lrte_sched -lrte_ip_frag -lz -lrte_mempool_dpaa -
> > lrte_mempool_dpaa2 -lrte_vhost -lrte_security -lrte_kni -lmnl
> > -lmlx4 -
> > libverbs -lmnl -lmlx5 -libverbs -lrte_bus_vmbus
> > -lrte_mempool_octeontx -
> > lpcap -lrte_port -lrte_lpm -lrte_acl -lrte_table -lrte_pipeline
> > -lsze2 -
> > lrte_gso -lIPSec_MB -lIPSec_MB -lrte_common_cpt -lrte_reorder -
> > lrte_compressdev -lrte_pmd_dpaa -lrte_pmd_dpaa2 -lrte_pmd_dpaa2_sec
> > -
> > lrte_pmd_octeontx -lrte_bbdev -lrte_bus_ifpga -Wl,--whole-archive -
> > lrte_mempool_bucket -lrte_mempool_ring -lrte_mempool_stack -
> > lrte_pmd_af_packet -lrte_pmd_ark -lrte_pmd_atlantic -lrte_pmd_avf -
> > lrte_pmd_avp -lrte_pmd_axgbe -lrte_pmd_bond -lrte_pmd_bnx2x
> > -lrte_pmd_bnxt
> > -lrte_pmd_cxgbe -lrte_pmd_e1000 -lrte_pmd_ena -lrte_pmd_enetc -
> > lrte_pmd_enic -lrte_pmd_failsafe -lrte_pmd_fm10k -lrte_pmd_i40e -
> > lrte_pmd_ifc -lrte_pmd_ixgbe -lrte_pmd_kmod -lrte_pmd_kni -
> > lrte_pmd_liquidio -lrte_pmd_mlx4 -lrte_pmd_mlx5 -lrte_pmd_netvsc -
> > lrte_pmd_nfp -lrte_pmd_null -lrte_pmd_pcap -lrte_pmd_qede
> > -lrte_pmd_ring -
> > lrte_pmd_sfc -lrte_pmd_softnic -lrte_pmd_szedata2 -lrte_pmd_tap -
> > lrte_pmd_thunderx -lrte_pmd_vdev_netvsc -lrte_pmd_vhost
> > -lrte_pmd_virtio -
> > lrte_pmd_vmxnet3 -lrte_pmd_aesni_gcm -lrte_pmd_aesni_mb
> > -lrte_pmd_caam_jr
> > -lrte_pmd_ccp -lrte_pmd_dpaa_sec -lrte_pmd_null_crypto -
> > lrte_pmd_octeontx_crypto -lrte_pmd_openssl
> > -lrte_pmd_crypto_scheduler -
> > lrte_pmd_virtio_crypto -lrte_pmd_octeontx_compress -lrte_pmd_qat -
> > lrte_pmd_zlib -lrte_pmd_dpaa_event -lrte_pmd_dpaa2_event -
> > lrte_pmd_octeontx_event -lrte_pmd_opdl_event
> > -lrte_pmd_skeleton_event -
> > lrte_pmd_sw_event -lrte_pmd_dsw_event -lrte_pmd_bbdev_null -
> > lrte_pmd_skeleton_rawdev -lrte_pmd_dpaa2_cmdif -lrte_pmd_dpaa2_qdma
> > -
> > lrte_pmd_ifpga_rawdev -lrte_pmd_ioat_copy -Wl,--no-whole-archive
> > -Wl,-
> > Bdynamic -Wl,--no-as-needed -pthread -lm -ldl -lnuma -lbsd -lpcap
> > -lcrypto
> > -lcrypto -lz -lcrypto -ldl -pthread -lz
> > 
> > Hi Bruce, I tried with rc3 and a new clone from right now, and get
> > the
> > same results:
> > 
> > $ meson build
> > The Meson build system
> > Version: 0.45.1
> > Source dir: /home/cburdick/dpdk
> > Build dir: /home/cburdick/dpdk/build
> > Build type: native build
> > Project name: DPDK
> > Native C compiler: cc (gcc 7.3.0 "cc (Ubuntu 7.3.0-27ubuntu1~18.04)
> > 7.3.0")
> > Build machine cpu family: x86_64
> > Build machine cpu: x86_64
> > Library numa found: YES
> > Has header "numaif.h": YES
> > Library bsd found: NO
> > Checking for size of "void *": 8
> > Compiler for C supports argument -Wsign-compare: YES
> > Compiler for C supports argument -Wcast-qual: YES
> > Compiler for C supports argument -Wno-address-of-packed-member: YES
> > Fetching value of define "__SSE4_2__": 1
> > Fetching value of define "__AES__": 1
> > Fetching value of define "__PCLMUL__": 1
> > Fetching value of define "__AVX__": 1
> > Fetching value of define "__AVX2__": 1
> > Fetching value of define "__AVX512F__":
> > Compiler for C supports argument -Wno-format-truncation: YES
> > Checking for size of "void *": 8
> > Has header "linux/userfaultfd.h": YES
> > Checking for size of "void *": 8
> > Library elf found: NO
> > Library jansson found: NO
> > Program gen-pmdinfo-cfile.sh found: YES
> > (/home/cburdick/dpdk/buildtools/gen-pmdinfo-cfile.sh)
> > Compiler for C supports argument -Wno-format-truncation: YES
> > Library libmusdk found: NO
> > Compiler for C supports argument -Wno-cast-qual: YES
> > Compiler for C supports argument -Wno-pointer-to-int-cast: YES
> > Library z found: NO
> > Compiler for C supports argument -Wno-uninitialized: YES
> > Compiler for C supports argument -Wno-unused-parameter: YES
> > Compiler for C supports argument -Wno-unused-variable: YES
> > Compiler for C supports argument -Wno-misleading-indentation: YES
> > Compiler for C supports argument -Wno-implicit-fallthrough: YES
> > Checking for size of "void *": 8
> > Compiler for C supports argument -Wno-unused-parameter: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wno-format-extra-args: YES
> > Compiler for C supports argument -Wno-unused-variable: YES
> > Compiler for C supports argument -Wno-missing-field-initializers:
> > YES
> > Compiler for C supports argument -Wno-sign-compare: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-format: YES
> > Compiler for C supports argument -Wno-error=format-security: YES
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wno-unused-but-set-variable: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-unused-but-set-variable: YES
> > Library mnl found: YES
> > Library mlx4 found: YES
> > Library ibverbs found: YES
> > Compiler for C supports argument -Wextra: YES
> > Compiler for C supports argument -std=c11: YES
> > Compiler for C supports argument -Wno-strict-prototypes: YES
> > Compiler for C supports argument -D_BSD_SOURCE: YES
> > Compiler for C supports argument -D_DEFAULT_SOURCE: YES
> > Compiler for C supports argument -D_XOPEN_SOURCE=600: YES
> > Checking whether type "struct mlx4_wqe_lso_seg" has member
> > "mss_hdr_size":
> > YES
> > Configuring mlx4_autoconf.h using configuration
> > Library mnl found: YES
> > Library mlx5 found: YES
> > Library ibverbs found: YES
> > Compiler for C supports argument -Wextra: YES
> > Compiler for C supports argument -std=c11: YES
> > Compiler for C supports argument -Wno-strict-prototypes: YES
> > Compiler for C supports argument -D_BSD_SOURCE: YES
> > Compiler for C supports argument -D_DEFAULT_SOURCE: YES
> > Compiler for C supports argument -D_XOPEN_SOURCE=600: YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "MLX5DV_CQE_RES_FORMAT_CSUM_STRIDX": YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "MLX5DV_CONTEXT_MASK_TUNNEL_OFFLOADS": YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "MLX5DV_CONTEXT_FLAGS_MPW_ALLOWED": YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "MLX5DV_CONTEXT_FLAGS_CQE_128B_COMP": YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "MLX5DV_CQ_INIT_ATTR_FLAGS_CQE_PAD": YES
> > Header <infiniband/mlx5dv.h> has symbol
> > "mlx5dv_create_flow_action_packet_reformat": NO
> > Header <infiniband/verbs.h> has symbol "IBV_FLOW_SPEC_MPLS": YES
> > Header <infiniband/verbs.h> has symbol
> > "IBV_WQ_FLAG_RX_END_PADDING": NO
> > Header <linux/ethtool.h> has symbol "SUPPORTED_40000baseKR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_40000baseCR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_40000baseSR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_40000baseLR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_56000baseKR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_56000baseCR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_56000baseSR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol "SUPPORTED_56000baseLR4_Full":
> > YES
> > Header <linux/ethtool.h> has symbol
> > "ETHTOOL_LINK_MODE_25000baseCR_Full_BIT": YES
> > Header <linux/ethtool.h> has symbol
> > "ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT": YES
> > Header <linux/ethtool.h> has symbol
> > "ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT": YES
> > Header <linux/if_link.h> has symbol "IFLA_PHYS_SWITCH_ID": YES
> > Header <linux/if_link.h> has symbol "IFLA_PHYS_PORT_NAME": YES
> > Header <linux/if_link.h> has symbol "IFLA_VXLAN_COLLECT_METADATA":
> > YES
> > Header <linux/rtnetlink.h> has symbol "TCA_CHAIN": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_ACT": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_FLAGS": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ETH_TYPE": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ETH_DST": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ETH_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ETH_SRC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ETH_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IP_PROTO": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV4_SRC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV4_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV4_DST": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV4_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV6_SRC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV6_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV6_DST": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_IPV6_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_TCP_SRC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_TCP_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_TCP_DST": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_TCP_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_UDP_SRC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_UDP_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_UDP_DST": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_UDP_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_VLAN_ID": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_VLAN_PRIO": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_VLAN_ETH_TYPE":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_TCP_FLAGS": YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_TCP_FLAGS_MASK": YES
> > Header <linux/pkt_cls.h> has symbol "TC_ACT_GOTO_CHAIN": YES
> > Header <linux/tc_act/tc_vlan.h> has symbol
> > "TCA_VLAN_PUSH_VLAN_PRIORITY":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ENC_KEY_ID":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ENC_IPV4_SRC":
> > YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_IPV4_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ENC_IPV4_DST":
> > YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_IPV4_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ENC_IPV6_SRC":
> > YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_IPV6_SRC_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_ENC_IPV6_DST":
> > YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_IPV6_DST_MASK":
> > YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_UDP_SRC_PORT": YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_UDP_SRC_PORT_MASK": YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_UDP_DST_PORT": YES
> > Header <linux/pkt_cls.h> has symbol
> > "TCA_FLOWER_KEY_ENC_UDP_DST_PORT_MASK": YES
> > Header <linux/tc_act/tc_tunnel_key.h> has symbol
> > "TCA_ACT_TUNNEL_KEY": YES
> > Header <linux/tc_act/tc_tunnel_key.h> has symbol
> > "TCA_TUNNEL_KEY_ENC_DST_PORT": YES
> > Header <linux/tc_act/tc_tunnel_key.h> has symbol
> > "TCA_TUNNEL_KEY_NO_CSUM":
> > YES
> > Header <linux/tc_act/tc_pedit.h> has symbol
> > "TCA_PEDIT_KEY_EX_HDR_TYPE_UDP": YES
> > Header <rdma/rdma_netlink.h> has symbol "RDMA_NL_NLDEV": YES
> > Header <rdma/rdma_netlink.h> has symbol "RDMA_NLDEV_CMD_GET": YES
> > Header <rdma/rdma_netlink.h> has symbol "RDMA_NLDEV_CMD_PORT_GET":
> > YES
> > Header <rdma/rdma_netlink.h> has symbol
> > "RDMA_NLDEV_ATTR_DEV_INDEX": YES
> > Header <rdma/rdma_netlink.h> has symbol "RDMA_NLDEV_ATTR_DEV_NAME":
> > YES
> > Header <rdma/rdma_netlink.h> has symbol
> > "RDMA_NLDEV_ATTR_PORT_INDEX": YES
> > Header <rdma/rdma_netlink.h> has symbol
> > "RDMA_NLDEV_ATTR_NDEV_INDEX": NO
> > Checking whether type "struct mlx5dv_sw_parsing_caps" has member
> > "sw_parsing_offloads": YES
> > Checking whether type "struct ibv_counter_set_init_attr" has member
> > "counter_set_id": YES
> > Checking whether type "struct ibv_counters_init_attr" has member
> > "comp_mask": NO
> > Configuring mlx5_autoconf.h using configuration
> > Library libmusdk found: NO
> > Library libmusdk found: NO
> > Library pcap found: NO
> > Compiler for C supports argument -Wno-unused-parameter: YES
> > Compiler for C supports argument -Wno-sign-compare: YES
> > Compiler for C supports argument -Wno-missing-prototypes: YES
> > Compiler for C supports argument -Wno-cast-qual: YES
> > Compiler for C supports argument -Wno-unused-function: YES
> > Compiler for C supports argument -Wno-unused-variable: YES
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wno-missing-prototypes: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-format-nonliteral: YES
> > Compiler for C supports argument -Wno-shift-negative-value: YES
> > Compiler for C supports argument -Wno-unused-but-set-variable: YES
> > Compiler for C supports argument -Wno-missing-declarations: YES
> > Compiler for C supports argument -Wno-maybe-uninitialized: YES
> > Compiler for C supports argument -Wno-strict-prototypes: YES
> > Compiler for C supports argument -Wno-shift-negative-value: YES
> > Compiler for C supports argument -Wno-implicit-fallthrough: YES
> > Compiler for C supports argument -Wno-format-extra-args: YES
> > Compiler for C supports argument -Wno-visibility: YES
> > Compiler for C supports argument -Wno-empty-body: YES
> > Compiler for C supports argument -Wno-invalid-source-encoding: YES
> > Compiler for C supports argument -Wno-sometimes-uninitialized: YES
> > Compiler for C supports argument -Wno-pointer-bool-conversion: YES
> > Checking for size of "void *": 8
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wextra: YES
> > Compiler for C supports argument -Wdisabled-optimization: YES
> > Compiler for C supports argument -Waggregate-return: YES
> > Compiler for C supports argument -Wnested-externs: YES
> > Compiler for C supports argument -Wbad-function-cast: YES
> > Compiler for C supports argument -Wno-sign-compare: YES
> > Compiler for C supports argument -Wno-unused-parameter: YES
> > Compiler for C supports argument -Wno-unused-variable: YES
> > Compiler for C supports argument -Wno-empty-body: YES
> > Compiler for C supports argument -Wno-unused-but-set-variable: YES
> > Library sze2 found: NO
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_UNSPEC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_FLOWER_KEY_VLAN_PRIO": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_BPF_UNSPEC": YES
> > Header <linux/pkt_cls.h> has symbol "TCA_BPF_FD": YES
> > Header <linux/tc_act/tc_bpf.h> has symbol "TCA_ACT_BPF_UNSPEC": YES
> > Header <linux/tc_act/tc_bpf.h> has symbol "TCA_ACT_BPF_FD": YES
> > Configuring tap_autoconf.h using configuration
> > Compiler for C supports argument -fno-prefetch-loop-arrays: YES
> > Compiler for C supports argument -Wno-maybe-uninitialized: YES
> > Compiler for C supports argument -Wall: YES
> > Compiler for C supports argument -Wextra: YES
> > Compiler for C supports argument -D_BSD_SOURCE: YES
> > Compiler for C supports argument -D_DEFAULT_SOURCE: YES
> > Compiler for C supports argument -D_XOPEN_SOURCE=600: YES
> > Compiler for C supports argument -Wno-unused-parameter: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wno-format-extra-args: YES
> > Library IPSec_MB found: NO
> > Library IPSec_MB found: NO
> > Found pkg-config: /usr/bin/pkg-config (0.29.1)
> > Native dependency libcrypto found: YES 1.1.0g
> > Library libsso_kasumi found: NO
> > Library libmusdk found: NO
> > Dependency libcrypto found: YES (cached)
> > Dependency libcrypto found: YES (cached)
> > Library libsso_zuc found: NO
> > Dependency libisal found: NO
> > Dependency zlib found: NO
> > Compiler for C supports argument -Wno-sign-compare: YES
> > Compiler for C supports argument -Wno-unused-value: YES
> > Compiler for C supports argument -Wno-format: YES
> > Compiler for C supports argument -Wno-error=format-security: YES
> > Compiler for C supports argument -Wno-strict-aliasing: YES
> > Compiler for C supports argument -Wno-unused-but-set-variable: YES
> > Library execinfo found: NO
> > Compiler for C supports argument -Wno-format-truncation: YES
> > Dependency zlib found: NO
> > Library execinfo found: NO
> > Program doxygen found: NO
> > Program sphinx-build found: NO
> > kernel/linux/kni/meson.build:16: WARNING: Passed invalid keyword
> > argument
> > "console".
> > WARNING: This will become a hard error in the future.
> > WARNING: Unknown keyword arguments in target rte_kni: console
> > Configuring rte_build_config.h using configuration
> > Program buildtools/symlink-drivers-solibs.sh found: YES (/bin/sh
> > /home/cburdick/dpdk/buildtools/symlink-drivers-solibs.sh)
> > Message:
> > =================
> > Libraries Enabled
> > =================
> > 
> > libs:
> > \tcompat, cmdline, kvargs, eal, ring, mempool, mbuf, net,
> > \tethdev, pci, metrics, hash, timer, acl, bbdev, bitratestats,
> > \tcfgfile, compressdev, cryptodev, distributor, efd, eventdev, gro,
> > gso,
> > \tip_frag, jobstats, kni, latencystats, lpm, member, meter, power,
> > \tpdump, rawdev, reorder, sched, security, vhost, port, table,
> > \tpipeline, flow_classify, bpf,
> > 
> > Build targets in project: 411
> > Found ninja-1.8.2 at /usr/bin/ninja
> > [cburdick at dev01 ~/dpdk] (master)
> > $ cd build
> > [cburdick at dev01 ~/dpdk/build] (master)
> > $ ninja
> > [1428/1431] Generating igb_uio with a custom command.
> > make: Entering directory '/usr/src/linux-headers-4.15.0-20-generic'
> > Makefile:976: "Cannot use CONFIG_STACK_VALIDATION=y, please install
> > libelf-dev, libelf-devel or elfutils-libelf-devel"
> >   CC [M]  /home/cburdick/dpdk/build/kernel/linux/igb_uio/igb_uio.o
> >   Building modules, stage 2.
> >   MODPOST 1 modules
> >  
> > CC      /home/cburdick/dpdk/build/kernel/linux/igb_uio/igb_uio.mod.
> > o
> >   LD [M]  /home/cburdick/dpdk/build/kernel/linux/igb_uio/igb_uio.ko
> > make: Leaving directory '/usr/src/linux-headers-4.15.0-20-generic'
> > [1431/1431] Generating rte_kni with a custom command.
> > make: Entering directory '/usr/src/linux-headers-4.15.0-20-generic'
> > Makefile:976: "Cannot use CONFIG_STACK_VALIDATION=y, please install
> > libelf-dev, libelf-devel or elfutils-libelf-devel"
> >   CC [M]  /home/cburdick/dpdk/build/kernel/linux/kni/kni_net.o
> >   CC [M]  /home/cburdick/dpdk/build/kernel/linux/kni/kni_misc.o
> >   CC [M]  /home/cburdick/dpdk/build/kernel/linux/kni/kni_ethtool.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_etht
> > ool.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_8259
> > 9.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_api.
> > o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_x540
> > .o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_comm
> > on.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_phy.
> > o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_8259
> > 8.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/ixgbe_main
> > .o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/ixgbe/kcompat.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_82575.
> > o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_i210.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_mbx.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_api.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/igb_main.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/igb_vmdq.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_manage
> > .o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/igb_ethtool.
> > o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/igb_param.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_mac.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_phy.o
> >   CC [M]
> > /home/cburdick/dpdk/build/kernel/linux/kni/ethtool/igb/e1000_nvm.o
> >   LD [M]  /home/cburdick/dpdk/build/kernel/linux/kni/rte_kni.o
> >   Building modules, stage 2.
> >   MODPOST 1 modules
> >   CC      /home/cburdick/dpdk/build/kernel/linux/kni/rte_kni.mod.o
> >   LD [M]  /home/cburdick/dpdk/build/kernel/linux/kni/rte_kni.ko
> > make: Leaving directory '/usr/src/linux-headers-4.15.0-20-generic'
> > [cburdick at dev01 ~/dpdk/build] (master)
> > $ PKG_CONFIG_PATH=meson-private/ pkg-config --libs --static
> > libdpdk|grep
> > mlx
> > -L/usr/local/lib/x86_64-linux-gnu -lrte_flow_classify
> > -lrte_eventdev -
> > lrte_ip_frag -lrte_power -lrte_hash -lrte_pdump -lrte_pipeline
> > -lrte_table
> > -lrte_mbuf -lrte_bbdev -lrte_bpf -lrte_vhost -lrte_metrics
> > -lrte_mempool -
> > lrte_jobstats -lrte_reorder -lrte_net -lrte_security -lrte_eal
> > -lrte_ring
> > -lrte_ethdev -lrte_compressdev -lrte_rawdev -lrte_kvargs -lrte_pci
> > -
> > lrte_cfgfile -lrte_gro -lrte_gso -lrte_cryptodev -lrte_latencystats
> > -
> > lrte_sched -lrte_efd -lrte_distributor -lrte_acl -lrte_member -
> > lrte_cmdline -lrte_lpm -lrte_meter -lrte_kni -lrte_bitratestats -
> > lrte_timer -lrte_port -lrte_mempool_bucket -lrte_pmd_vdev_netvsc -
> > lrte_pmd_ark -lrte_pmd_failsafe -lrte_pmd_netvsc
> > -lrte_pmd_null_crypto -
> > lrte_bus_ifpga -lrte_common_dpaax -lrte_pmd_ixgbe
> > -lrte_mempool_ring -
> > lrte_pmd_kni -lrte_pmd_vmxnet3 -lrte_pmd_mlx4 -lrte_pmd_virtio
> > -Wl,--no-
> > as-needed -lrte_mempool_dpaa -lrte_pmd_ena -lrte_bus_fslmc
> > -lrte_pmd_avf -
> > lrte_pmd_dpaa2_sec -lrte_common_octeontx -lrte_pmd_skeleton_rawdev
> > -
> > lrte_pmd_crypto_scheduler -lrte_pmd_dpaa2_qdma -lrte_pmd_vhost -ldl
> > -
> > lrte_bus_dpaa -lrte_pmd_fm10k -lrte_pmd_bnxt -lrte_pmd_qat
> > -lrte_pmd_bond
> > -lrte_pmd_axgbe -lrte_pmd_dpaa2 -lrte_pmd_skeleton_event -
> > lrte_pmd_dpaa_event -lrte_mempool_stack -pthread -lrte_pmd_ccp -
> > lrte_pmd_octeontx_compress -lrte_pmd_sw_event
> > -lrte_mempool_octeontx -Wl,-
> > Bdynamic -lrte_pmd_dpaa_sec -lrte_pmd_atlantic
> > -lrte_pmd_octeontx_event -
> > lrte_pmd_avp -lrte_bus_pci -lrte_pmd_dpaa2_cmdif -lrte_pmd_mlx5 -
> > lrte_pmd_opdl_event -lrte_pmd_tap -lrte_pmd_caam_jr -lrte_pmd_sfc
> > -lcrypto
> > -lrte_pmd_enetc -lrte_mempool_dpaa2 -lrte_pmd_dpaa2_event
> > -lrte_pmd_ifc -
> > lrte_pmd_liquidio -lrte_pmd_cxgbe -lm -lrte_pmd_enic -lrte_bus_vdev
> > -
> > lrte_pmd_e1000 -lrte_pmd_softnic -lrte_pmd_ifpga_rawdev
> > -lrte_bus_vmbus -
> > lrte_pmd_octeontx_crypto -lrte_pmd_null -lnuma -lrte_common_cpt -
> > lrte_pmd_nfp -lrte_pmd_qede -lrte_pmd_i40e -lrte_pmd_dpaa -Wl,
> > --whole-
> > archive -lrte_pmd_bbdev_null -lrte_pmd_af_packet -lrte_pmd_thunderx
> > -
> > lrte_pmd_openssl -lrte_pmd_octeontx -lrte_pmd_dsw_event -Wl,--no-
> > whole-
> > archive -lrte_pmd_ring -lrte_pmd_virtio_crypto
> 
> That is strange. Can you try one last thing - can you update meson
> with "pip3 install --upgrade meson" and see if that makes any
> difference? [If you are using your distro's meson from /usr/bin right
> now, you'll probably also need to run "hash meson" afterwards too].
> Perhaps we have a hidden dependency on later meson versions or
> something like that.
> 
> /Bruce

We do - I can reproduce the same issue with 0.45.1, while normally I
run 0.47.2. Should we bump the minimum version? Or simply document it?

-- 
Kind regards,
Luca Boccassi


More information about the dev mailing list