[dpdk-dev] mlx5 FDIR rule comparison issue

Dekel Peled dekelp at mellanox.com
Thu Apr 4 13:18:00 CEST 2019


Hi Daniel,

The flow_director API will be deprecated in the near future.
It was replaced by rte_flow API, which contains much more features, and is fully supported by Mellanox.

It is recommended that you use rte_flow API in your application.

Regards,
Dekel

> -----Original Message-----
> From: benli ye <danielbenliye at gmail.com>
> Sent: Wednesday, April 3, 2019 11:30 AM
> To: Dekel Peled <dekelp at mellanox.com>
> Cc: dev at dpdk.org
> Subject: Re: mlx5 FDIR rule comparison issue
> 
> +Dekel
> 
> Add Dekel to see if this is an issue.
> 
> Thanks,
> Daniel
> 
> > On Apr 2, 2019, at 3:23 PM, benli ye <danielbenliye at gmail.com> wrote:
> >
> > Hi Developers,
> >
> > I am adding two FDIR rule (one is for UDP and the other is for TCP) for mlx5
> pmd driver. The rules are listed below.
> >    struct rte_eth_fdir_filter filt[MAX_FDIR_PROTO] = {
> >        {
> >            .input.flow_type = RTE_ETH_FLOW_NONFRAG_IPV4_TCP,
> >            .input.flow.tcp4_flow.ip.dst_ip = dip,
> >            .input.flow.tcp4_flow.dst_port = dport,
> >
> >            .action.behavior = RTE_ETH_FDIR_ACCEPT,
> >            .action.report_status = RTE_ETH_FDIR_REPORT_ID,
> >            .soft_id = 0,
> >        },
> >        {
> >            .input.flow_type = RTE_ETH_FLOW_NONFRAG_IPV4_UDP,
> >            .input.flow.udp4_flow.ip.dst_ip = dip,
> >            .input.flow.udp4_flow.dst_port = dport,
> >
> >            .action.behavior = RTE_ETH_FDIR_ACCEPT,
> >            .action.report_status = RTE_ETH_FDIR_REPORT_ID,
> >            .soft_id = 1,
> >        },
> >    };
> >
> > However, mlx5 lib prevent me to doing this as when it treats the two rules
> are the same.
> >
> > I debugged for a while and found flow_fdir_cmp() didn’t compare the
> protocol type in field items of struct mlx5_fdir. So should this be a bug for
> mlx5?
> >
> > flow_fdir_cmp(const struct mlx5_fdir *f1, const struct mlx5_fdir *f2)
> > {
> > 	if (FLOW_FDIR_CMP(f1, f2, attr) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l2) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l2_mask) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l3) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l3_mask) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l4) ||
> > 	    FLOW_FDIR_CMP(f1, f2, l4_mask) ||
> > 	    FLOW_FDIR_CMP(f1, f2, actions[0].type))
> > 		return 1;
> > 	if (f1->actions[0].type == RTE_FLOW_ACTION_TYPE_QUEUE &&
> > 	    FLOW_FDIR_CMP(f1, f2, queue))
> > 		return 1;
> > 	return 0;
> > }
> >
> > Thanks,
> > Daniel



More information about the dev mailing list