[dpdk-dev] [EXT] Re: [PATCH] eal: change init macro as exec environment specific

Jerin Jacob Kollanukkaran jerinj at marvell.com
Wed Mar 13 09:44:27 CET 2019


On Wed, 2019-03-13 at 09:16 +0100, Thomas Monjalon wrote:
> 13/03/2019 09:02, Jerin Jacob Kollanukkaran:
> > On Tue, 2019-03-12 at 21:33 +0100, Thomas Monjalon wrote:
> > > 12/03/2019 20:25, Jerin Jacob Kollanukkaran:
> > > > On Fri, 2019-03-01 at 18:28 +0100, Thomas Monjalon wrote:
> > > > > 01/03/2019 18:05, Ferruh Yigit:
> > > > > > On 10/11/2017 3:33 PM, jerin.jacob at caviumnetworks.com
> > > > > > (Jerin
> > > > > > Jacob) wrote:
> > > > > > > From: Thomas Monjalon <thomas at monjalon.net>
> > > > > > > > 07/08/2017 14:04, Jerin Jacob:
> > > > > > > > > baremetal execution environments may have a different
> > > > > > > > > method to enable RTE_INIT instead of using compiler
> > > > > > > > > constructor scheme. Move RTE_INIT* definition under
> > > > > > > > > exec-env to support different execution environments.
> > > > > > > > > 
> > > > > > > > > Signed-off-by: Jerin Jacob <jerin.jacob at
> > > > > > > > > caviumnetworks.com>
> > > > > > > > > ---
> > > > > > > > > 
> > > > > 
> > > > > I am not sure there is a real desire to make DPDK
> > > > > ready for bare-metal (back again).
> > > > > If any of you are aware of a real use-case, we can re-
> > > > > consider.
> > > > 
> > > > Some of the usecases:
> > > > 
> > > > # PCIe endpoint mode aka Smart NIC(Where DPDK runs on PCIe
> > > > card),
> > > > May
> > > > not need to waste one core for Linux. Specially Smart NIC
> > > > market
> > > > has
> > > > less number of cores.
> > > > On the endpoint side, It treats as FW so customer may not have
> > > > access
> > > > to so nobdoy cares it is Linux or baremetal so may need to
> > > > waste
> > > > one
> > > > core for Linux
> > > > 
> > > > # VM case, it possible to have bare metal guest just to save
> > > > one a
> > > > logical core for Linux
> > > > 
> > > > # Some of the RTOS like Zephyr already provide TCP/IP stack and
> > > > good
> > > > subsystems for specific usecases.
> > > > 
> > > > # We are using DPDK for pre silicon validation for SoC mode.
> > > > Bringing
> > > > up linux on emulator takes ages, Baremetal can be used for
> > > > Harware
> > > > verification too.
> > > > 
> > > > 
> > > > IMO, As long as it not limiting the a feature of Linux app, Why
> > > > not
> > > > to
> > > > allow baremetal? I agree with code duplication. I think, it can
> > > > be
> > > > fixed easily, Other than that, Is there any concern?
> > > 
> > > The concern is about the effort required.
> > > Which libc to use? Which dependency is acceptable?
> > 
> > # It should be like FreeBSD or Windows EAL port(Where changes
> > should be
> > in lib/librte_eal/xxxxxx/)
> > # Baremetal libc can be newlibc or musl.
> > # IMO, If bare metal code is open source then the dependency does
> > not
> > matter
> > # if RTOS supports POSIX wrappers, the common code changes will be
> > very
> > minimal.
> > # In house, We have baremetal support as PoC, where 95% of changes
> > are
> > in lib/librte_eal/xxxxxx/ with POSIX wrappers.
> 
> Then maybe you should send your patches so we can decide if it is
> maintainable enough or not.

The  __attribute__((constructor)) only stuff we have issue to support.
The common code changes are related to adapt
__attribute__((constructor)) scheme.

This patch will fix that issue. Other than that there is no common code
changes.i.e everything emulated under lib/librte_eal/new_port/



> 
> 


More information about the dev mailing list