[dpdk-dev] [PATCH] net/mlx5: support IP-in-IP tunnel

Xiaoyu Min jackmin at mellanox.com
Tue May 28 04:04:25 CEST 2019
Previous message: [dpdk-dev] [PATCH] eventdev: optimize Rx adapter event enqueue
Next message: [dpdk-dev] [PATCH] net/mlx5: support matching on ICMP/ICMP6
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Enabled IP-in-IP tunnel type support on DV/DR flow engine.
This includes the following combination:
 - IPv4 over IPv4
 - IPv4 over IPv6
 - IPv6 over IPv4
 - IPv6 over IPv6

MLX5 NIC supports IP-in-IP tunnel via FLEX Parser so
need to make sure fw using FLEX Paser profile 0.

  mlxconfig -d <mst device> -y set FLEX_PARSER_PROFILE_ENABLE=0

Signed-off-by: Xiaoyu Min <jackmin at mellanox.com>
---
 doc/guides/nics/mlx5.rst        | 15 ++++++++++++-
 drivers/net/mlx5/mlx5_flow.c    | 35 +++++++++++++++++++++++++++++++
 drivers/net/mlx5/mlx5_flow.h    |  9 +++++---
 drivers/net/mlx5/mlx5_flow_dv.c | 37 +++++++++++++++++++++++++++++++++
 4 files changed, 92 insertions(+), 4 deletions(-)

diff --git a/doc/guides/nics/mlx5.rst b/doc/guides/nics/mlx5.rst
index 5176aa845c..67377048ae 100644
--- a/doc/guides/nics/mlx5.rst
+++ b/doc/guides/nics/mlx5.rst
@@ -76,7 +76,7 @@ Features
 - RX interrupts.
 - Statistics query including Basic, Extended and per queue.
 - Rx HW timestamp.
-- Tunnel types: VXLAN, L3 VXLAN, VXLAN-GPE, GRE, MPLSoGRE, MPLSoUDP.
+- Tunnel types: VXLAN, L3 VXLAN, VXLAN-GPE, GRE, MPLSoGRE, MPLSoUDP, IP-in-IP.
 - Tunnel HW offloads: packet type, inner/outer RSS, IP and UDP checksum verification.
 - NIC HW offloads: encapsulation (vxlan, gre, mplsoudp, mplsogre), NAT, routing, TTL
   increment/decrement, count, drop, mark. For details please see :ref:`Supported hardware offloads using rte_flow API`.
@@ -518,6 +518,19 @@ Firmware configuration
      IP_OVER_VXLAN_EN                    True(1)
      IP_OVER_VXLAN_PORT                  <udp dport>
 
+- IP-in-IP tunnel enable
+
+   .. code-block:: console
+
+     mlxconfig -d <mst device> set FLEX_PARSER_PROFILE_ENABLE=0
+
+  Verify configurations are set:
+
+   .. code-block:: console
+
+     mlxconfig -d <mst device> query | grep FLEX_PARSER_PROFILE_ENABLE
+     FLEX_PARSER_PROFILE_ENABLE          0
+
 Prerequisites
 -------------
 
diff --git a/drivers/net/mlx5/mlx5_flow.c b/drivers/net/mlx5/mlx5_flow.c
index 98870184d0..66f36f64bf 100644
--- a/drivers/net/mlx5/mlx5_flow.c
+++ b/drivers/net/mlx5/mlx5_flow.c
@@ -1180,6 +1180,7 @@ mlx5_flow_validate_item_ipv4(const struct rte_flow_item *item,
 			     struct rte_flow_error *error)
 {
 	const struct rte_flow_item_ipv4 *mask = item->mask;
+	const struct rte_flow_item_ipv4 *spec = item->spec;
 	const struct rte_flow_item_ipv4 nic_mask = {
 		.hdr = {
 			.src_addr = RTE_BE32(0xffffffff),
@@ -1194,7 +1195,24 @@ mlx5_flow_validate_item_ipv4(const struct rte_flow_item *item,
 	const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
 				      MLX5_FLOW_LAYER_OUTER_L4;
 	int ret;
+	uint8_t next_proto = 0xFF;
 
+	if (item_flags & MLX5_FLOW_LAYER_IPIP) {
+		if (mask && spec)
+			next_proto = mask->hdr.next_proto_id &
+				     spec->hdr.next_proto_id;
+		if (next_proto == IPPROTO_IPIP || next_proto == IPPROTO_IPV6)
+			return rte_flow_error_set(error, EINVAL,
+						  RTE_FLOW_ERROR_TYPE_ITEM,
+						  item,
+						  "multiple tunnel "
+						  "not supported");
+	}
+	if (item_flags & MLX5_FLOW_LAYER_IPV6_ENCAP)
+		return rte_flow_error_set(error, EINVAL,
+					  RTE_FLOW_ERROR_TYPE_ITEM, item,
+					  "wrong tunnel type - IPv6 specified "
+					  "but IPv4 item provided");
 	if (item_flags & l3m)
 		return rte_flow_error_set(error, ENOTSUP,
 					  RTE_FLOW_ERROR_TYPE_ITEM, item,
@@ -1244,6 +1262,7 @@ mlx5_flow_validate_item_ipv6(const struct rte_flow_item *item,
 			     struct rte_flow_error *error)
 {
 	const struct rte_flow_item_ipv6 *mask = item->mask;
+	const struct rte_flow_item_ipv6 *spec = item->spec;
 	const struct rte_flow_item_ipv6 nic_mask = {
 		.hdr = {
 			.src_addr =
@@ -1263,7 +1282,23 @@ mlx5_flow_validate_item_ipv6(const struct rte_flow_item *item,
 	const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
 				      MLX5_FLOW_LAYER_OUTER_L4;
 	int ret;
+	uint8_t next_proto = 0xFF;
 
+	if (item_flags & MLX5_FLOW_LAYER_IPV6_ENCAP) {
+		if (mask && spec)
+			next_proto = mask->hdr.proto & spec->hdr.proto;
+		if (next_proto == IPPROTO_IPIP || next_proto == IPPROTO_IPV6)
+			return rte_flow_error_set(error, EINVAL,
+						  RTE_FLOW_ERROR_TYPE_ITEM,
+						  item,
+						  "multiple tunnel "
+						  "not supported");
+	}
+	if (item_flags & MLX5_FLOW_LAYER_IPIP)
+		return rte_flow_error_set(error, EINVAL,
+					  RTE_FLOW_ERROR_TYPE_ITEM, item,
+					  "wrong tunnel type - IPv4 specified "
+					  "but IPv6 item provided");
 	if (item_flags & l3m)
 		return rte_flow_error_set(error, ENOTSUP,
 					  RTE_FLOW_ERROR_TYPE_ITEM, item,
diff --git a/drivers/net/mlx5/mlx5_flow.h b/drivers/net/mlx5/mlx5_flow.h
index b6654200cb..6501accfe4 100644
--- a/drivers/net/mlx5/mlx5_flow.h
+++ b/drivers/net/mlx5/mlx5_flow.h
@@ -45,10 +45,12 @@
 #define MLX5_FLOW_LAYER_VXLAN_GPE (1u << 13)
 #define MLX5_FLOW_LAYER_GRE (1u << 14)
 #define MLX5_FLOW_LAYER_MPLS (1u << 15)
+#define MLX5_FLOW_LAYER_IPIP (1u << 16)
+#define MLX5_FLOW_LAYER_IPV6_ENCAP (1u << 17)
 
 /* General pattern items bits. */
-#define MLX5_FLOW_ITEM_METADATA (1u << 16)
-#define MLX5_FLOW_ITEM_PORT_ID (1u << 17)
+#define MLX5_FLOW_ITEM_METADATA (1u << 18)
+#define MLX5_FLOW_ITEM_PORT_ID (1u << 19)
 
 /* Outer Masks. */
 #define MLX5_FLOW_LAYER_OUTER_L3 \
@@ -62,7 +64,8 @@
 /* Tunnel Masks. */
 #define MLX5_FLOW_LAYER_TUNNEL \
 	(MLX5_FLOW_LAYER_VXLAN | MLX5_FLOW_LAYER_VXLAN_GPE | \
-	 MLX5_FLOW_LAYER_GRE | MLX5_FLOW_LAYER_MPLS)
+	 MLX5_FLOW_LAYER_GRE | MLX5_FLOW_LAYER_MPLS | \
+	 MLX5_FLOW_LAYER_IPIP | MLX5_FLOW_LAYER_IPV6_ENCAP)
 
 /* Inner Masks. */
 #define MLX5_FLOW_LAYER_INNER_L3 \
diff --git a/drivers/net/mlx5/mlx5_flow_dv.c b/drivers/net/mlx5/mlx5_flow_dv.c
index d096b02bba..1e9a497e7b 100644
--- a/drivers/net/mlx5/mlx5_flow_dv.c
+++ b/drivers/net/mlx5/mlx5_flow_dv.c
@@ -139,6 +139,39 @@ struct field_modify_info modify_tcp[] = {
 	{0, 0, 0},
 };
 
+static void
+mlx5_flow_tunnel_ip_check(const struct rte_flow_item *item, uint64_t *flags)
+{
+	uint8_t next_protocol = 0xFF;
+
+	if (item->mask != NULL) {
+		switch (item->type) {
+		case RTE_FLOW_ITEM_TYPE_IPV4:
+			next_protocol =
+				((const struct rte_flow_item_ipv4 *)
+				 (item->spec))->hdr.next_proto_id;
+			next_protocol &=
+				((const struct rte_flow_item_ipv4 *)
+				 (item->mask))->hdr.next_proto_id;
+			break;
+		case RTE_FLOW_ITEM_TYPE_IPV6:
+			next_protocol =
+				((const struct rte_flow_item_ipv6 *)
+				 (item->spec))->hdr.proto;
+			next_protocol &=
+				((const struct rte_flow_item_ipv6 *)
+				 (item->mask))->hdr.proto;
+			break;
+		default:
+			break;
+		}
+	}
+	if (next_protocol == IPPROTO_IPIP)
+		*flags |= MLX5_FLOW_LAYER_IPIP;
+	if (next_protocol == IPPROTO_IPV6)
+		*flags |= MLX5_FLOW_LAYER_IPV6_ENCAP;
+}
+
 /**
  * Acquire the synchronizing object to protect multithreaded access
  * to shared dv context. Lock occurs only if context is actually
@@ -2127,6 +2160,7 @@ flow_dv_validate(struct rte_eth_dev *dev, const struct rte_flow_attr *attr,
 				/* Reset for inner layer. */
 				next_protocol = 0xff;
 			}
+			mlx5_flow_tunnel_ip_check(items, &last_item);
 			break;
 		case RTE_FLOW_ITEM_TYPE_IPV6:
 			ret = mlx5_flow_validate_item_ipv6(items, item_flags,
@@ -2148,6 +2182,7 @@ flow_dv_validate(struct rte_eth_dev *dev, const struct rte_flow_attr *attr,
 				/* Reset for inner layer. */
 				next_protocol = 0xff;
 			}
+			mlx5_flow_tunnel_ip_check(items, &last_item);
 			break;
 		case RTE_FLOW_ITEM_TYPE_TCP:
 			ret = mlx5_flow_validate_item_tcp
@@ -3953,6 +3988,7 @@ flow_dv_translate(struct rte_eth_dev *dev,
 					 MLX5_IPV4_IBV_RX_HASH);
 			last_item = tunnel ? MLX5_FLOW_LAYER_INNER_L3_IPV4 :
 					     MLX5_FLOW_LAYER_OUTER_L3_IPV4;
+			mlx5_flow_tunnel_ip_check(items, &last_item);
 			break;
 		case RTE_FLOW_ITEM_TYPE_IPV6:
 			flow_dv_translate_item_ipv6(match_mask, match_value,
@@ -3965,6 +4001,7 @@ flow_dv_translate(struct rte_eth_dev *dev,
 					 MLX5_IPV6_IBV_RX_HASH);
 			last_item = tunnel ? MLX5_FLOW_LAYER_INNER_L3_IPV6 :
 					     MLX5_FLOW_LAYER_OUTER_L3_IPV6;
+			mlx5_flow_tunnel_ip_check(items, &last_item);
 			break;
 		case RTE_FLOW_ITEM_TYPE_TCP:
 			flow_dv_translate_item_tcp(match_mask, match_value,
-- 
2.21.0
Previous message: [dpdk-dev] [PATCH] eventdev: optimize Rx adapter event enqueue
Next message: [dpdk-dev] [PATCH] net/mlx5: support matching on ICMP/ICMP6
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
More information about the dev mailing list