[dpdk-dev] [PATCH v2] net/ipn3ke: setup MTU when HW init

[Pei, Andy]

HI xiaolong,

Reply inline.

-----Original Message-----
From: Ye, Xiaolong 
Sent: Wednesday, August 21, 2019 2:16 PM
To: Pei, Andy <andy.pei at intel.com>
Cc: dev at dpdk.org; Xu, Rosen <rosen.xu at intel.com>; Zhang, Tianfei <tianfei.zhang at intel.com>
Subject: Re: [dpdk-dev] [PATCH v2] net/ipn3ke: setup MTU when HW init

On 08/09, Andy Pei wrote:
>set up mtu to the minimun in tx mtu, rx mtu and IPN3KE_MAC_FRAME_SIZE_MAX.
>
>Signed-off-by: Andy Pei <andy.pei at intel.com>
>---
>v2:
>* modify low bound and upper bound.
>
> drivers/net/ipn3ke/ipn3ke_ethdev.c | 97 
> ++++++++++++++++++++++++++++++++++++++
> drivers/net/ipn3ke/ipn3ke_ethdev.h | 19 ++++++++
> 2 files changed, 116 insertions(+)
>
>diff --git a/drivers/net/ipn3ke/ipn3ke_ethdev.c 
>b/drivers/net/ipn3ke/ipn3ke_ethdev.c
>index c226d63..1a6c217 100644
>--- a/drivers/net/ipn3ke/ipn3ke_ethdev.c
>+++ b/drivers/net/ipn3ke/ipn3ke_ethdev.c
>@@ -209,6 +209,100 @@
> 	return 0;
> }
> 
>+static void ipn3ke_10G_mtu_setup
>+(struct ipn3ke_hw *hw, uint32_t mac_num, uint32_t eth_group_sel)

The dpdk convention is:

static void
ipn3ke_10G_mtu_setup(xxx)

OK

>+{
>+	uint32_t tx;
>+	uint32_t rx;
>+	uint32_t tmp;
>+
>+	(*hw->f_mac_read)(hw,
>+			&tx,
>+			IPN3KE_10G_TX_FRAME_MAXLENGTH,
>+			mac_num,
>+			eth_group_sel);

Need to verify whether hw->f_mac_read is NULL or not.
ok
>+
>+	(*hw->f_mac_read)(hw,
>+			&rx,
>+			IPN3KE_10G_RX_FRAME_MAXLENGTH,
>+			mac_num,
>+			eth_group_sel);
>+
>+	tmp = (tx > rx) ? rx : tx;

Can use RTE_MIN

OK

>+	if (tmp < RTE_ETHER_MIN_MTU)
>+		tmp = RTE_ETHER_MIN_MTU;
>+	if (tmp > IPN3KE_MAC_FRAME_SIZE_MAX - IPN3KE_ETH_OVERHEAD)
>+		tmp = IPN3KE_MAC_FRAME_SIZE_MAX - IPN3KE_ETH_OVERHEAD;
>+
>+	(*hw->f_mac_write)(hw,
>+			tmp,
>+			IPN3KE_10G_TX_FRAME_MAXLENGTH,
>+			mac_num,
>+			eth_group_sel);
>+
>+	(*hw->f_mac_write)(hw,
>+			tmp,
>+			IPN3KE_10G_RX_FRAME_MAXLENGTH,
>+			mac_num,
>+			eth_group_sel);

Need to check f_mac_write is not NULL before calling it.
ok
>+}
>+
>+static void ipn3ke_25G_mtu_setup
>+(struct ipn3ke_hw *hw, uint32_t mac_num, uint32_t eth_group_sel) {
>+	uint32_t tx;
>+	uint32_t rx;
>+	uint32_t tmp;
>+
>+	(*hw->f_mac_read)(hw,
>+			&tx,
>+			IPN3KE_25G_MAX_TX_SIZE_CONFIG,
>+			mac_num,
>+			eth_group_sel);
>+
>+	(*hw->f_mac_read)(hw,
>+			&rx,
>+			IPN3KE_25G_MAX_RX_SIZE_CONFIG,
>+			mac_num,
>+			eth_group_sel);
>+
>+	tmp = (tx > rx) ? rx : tx;
>+	if (tmp < RTE_ETHER_MIN_MTU)
>+		tmp = RTE_ETHER_MIN_MTU;
>+	if (tmp > IPN3KE_MAC_FRAME_SIZE_MAX - IPN3KE_ETH_OVERHEAD)
>+		tmp = IPN3KE_MAC_FRAME_SIZE_MAX - IPN3KE_ETH_OVERHEAD;
>+
>+	(*hw->f_mac_write)(hw,
>+			tmp,
>+			IPN3KE_25G_MAX_TX_SIZE_CONFIG,
>+			mac_num,
>+			eth_group_sel);
>+
>+	(*hw->f_mac_write)(hw,
>+			tmp,
>+			IPN3KE_25G_MAX_RX_SIZE_CONFIG,
>+			mac_num,
>+			eth_group_sel);
>+}
>+

ipn3ke_10G_mtu_setup and ipn3ke_25G_mtu_setup share most of the code, please try to refactor to avoid duplicate code.
ok
>+static void
>+ipn3ke_mtu_setup(struct ipn3ke_hw *hw) {
>+	int i;
>+	if (hw->retimer.mac_type == IFPGA_RAWDEV_RETIMER_MAC_TYPE_10GE_XFI) {
>+		for (i = 0; i < hw->port_num; i++) {
>+			ipn3ke_10G_mtu_setup(hw, i, 0);
>+			ipn3ke_10G_mtu_setup(hw, i, 1);
>+		}
>+	} else if (hw->retimer.mac_type ==
>+			IFPGA_RAWDEV_RETIMER_MAC_TYPE_25GE_25GAUI) {
>+		for (i = 0; i < hw->port_num; i++) {
>+			ipn3ke_25G_mtu_setup(hw, i, 0);
>+			ipn3ke_25G_mtu_setup(hw, i, 1);
>+		}
>+	}
>+}
>+
> static int
> ipn3ke_hw_init(struct rte_afu_device *afu_dev,
> 	struct ipn3ke_hw *hw)
>@@ -303,6 +397,9 @@
> 		}
> 	}
> 
>+	/* init mtu */
>+	ipn3ke_mtu_setup(hw);
>+
> 	ret = rte_eth_switch_domain_alloc(&hw->switch_domain_id);
> 	if (ret)
> 		IPN3KE_AFU_PMD_WARN("failed to allocate switch domain for device 
>%d", diff --git a/drivers/net/ipn3ke/ipn3ke_ethdev.h 
>b/drivers/net/ipn3ke/ipn3ke_ethdev.h
>index c7b336b..6419da3 100644
>--- a/drivers/net/ipn3ke/ipn3ke_ethdev.h
>+++ b/drivers/net/ipn3ke/ipn3ke_ethdev.h
>@@ -654,6 +654,25 @@ static inline void _ipn3ke_indrct_write(struct 
>ipn3ke_hw *hw,  #define IPN3KE_MAC_RX_FRAME_MAXLENGTH_MASK \
> 	IPN3KE_MASK(0xFFFF, IPN3KE_MAC_RX_FRAME_MAXLENGTH_SHIFT)
> 
>+/* Additional Feature Register */
>+#define ADD_PHY_CTRL		0x0
>+#define PHY_RESET		BIT(0)
>+/* registers for 25G/40G mac */
>+#define MAC_CONFIG	0x310
>+#define MAC_RESET_MASK	GENMASK(2, 0)
>+
>+#define IPN3KE_MAX_MTU                                               0xffff
>+
>+#define IPN3KE_25G_PHY_PMA_SLOOP                                     0x313
>+#define IPN3KE_25G_TX_FLOW_CTRL                                      0x640
>+#define IPN3KE_25G_MAX_TX_SIZE_CONFIG                                0x407
>+#define IPN3KE_25G_MAX_RX_SIZE_CONFIG                                0x506
>+
>+#define IPN3KE_10G_TX_PAUSE_FRAME_QUANTA                             0x0042
>+#define IPN3KE_10G_TX_PAUSE_FRAME_HOLDOFF                            0x0043
>+#define IPN3KE_10G_TX_FRAME_MAXLENGTH                                0x002C
>+#define IPN3KE_10G_RX_FRAME_MAXLENGTH                                0x00AE
>+
> #define IPN3KE_REGISTER_WIDTH                                        32

I saw some MACRO definitions are not used in this patch.
I copy these MACRO from ipn3ke kernel driver in case we will use later.
If not use currently, I can delete these MACRO.

And by the way, why there is no mtu_set ops for ipn3ke ethdev?
Mtu_set ops is in ipn3ke_representor.c

Thanks,
Xiaolong

> 
> /*Bits[2:0]: Configuration of TX statistics counters:
>--
>1.8.3.1
>