[dpdk-dev] [PATCH] app/testpmd: configure rxd and txd number correctly

[oulijun]

在 2020/4/18 8:42, Ferruh Yigit 写道:
> On 4/17/2020 11:59 AM, Lijun Ou wrote:
>> When users configure rxds and txds by used port config cmd based
>> on testpmd application, it will not be able to configure rxd and
>> txd according to the max capability range supported by the actual
>> NIC hardware. Due testpmd defects, it can only configure a fixed
>> range to 0 to 2048.
>> The final result is that an incorrect printing prompt appears and
>> cannot be applied using rxd && txd according to the actual
>> capabilities supported by the device.
>> In order to solve the above problems, we modify the testpmd. First
>> by calling the rte_eth_dev_info_get api to obtain the max and min
>> rx/tx capability supported by the hns3, and then use this range
>> to compare with the actual value by users configured and make
>> reasonable limitation.
>>
>> Signed-off-by: Lijun Ou <oulijun at huawei.com>
>> Signed-off-by: Huisong Li <lihuisong at huawei.com>
>> Signed-off-by: Wei Hu (Xavier) <xavier.huwei at huawei.com>
> 
> <...>
> 
>> @@ -1212,6 +1383,8 @@ init_config(void)
>>   	lcoreid_t  lc_id;
>>   	uint8_t port_per_socket[RTE_MAX_NUMA_NODES];
>>   	struct rte_gro_param gro_param;
>> +	uint16_t allowed_max_rxd;
>> +	uint16_t allowed_max_txd;
>>   	uint32_t gso_types;
>>   	uint16_t data_size;
>>   	bool warning = 0;
>> @@ -1239,6 +1412,9 @@ init_config(void)
>>   		fwd_lcores[lc_id]->cpuid_idx = lc_id;
>>   	}
>>   
>> +	allowed_max_rxd = RTE_TEST_RX_DESC_MAX;
>> +	allowed_max_txd = RTE_TEST_RX_DESC_MAX;
>> +
>>   	RTE_ETH_FOREACH_DEV(pid) {
>>   		port = &ports[pid];
>>   		/* Apply default TxRx configuration for all ports */
>> @@ -1299,6 +1475,13 @@ init_config(void)
>>   				warning = 1;
>>   			}
>>   		}
>> +
>> +		/* Get the maximum number of txd and rxd per queue. */
>> +		if (port->dev_info.tx_desc_lim.nb_max > allowed_max_rxd)
>> +			allowed_max_txd = port->dev_info.tx_desc_lim.nb_max;
>> +
>> +		if (port->dev_info.rx_desc_lim.nb_max > allowed_max_txd)
>> +			allowed_max_rxd = port->dev_info.rx_desc_lim.nb_max;
>>   	}
>>   
>>   	if (warning)
>> @@ -1317,9 +1500,9 @@ init_config(void)
>>   	if (param_total_num_mbufs)
>>   		nb_mbuf_per_pool = param_total_num_mbufs;
>>   	else {
>> -		nb_mbuf_per_pool = RTE_TEST_RX_DESC_MAX +
>> +		nb_mbuf_per_pool = allowed_max_rxd +
>>   			(nb_lcores * mb_mempool_cache) +
>> -			RTE_TEST_TX_DESC_MAX + MAX_PKT_BURST;
>> +			allowed_max_txd + MAX_PKT_BURST;
> 
> Overall patch looks good, but with above change, for the PMDs that doesn't
> explicitly set 'dev_info.tx_desc_lim.nb_max' gets the default value
> 'UINT16_MAX', like virtual PMDs, and this increases the memmory requirement a lot.
> 
Hi，Ferruh
   Thanks. if some PMDs are not configured according to the 
specifications that are actually supported, does the PMDs driver require 
such a large mbuf by default.
> What do you think to keep "port config all rxd|txd <value>" the fix, but remove
> above nb_mbuf change?
Actually, I agree with your suggestion. But at the same time worry about 
whether mbuf is not enough, when rxd/txd is greater that 
RTE_TEST_TX_DESC_MAX

Thanks
Lijun Ou
> 
> .
>