[dpdk-dev] [PATCH v3 05/11] baseband/acc100: add LDPC processing functions
Xu, Rosen
rosen.xu at intel.com
Sat Aug 29 13:10:54 CEST 2020
Hi,
> -----Original Message-----
> From: dev <dev-bounces at dpdk.org> On Behalf Of Nicolas Chautru
> Sent: Wednesday, August 19, 2020 8:25
> To: dev at dpdk.org; akhil.goyal at nxp.com
> Cc: Richardson, Bruce <bruce.richardson at intel.com>; Chautru, Nicolas
> <nicolas.chautru at intel.com>
> Subject: [dpdk-dev] [PATCH v3 05/11] baseband/acc100: add LDPC
> processing functions
>
> Adding LDPC decode and encode processing operations
>
> Signed-off-by: Nicolas Chautru <nicolas.chautru at intel.com>
> ---
> drivers/baseband/acc100/rte_acc100_pmd.c | 1625
> +++++++++++++++++++++++++++++-
> drivers/baseband/acc100/rte_acc100_pmd.h | 3 +
> 2 files changed, 1626 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/baseband/acc100/rte_acc100_pmd.c
> b/drivers/baseband/acc100/rte_acc100_pmd.c
> index 7a21c57..5f32813 100644
> --- a/drivers/baseband/acc100/rte_acc100_pmd.c
> +++ b/drivers/baseband/acc100/rte_acc100_pmd.c
> @@ -15,6 +15,9 @@
> #include <rte_hexdump.h>
> #include <rte_pci.h>
> #include <rte_bus_pci.h>
> +#ifdef RTE_BBDEV_OFFLOAD_COST
> +#include <rte_cycles.h>
> +#endif
>
> #include <rte_bbdev.h>
> #include <rte_bbdev_pmd.h>
> @@ -449,7 +452,6 @@
> return 0;
> }
>
> -
> /**
> * Report a ACC100 queue index which is free
> * Return 0 to 16k for a valid queue_idx or -1 when no queue is available
> @@ -634,6 +636,46 @@
> struct acc100_device *d = dev->data->dev_private;
>
> static const struct rte_bbdev_op_cap bbdev_capabilities[] = {
> + {
> + .type = RTE_BBDEV_OP_LDPC_ENC,
> + .cap.ldpc_enc = {
> + .capability_flags =
> + RTE_BBDEV_LDPC_RATE_MATCH |
> + RTE_BBDEV_LDPC_CRC_24B_ATTACH
> |
> +
> RTE_BBDEV_LDPC_INTERLEAVER_BYPASS,
> + .num_buffers_src =
> +
> RTE_BBDEV_LDPC_MAX_CODE_BLOCKS,
> + .num_buffers_dst =
> +
> RTE_BBDEV_LDPC_MAX_CODE_BLOCKS,
> + }
> + },
> + {
> + .type = RTE_BBDEV_OP_LDPC_DEC,
> + .cap.ldpc_dec = {
> + .capability_flags =
> + RTE_BBDEV_LDPC_CRC_TYPE_24B_CHECK |
> + RTE_BBDEV_LDPC_CRC_TYPE_24B_DROP |
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_IN_ENABLE |
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_OUT_ENABLE |
> +#ifdef ACC100_EXT_MEM
> +
> RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_IN_ENABLE |
> +
> RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_OUT_ENABLE |
> +#endif
> +
> RTE_BBDEV_LDPC_ITERATION_STOP_ENABLE |
> + RTE_BBDEV_LDPC_DEINTERLEAVER_BYPASS
> |
> + RTE_BBDEV_LDPC_DECODE_BYPASS |
> + RTE_BBDEV_LDPC_DEC_SCATTER_GATHER |
> +
> RTE_BBDEV_LDPC_HARQ_6BIT_COMPRESSION |
> + RTE_BBDEV_LDPC_LLR_COMPRESSION,
> + .llr_size = 8,
> + .llr_decimals = 1,
> + .num_buffers_src =
> +
> RTE_BBDEV_LDPC_MAX_CODE_BLOCKS,
> + .num_buffers_hard_out =
> +
> RTE_BBDEV_LDPC_MAX_CODE_BLOCKS,
> + .num_buffers_soft_out = 0,
> + }
> + },
> RTE_BBDEV_END_OF_CAPABILITIES_LIST()
> };
>
> @@ -669,9 +711,14 @@
> dev_info->cpu_flag_reqs = NULL;
> dev_info->min_alignment = 64;
> dev_info->capabilities = bbdev_capabilities;
> +#ifdef ACC100_EXT_MEM
> dev_info->harq_buffer_size = d->ddr_size;
> +#else
> + dev_info->harq_buffer_size = 0;
> +#endif
> }
>
> +
> static const struct rte_bbdev_ops acc100_bbdev_ops = {
> .setup_queues = acc100_setup_queues,
> .close = acc100_dev_close,
> @@ -696,6 +743,1577 @@
> {.device_id = 0},
> };
>
> +/* Read flag value 0/1 from bitmap */
> +static inline bool
> +check_bit(uint32_t bitmap, uint32_t bitmask)
> +{
> + return bitmap & bitmask;
> +}
> +
> +static inline char *
> +mbuf_append(struct rte_mbuf *m_head, struct rte_mbuf *m, uint16_t len)
> +{
> + if (unlikely(len > rte_pktmbuf_tailroom(m)))
> + return NULL;
> +
> + char *tail = (char *)m->buf_addr + m->data_off + m->data_len;
> + m->data_len = (uint16_t)(m->data_len + len);
> + m_head->pkt_len = (m_head->pkt_len + len);
> + return tail;
> +}
Is it reasonable to direct add data_len of rte_mbuf?
> +/* Compute value of k0.
> + * Based on 3GPP 38.212 Table 5.4.2.1-2
> + * Starting position of different redundancy versions, k0
> + */
> +static inline uint16_t
> +get_k0(uint16_t n_cb, uint16_t z_c, uint8_t bg, uint8_t rv_index)
> +{
> + if (rv_index == 0)
> + return 0;
> + uint16_t n = (bg == 1 ? N_ZC_1 : N_ZC_2) * z_c;
> + if (n_cb == n) {
> + if (rv_index == 1)
> + return (bg == 1 ? K0_1_1 : K0_1_2) * z_c;
> + else if (rv_index == 2)
> + return (bg == 1 ? K0_2_1 : K0_2_2) * z_c;
> + else
> + return (bg == 1 ? K0_3_1 : K0_3_2) * z_c;
> + }
> + /* LBRM case - includes a division by N */
> + if (rv_index == 1)
> + return (((bg == 1 ? K0_1_1 : K0_1_2) * n_cb)
> + / n) * z_c;
> + else if (rv_index == 2)
> + return (((bg == 1 ? K0_2_1 : K0_2_2) * n_cb)
> + / n) * z_c;
> + else
> + return (((bg == 1 ? K0_3_1 : K0_3_2) * n_cb)
> + / n) * z_c;
> +}
> +
> +/* Fill in a frame control word for LDPC encoding. */
> +static inline void
> +acc100_fcw_le_fill(const struct rte_bbdev_enc_op *op,
> + struct acc100_fcw_le *fcw, int num_cb)
> +{
> + fcw->qm = op->ldpc_enc.q_m;
> + fcw->nfiller = op->ldpc_enc.n_filler;
> + fcw->BG = (op->ldpc_enc.basegraph - 1);
> + fcw->Zc = op->ldpc_enc.z_c;
> + fcw->ncb = op->ldpc_enc.n_cb;
> + fcw->k0 = get_k0(fcw->ncb, fcw->Zc, op->ldpc_enc.basegraph,
> + op->ldpc_enc.rv_index);
> + fcw->rm_e = op->ldpc_enc.cb_params.e;
> + fcw->crc_select = check_bit(op->ldpc_enc.op_flags,
> + RTE_BBDEV_LDPC_CRC_24B_ATTACH);
> + fcw->bypass_intlv = check_bit(op->ldpc_enc.op_flags,
> + RTE_BBDEV_LDPC_INTERLEAVER_BYPASS);
> + fcw->mcb_count = num_cb;
> +}
> +
> +/* Fill in a frame control word for LDPC decoding. */
> +static inline void
> +acc100_fcw_ld_fill(const struct rte_bbdev_dec_op *op, struct
> acc100_fcw_ld *fcw,
> + union acc100_harq_layout_data *harq_layout)
> +{
> + uint16_t harq_out_length, harq_in_length, ncb_p, k0_p,
> parity_offset;
> + uint16_t harq_index;
> + uint32_t l;
> + bool harq_prun = false;
> +
> + fcw->qm = op->ldpc_dec.q_m;
> + fcw->nfiller = op->ldpc_dec.n_filler;
> + fcw->BG = (op->ldpc_dec.basegraph - 1);
> + fcw->Zc = op->ldpc_dec.z_c;
> + fcw->ncb = op->ldpc_dec.n_cb;
> + fcw->k0 = get_k0(fcw->ncb, fcw->Zc, op->ldpc_dec.basegraph,
> + op->ldpc_dec.rv_index);
> + if (op->ldpc_dec.code_block_mode == 1)
> + fcw->rm_e = op->ldpc_dec.cb_params.e;
> + else
> + fcw->rm_e = (op->ldpc_dec.tb_params.r <
> + op->ldpc_dec.tb_params.cab) ?
> + op->ldpc_dec.tb_params.ea :
> + op->ldpc_dec.tb_params.eb;
> +
> + fcw->hcin_en = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_HQ_COMBINE_IN_ENABLE);
> + fcw->hcout_en = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_HQ_COMBINE_OUT_ENABLE);
> + fcw->crc_select = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_CRC_TYPE_24B_CHECK);
> + fcw->bypass_dec = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_DECODE_BYPASS);
> + fcw->bypass_intlv = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_DEINTERLEAVER_BYPASS);
> + if (op->ldpc_dec.q_m == 1) {
> + fcw->bypass_intlv = 1;
> + fcw->qm = 2;
> + }
> + fcw->hcin_decomp_mode = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_HARQ_6BIT_COMPRESSION);
> + fcw->hcout_comp_mode = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_HARQ_6BIT_COMPRESSION);
> + fcw->llr_pack_mode = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_LLR_COMPRESSION);
> + harq_index = op->ldpc_dec.harq_combined_output.offset /
> + ACC100_HARQ_OFFSET;
> +#ifdef ACC100_EXT_MEM
> + /* Limit cases when HARQ pruning is valid */
> + harq_prun = ((op->ldpc_dec.harq_combined_output.offset %
> + ACC100_HARQ_OFFSET) == 0) &&
> + (op->ldpc_dec.harq_combined_output.offset <=
> UINT16_MAX
> + * ACC100_HARQ_OFFSET);
> +#endif
> + if (fcw->hcin_en > 0) {
> + harq_in_length = op-
> >ldpc_dec.harq_combined_input.length;
> + if (fcw->hcin_decomp_mode > 0)
> + harq_in_length = harq_in_length * 8 / 6;
> + harq_in_length = RTE_ALIGN(harq_in_length, 64);
> + if ((harq_layout[harq_index].offset > 0) & harq_prun) {
> + rte_bbdev_log_debug("HARQ IN offset unexpected
> for now\n");
> + fcw->hcin_size0 = harq_layout[harq_index].size0;
> + fcw->hcin_offset = harq_layout[harq_index].offset;
> + fcw->hcin_size1 = harq_in_length -
> + harq_layout[harq_index].offset;
> + } else {
> + fcw->hcin_size0 = harq_in_length;
> + fcw->hcin_offset = 0;
> + fcw->hcin_size1 = 0;
> + }
> + } else {
> + fcw->hcin_size0 = 0;
> + fcw->hcin_offset = 0;
> + fcw->hcin_size1 = 0;
> + }
> +
> + fcw->itmax = op->ldpc_dec.iter_max;
> + fcw->itstop = check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_ITERATION_STOP_ENABLE);
> + fcw->synd_precoder = fcw->itstop;
> + /*
> + * These are all implicitly set
> + * fcw->synd_post = 0;
> + * fcw->so_en = 0;
> + * fcw->so_bypass_rm = 0;
> + * fcw->so_bypass_intlv = 0;
> + * fcw->dec_convllr = 0;
> + * fcw->hcout_convllr = 0;
> + * fcw->hcout_size1 = 0;
> + * fcw->so_it = 0;
> + * fcw->hcout_offset = 0;
> + * fcw->negstop_th = 0;
> + * fcw->negstop_it = 0;
> + * fcw->negstop_en = 0;
> + * fcw->gain_i = 1;
> + * fcw->gain_h = 1;
> + */
> + if (fcw->hcout_en > 0) {
> + parity_offset = (op->ldpc_dec.basegraph == 1 ? 20 : 8)
> + * op->ldpc_dec.z_c - op->ldpc_dec.n_filler;
> + k0_p = (fcw->k0 > parity_offset) ?
> + fcw->k0 - op->ldpc_dec.n_filler : fcw->k0;
> + ncb_p = fcw->ncb - op->ldpc_dec.n_filler;
> + l = k0_p + fcw->rm_e;
> + harq_out_length = (uint16_t) fcw->hcin_size0;
> + harq_out_length = RTE_MIN(RTE_MAX(harq_out_length, l),
> ncb_p);
> + harq_out_length = (harq_out_length + 0x3F) & 0xFFC0;
> + if ((k0_p > fcw->hcin_size0 +
> ACC100_HARQ_OFFSET_THRESHOLD) &&
> + harq_prun) {
> + fcw->hcout_size0 = (uint16_t) fcw->hcin_size0;
> + fcw->hcout_offset = k0_p & 0xFFC0;
> + fcw->hcout_size1 = harq_out_length - fcw-
> >hcout_offset;
> + } else {
> + fcw->hcout_size0 = harq_out_length;
> + fcw->hcout_size1 = 0;
> + fcw->hcout_offset = 0;
> + }
> + harq_layout[harq_index].offset = fcw->hcout_offset;
> + harq_layout[harq_index].size0 = fcw->hcout_size0;
> + } else {
> + fcw->hcout_size0 = 0;
> + fcw->hcout_size1 = 0;
> + fcw->hcout_offset = 0;
> + }
> +}
> +
> +/**
> + * Fills descriptor with data pointers of one block type.
> + *
> + * @param desc
> + * Pointer to DMA descriptor.
> + * @param input
> + * Pointer to pointer to input data which will be encoded. It can be changed
> + * and points to next segment in scatter-gather case.
> + * @param offset
> + * Input offset in rte_mbuf structure. It is used for calculating the point
> + * where data is starting.
> + * @param cb_len
> + * Length of currently processed Code Block
> + * @param seg_total_left
> + * It indicates how many bytes still left in segment (mbuf) for further
> + * processing.
> + * @param op_flags
> + * Store information about device capabilities
> + * @param next_triplet
> + * Index for ACC100 DMA Descriptor triplet
> + *
> + * @return
> + * Returns index of next triplet on success, other value if lengths of
> + * pkt and processed cb do not match.
> + *
> + */
> +static inline int
> +acc100_dma_fill_blk_type_in(struct acc100_dma_req_desc *desc,
> + struct rte_mbuf **input, uint32_t *offset, uint32_t cb_len,
> + uint32_t *seg_total_left, int next_triplet)
> +{
> + uint32_t part_len;
> + struct rte_mbuf *m = *input;
> +
> + part_len = (*seg_total_left < cb_len) ? *seg_total_left : cb_len;
> + cb_len -= part_len;
> + *seg_total_left -= part_len;
> +
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(m, *offset);
> + desc->data_ptrs[next_triplet].blen = part_len;
> + desc->data_ptrs[next_triplet].blkid = ACC100_DMA_BLKID_IN;
> + desc->data_ptrs[next_triplet].last = 0;
> + desc->data_ptrs[next_triplet].dma_ext = 0;
> + *offset += part_len;
> + next_triplet++;
> +
> + while (cb_len > 0) {
> + if (next_triplet < ACC100_DMA_MAX_NUM_POINTERS &&
> + m->next != NULL) {
> +
> + m = m->next;
> + *seg_total_left = rte_pktmbuf_data_len(m);
> + part_len = (*seg_total_left < cb_len) ?
> + *seg_total_left :
> + cb_len;
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_mtophys(m);
> + desc->data_ptrs[next_triplet].blen = part_len;
> + desc->data_ptrs[next_triplet].blkid =
> + ACC100_DMA_BLKID_IN;
> + desc->data_ptrs[next_triplet].last = 0;
> + desc->data_ptrs[next_triplet].dma_ext = 0;
> + cb_len -= part_len;
> + *seg_total_left -= part_len;
> + /* Initializing offset for next segment (mbuf) */
> + *offset = part_len;
> + next_triplet++;
> + } else {
> + rte_bbdev_log(ERR,
> + "Some data still left for processing: "
> + "data_left: %u, next_triplet: %u,
> next_mbuf: %p",
> + cb_len, next_triplet, m->next);
> + return -EINVAL;
> + }
> + }
> + /* Storing new mbuf as it could be changed in scatter-gather case*/
> + *input = m;
> +
> + return next_triplet;
> +}
> +
> +/* Fills descriptor with data pointers of one block type.
> + * Returns index of next triplet on success, other value if lengths of
> + * output data and processed mbuf do not match.
> + */
> +static inline int
> +acc100_dma_fill_blk_type_out(struct acc100_dma_req_desc *desc,
> + struct rte_mbuf *output, uint32_t out_offset,
> + uint32_t output_len, int next_triplet, int blk_id)
> +{
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(output, out_offset);
> + desc->data_ptrs[next_triplet].blen = output_len;
> + desc->data_ptrs[next_triplet].blkid = blk_id;
> + desc->data_ptrs[next_triplet].last = 0;
> + desc->data_ptrs[next_triplet].dma_ext = 0;
> + next_triplet++;
> +
> + return next_triplet;
> +}
> +
> +static inline int
> +acc100_dma_desc_le_fill(struct rte_bbdev_enc_op *op,
> + struct acc100_dma_req_desc *desc, struct rte_mbuf **input,
> + struct rte_mbuf *output, uint32_t *in_offset,
> + uint32_t *out_offset, uint32_t *out_length,
> + uint32_t *mbuf_total_left, uint32_t *seg_total_left)
> +{
> + int next_triplet = 1; /* FCW already done */
> + uint16_t K, in_length_in_bits, in_length_in_bytes;
> + struct rte_bbdev_op_ldpc_enc *enc = &op->ldpc_enc;
> +
> + desc->word0 = ACC100_DMA_DESC_TYPE;
> + desc->word1 = 0; /**< Timestamp could be disabled */
> + desc->word2 = 0;
> + desc->word3 = 0;
> + desc->numCBs = 1;
> +
> + K = (enc->basegraph == 1 ? 22 : 10) * enc->z_c;
> + in_length_in_bits = K - enc->n_filler;
> + if ((enc->op_flags & RTE_BBDEV_LDPC_CRC_24A_ATTACH) ||
> + (enc->op_flags &
> RTE_BBDEV_LDPC_CRC_24B_ATTACH))
> + in_length_in_bits -= 24;
> + in_length_in_bytes = in_length_in_bits >> 3;
> +
> + if (unlikely((*mbuf_total_left == 0) ||
> + (*mbuf_total_left < in_length_in_bytes))) {
> + rte_bbdev_log(ERR,
> + "Mismatch between mbuf length and
> included CB sizes: mbuf len %u, cb len %u",
> + *mbuf_total_left, in_length_in_bytes);
> + return -1;
> + }
> +
> + next_triplet = acc100_dma_fill_blk_type_in(desc, input, in_offset,
> + in_length_in_bytes,
> + seg_total_left, next_triplet);
> + if (unlikely(next_triplet < 0)) {
> + rte_bbdev_log(ERR,
> + "Mismatch between data to process and
> mbuf data length in bbdev_op: %p",
> + op);
> + return -1;
> + }
> + desc->data_ptrs[next_triplet - 1].last = 1;
> + desc->m2dlen = next_triplet;
> + *mbuf_total_left -= in_length_in_bytes;
> +
> + /* Set output length */
> + /* Integer round up division by 8 */
> + *out_length = (enc->cb_params.e + 7) >> 3;
> +
> + next_triplet = acc100_dma_fill_blk_type_out(desc, output,
> *out_offset,
> + *out_length, next_triplet,
> ACC100_DMA_BLKID_OUT_ENC);
> + if (unlikely(next_triplet < 0)) {
> + rte_bbdev_log(ERR,
> + "Mismatch between data to process and
> mbuf data length in bbdev_op: %p",
> + op);
> + return -1;
> + }
> + op->ldpc_enc.output.length += *out_length;
> + *out_offset += *out_length;
> + desc->data_ptrs[next_triplet - 1].last = 1;
> + desc->data_ptrs[next_triplet - 1].dma_ext = 0;
> + desc->d2mlen = next_triplet - desc->m2dlen;
> +
> + desc->op_addr = op;
> +
> + return 0;
> +}
> +
> +static inline int
> +acc100_dma_desc_ld_fill(struct rte_bbdev_dec_op *op,
> + struct acc100_dma_req_desc *desc,
> + struct rte_mbuf **input, struct rte_mbuf *h_output,
> + uint32_t *in_offset, uint32_t *h_out_offset,
> + uint32_t *h_out_length, uint32_t *mbuf_total_left,
> + uint32_t *seg_total_left,
> + struct acc100_fcw_ld *fcw)
> +{
> + struct rte_bbdev_op_ldpc_dec *dec = &op->ldpc_dec;
> + int next_triplet = 1; /* FCW already done */
> + uint32_t input_length;
> + uint16_t output_length, crc24_overlap = 0;
> + uint16_t sys_cols, K, h_p_size, h_np_size;
> + bool h_comp = check_bit(dec->op_flags,
> + RTE_BBDEV_LDPC_HARQ_6BIT_COMPRESSION);
> +
> + desc->word0 = ACC100_DMA_DESC_TYPE;
> + desc->word1 = 0; /**< Timestamp could be disabled */
> + desc->word2 = 0;
> + desc->word3 = 0;
> + desc->numCBs = 1;
> +
> + if (check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_CRC_TYPE_24B_DROP))
> + crc24_overlap = 24;
> +
> + /* Compute some LDPC BG lengths */
> + input_length = dec->cb_params.e;
> + if (check_bit(op->ldpc_dec.op_flags,
> + RTE_BBDEV_LDPC_LLR_COMPRESSION))
> + input_length = (input_length * 3 + 3) / 4;
> + sys_cols = (dec->basegraph == 1) ? 22 : 10;
> + K = sys_cols * dec->z_c;
> + output_length = K - dec->n_filler - crc24_overlap;
> +
> + if (unlikely((*mbuf_total_left == 0) ||
> + (*mbuf_total_left < input_length))) {
> + rte_bbdev_log(ERR,
> + "Mismatch between mbuf length and
> included CB sizes: mbuf len %u, cb len %u",
> + *mbuf_total_left, input_length);
> + return -1;
> + }
> +
> + next_triplet = acc100_dma_fill_blk_type_in(desc, input,
> + in_offset, input_length,
> + seg_total_left, next_triplet);
> +
> + if (unlikely(next_triplet < 0)) {
> + rte_bbdev_log(ERR,
> + "Mismatch between data to process and
> mbuf data length in bbdev_op: %p",
> + op);
> + return -1;
> + }
> +
> + if (check_bit(op->ldpc_dec.op_flags,
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_IN_ENABLE)) {
> + h_p_size = fcw->hcin_size0 + fcw->hcin_size1;
> + if (h_comp)
> + h_p_size = (h_p_size * 3 + 3) / 4;
> + desc->data_ptrs[next_triplet].address =
> + dec->harq_combined_input.offset;
> + desc->data_ptrs[next_triplet].blen = h_p_size;
> + desc->data_ptrs[next_triplet].blkid =
> ACC100_DMA_BLKID_IN_HARQ;
> + desc->data_ptrs[next_triplet].dma_ext = 1;
> +#ifndef ACC100_EXT_MEM
> + acc100_dma_fill_blk_type_out(
> + desc,
> + op->ldpc_dec.harq_combined_input.data,
> + op->ldpc_dec.harq_combined_input.offset,
> + h_p_size,
> + next_triplet,
> + ACC100_DMA_BLKID_IN_HARQ);
> +#endif
> + next_triplet++;
> + }
> +
> + desc->data_ptrs[next_triplet - 1].last = 1;
> + desc->m2dlen = next_triplet;
> + *mbuf_total_left -= input_length;
> +
> + next_triplet = acc100_dma_fill_blk_type_out(desc, h_output,
> + *h_out_offset, output_length >> 3, next_triplet,
> + ACC100_DMA_BLKID_OUT_HARD);
> + if (unlikely(next_triplet < 0)) {
> + rte_bbdev_log(ERR,
> + "Mismatch between data to process and
> mbuf data length in bbdev_op: %p",
> + op);
> + return -1;
> + }
> +
> + if (check_bit(op->ldpc_dec.op_flags,
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_OUT_ENABLE)) {
> + /* Pruned size of the HARQ */
> + h_p_size = fcw->hcout_size0 + fcw->hcout_size1;
> + /* Non-Pruned size of the HARQ */
> + h_np_size = fcw->hcout_offset > 0 ?
> + fcw->hcout_offset + fcw->hcout_size1 :
> + h_p_size;
> + if (h_comp) {
> + h_np_size = (h_np_size * 3 + 3) / 4;
> + h_p_size = (h_p_size * 3 + 3) / 4;
> + }
> + dec->harq_combined_output.length = h_np_size;
> + desc->data_ptrs[next_triplet].address =
> + dec->harq_combined_output.offset;
> + desc->data_ptrs[next_triplet].blen = h_p_size;
> + desc->data_ptrs[next_triplet].blkid =
> ACC100_DMA_BLKID_OUT_HARQ;
> + desc->data_ptrs[next_triplet].dma_ext = 1;
> +#ifndef ACC100_EXT_MEM
> + acc100_dma_fill_blk_type_out(
> + desc,
> + dec->harq_combined_output.data,
> + dec->harq_combined_output.offset,
> + h_p_size,
> + next_triplet,
> + ACC100_DMA_BLKID_OUT_HARQ);
> +#endif
> + next_triplet++;
> + }
> +
> + *h_out_length = output_length >> 3;
> + dec->hard_output.length += *h_out_length;
> + *h_out_offset += *h_out_length;
> + desc->data_ptrs[next_triplet - 1].last = 1;
> + desc->d2mlen = next_triplet - desc->m2dlen;
> +
> + desc->op_addr = op;
> +
> + return 0;
> +}
> +
> +static inline void
> +acc100_dma_desc_ld_update(struct rte_bbdev_dec_op *op,
> + struct acc100_dma_req_desc *desc,
> + struct rte_mbuf *input, struct rte_mbuf *h_output,
> + uint32_t *in_offset, uint32_t *h_out_offset,
> + uint32_t *h_out_length,
> + union acc100_harq_layout_data *harq_layout)
> +{
> + int next_triplet = 1; /* FCW already done */
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(input, *in_offset);
> + next_triplet++;
> +
> + if (check_bit(op->ldpc_dec.op_flags,
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_IN_ENABLE)) {
> + struct rte_bbdev_op_data hi = op-
> >ldpc_dec.harq_combined_input;
> + desc->data_ptrs[next_triplet].address = hi.offset;
> +#ifndef ACC100_EXT_MEM
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(hi.data, hi.offset);
> +#endif
> + next_triplet++;
> + }
> +
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(h_output, *h_out_offset);
> + *h_out_length = desc->data_ptrs[next_triplet].blen;
> + next_triplet++;
> +
> + if (check_bit(op->ldpc_dec.op_flags,
> +
> RTE_BBDEV_LDPC_HQ_COMBINE_OUT_ENABLE)) {
> + desc->data_ptrs[next_triplet].address =
> + op->ldpc_dec.harq_combined_output.offset;
> + /* Adjust based on previous operation */
> + struct rte_bbdev_dec_op *prev_op = desc->op_addr;
> + op->ldpc_dec.harq_combined_output.length =
> + prev_op-
> >ldpc_dec.harq_combined_output.length;
> + int16_t hq_idx = op-
> >ldpc_dec.harq_combined_output.offset /
> + ACC100_HARQ_OFFSET;
> + int16_t prev_hq_idx =
> + prev_op-
> >ldpc_dec.harq_combined_output.offset
> + / ACC100_HARQ_OFFSET;
> + harq_layout[hq_idx].val = harq_layout[prev_hq_idx].val;
> +#ifndef ACC100_EXT_MEM
> + struct rte_bbdev_op_data ho =
> + op->ldpc_dec.harq_combined_output;
> + desc->data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(ho.data, ho.offset);
> +#endif
> + next_triplet++;
> + }
> +
> + op->ldpc_dec.hard_output.length += *h_out_length;
> + desc->op_addr = op;
> +}
> +
> +
> +/* Enqueue a number of operations to HW and update software rings */
> +static inline void
> +acc100_dma_enqueue(struct acc100_queue *q, uint16_t n,
> + struct rte_bbdev_stats *queue_stats)
> +{
> + union acc100_enqueue_reg_fmt enq_req;
> +#ifdef RTE_BBDEV_OFFLOAD_COST
> + uint64_t start_time = 0;
> + queue_stats->acc_offload_cycles = 0;
> + RTE_SET_USED(queue_stats);
> +#else
> + RTE_SET_USED(queue_stats);
> +#endif
> +
> + enq_req.val = 0;
> + /* Setting offset, 100b for 256 DMA Desc */
> + enq_req.addr_offset = ACC100_DESC_OFFSET;
> +
> + /* Split ops into batches */
> + do {
> + union acc100_dma_desc *desc;
> + uint16_t enq_batch_size;
> + uint64_t offset;
> + rte_iova_t req_elem_addr;
> +
> + enq_batch_size = RTE_MIN(n, MAX_ENQ_BATCH_SIZE);
> +
> + /* Set flag on last descriptor in a batch */
> + desc = q->ring_addr + ((q->sw_ring_head + enq_batch_size -
> 1) &
> + q->sw_ring_wrap_mask);
> + desc->req.last_desc_in_batch = 1;
> +
> + /* Calculate the 1st descriptor's address */
> + offset = ((q->sw_ring_head & q->sw_ring_wrap_mask) *
> + sizeof(union acc100_dma_desc));
> + req_elem_addr = q->ring_addr_phys + offset;
> +
> + /* Fill enqueue struct */
> + enq_req.num_elem = enq_batch_size;
> + /* low 6 bits are not needed */
> + enq_req.req_elem_addr = (uint32_t)(req_elem_addr >> 6);
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + rte_memdump(stderr, "Req sdone", desc, sizeof(*desc));
> +#endif
> + rte_bbdev_log_debug(
> + "Enqueue %u reqs (phys %#"PRIx64") to
> reg %p",
> + enq_batch_size,
> + req_elem_addr,
> + (void *)q->mmio_reg_enqueue);
> +
> + rte_wmb();
> +
> +#ifdef RTE_BBDEV_OFFLOAD_COST
> + /* Start time measurement for enqueue function offload. */
> + start_time = rte_rdtsc_precise();
> +#endif
> + rte_bbdev_log(DEBUG, "Debug : MMIO Enqueue");
> + mmio_write(q->mmio_reg_enqueue, enq_req.val);
> +
> +#ifdef RTE_BBDEV_OFFLOAD_COST
> + queue_stats->acc_offload_cycles +=
> + rte_rdtsc_precise() - start_time;
> +#endif
> +
> + q->aq_enqueued++;
> + q->sw_ring_head += enq_batch_size;
> + n -= enq_batch_size;
> +
> + } while (n);
> +
> +
> +}
> +
> +/* Enqueue one encode operations for ACC100 device in CB mode */
> +static inline int
> +enqueue_ldpc_enc_n_op_cb(struct acc100_queue *q, struct
> rte_bbdev_enc_op **ops,
> + uint16_t total_enqueued_cbs, int16_t num)
> +{
> + union acc100_dma_desc *desc = NULL;
> + uint32_t out_length;
> + struct rte_mbuf *output_head, *output;
> + int i, next_triplet;
> + uint16_t in_length_in_bytes;
> + struct rte_bbdev_op_ldpc_enc *enc = &ops[0]->ldpc_enc;
> +
> + uint16_t desc_idx = ((q->sw_ring_head + total_enqueued_cbs)
> + & q->sw_ring_wrap_mask);
> + desc = q->ring_addr + desc_idx;
> + acc100_fcw_le_fill(ops[0], &desc->req.fcw_le, num);
> +
> + /** This could be done at polling */
> + desc->req.word0 = ACC100_DMA_DESC_TYPE;
> + desc->req.word1 = 0; /**< Timestamp could be disabled */
> + desc->req.word2 = 0;
> + desc->req.word3 = 0;
> + desc->req.numCBs = num;
> +
> + in_length_in_bytes = ops[0]->ldpc_enc.input.data->data_len;
> + out_length = (enc->cb_params.e + 7) >> 3;
> + desc->req.m2dlen = 1 + num;
> + desc->req.d2mlen = num;
> + next_triplet = 1;
> +
> + for (i = 0; i < num; i++) {
> + desc->req.data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(ops[i]-
> >ldpc_enc.input.data, 0);
> + desc->req.data_ptrs[next_triplet].blen = in_length_in_bytes;
> + next_triplet++;
> + desc->req.data_ptrs[next_triplet].address =
> + rte_pktmbuf_iova_offset(
> + ops[i]->ldpc_enc.output.data, 0);
> + desc->req.data_ptrs[next_triplet].blen = out_length;
> + next_triplet++;
> + ops[i]->ldpc_enc.output.length = out_length;
> + output_head = output = ops[i]->ldpc_enc.output.data;
> + mbuf_append(output_head, output, out_length);
> + output->data_len = out_length;
> + }
> +
> + desc->req.op_addr = ops[0];
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + rte_memdump(stderr, "FCW", &desc->req.fcw_le,
> + sizeof(desc->req.fcw_le) - 8);
> + rte_memdump(stderr, "Req Desc.", desc, sizeof(*desc));
> +#endif
> +
> + /* One CB (one op) was successfully prepared to enqueue */
> + return num;
> +}
> +
> +/* Enqueue one encode operations for ACC100 device in CB mode */
> +static inline int
> +enqueue_ldpc_enc_one_op_cb(struct acc100_queue *q, struct
> rte_bbdev_enc_op *op,
> + uint16_t total_enqueued_cbs)
> +{
> + union acc100_dma_desc *desc = NULL;
> + int ret;
> + uint32_t in_offset, out_offset, out_length, mbuf_total_left,
> + seg_total_left;
> + struct rte_mbuf *input, *output_head, *output;
> +
> + uint16_t desc_idx = ((q->sw_ring_head + total_enqueued_cbs)
> + & q->sw_ring_wrap_mask);
> + desc = q->ring_addr + desc_idx;
> + acc100_fcw_le_fill(op, &desc->req.fcw_le, 1);
> +
> + input = op->ldpc_enc.input.data;
> + output_head = output = op->ldpc_enc.output.data;
> + in_offset = op->ldpc_enc.input.offset;
> + out_offset = op->ldpc_enc.output.offset;
> + out_length = 0;
> + mbuf_total_left = op->ldpc_enc.input.length;
> + seg_total_left = rte_pktmbuf_data_len(op->ldpc_enc.input.data)
> + - in_offset;
> +
> + ret = acc100_dma_desc_le_fill(op, &desc->req, &input, output,
> + &in_offset, &out_offset, &out_length,
> &mbuf_total_left,
> + &seg_total_left);
> +
> + if (unlikely(ret < 0))
> + return ret;
> +
> + mbuf_append(output_head, output, out_length);
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + rte_memdump(stderr, "FCW", &desc->req.fcw_le,
> + sizeof(desc->req.fcw_le) - 8);
> + rte_memdump(stderr, "Req Desc.", desc, sizeof(*desc));
> +
> + /* Check if any data left after processing one CB */
> + if (mbuf_total_left != 0) {
> + rte_bbdev_log(ERR,
> + "Some date still left after processing one CB:
> mbuf_total_left = %u",
> + mbuf_total_left);
> + return -EINVAL;
> + }
> +#endif
> + /* One CB (one op) was successfully prepared to enqueue */
> + return 1;
> +}
> +
> +/** Enqueue one decode operations for ACC100 device in CB mode */
> +static inline int
> +enqueue_ldpc_dec_one_op_cb(struct acc100_queue *q, struct
> rte_bbdev_dec_op *op,
> + uint16_t total_enqueued_cbs, bool same_op)
> +{
> + int ret;
> +
> + union acc100_dma_desc *desc;
> + uint16_t desc_idx = ((q->sw_ring_head + total_enqueued_cbs)
> + & q->sw_ring_wrap_mask);
> + desc = q->ring_addr + desc_idx;
> + struct rte_mbuf *input, *h_output_head, *h_output;
> + uint32_t in_offset, h_out_offset, h_out_length, mbuf_total_left;
> + input = op->ldpc_dec.input.data;
> + h_output_head = h_output = op->ldpc_dec.hard_output.data;
> + in_offset = op->ldpc_dec.input.offset;
> + h_out_offset = op->ldpc_dec.hard_output.offset;
> + mbuf_total_left = op->ldpc_dec.input.length;
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + if (unlikely(input == NULL)) {
> + rte_bbdev_log(ERR, "Invalid mbuf pointer");
> + return -EFAULT;
> + }
> +#endif
> + union acc100_harq_layout_data *harq_layout = q->d->harq_layout;
> +
> + if (same_op) {
> + union acc100_dma_desc *prev_desc;
> + desc_idx = ((q->sw_ring_head + total_enqueued_cbs - 1)
> + & q->sw_ring_wrap_mask);
> + prev_desc = q->ring_addr + desc_idx;
> + uint8_t *prev_ptr = (uint8_t *) prev_desc;
> + uint8_t *new_ptr = (uint8_t *) desc;
> + /* Copy first 4 words and BDESCs */
> + rte_memcpy(new_ptr, prev_ptr, 16);
> + rte_memcpy(new_ptr + 36, prev_ptr + 36, 40);
> + desc->req.op_addr = prev_desc->req.op_addr;
> + /* Copy FCW */
> + rte_memcpy(new_ptr + ACC100_DESC_FCW_OFFSET,
> + prev_ptr + ACC100_DESC_FCW_OFFSET,
> + ACC100_FCW_LD_BLEN);
> + acc100_dma_desc_ld_update(op, &desc->req, input,
> h_output,
> + &in_offset, &h_out_offset,
> + &h_out_length, harq_layout);
> + } else {
> + struct acc100_fcw_ld *fcw;
> + uint32_t seg_total_left;
> + fcw = &desc->req.fcw_ld;
> + acc100_fcw_ld_fill(op, fcw, harq_layout);
> +
> + /* Special handling when overusing mbuf */
> + if (fcw->rm_e < MAX_E_MBUF)
> + seg_total_left = rte_pktmbuf_data_len(input)
> + - in_offset;
> + else
> + seg_total_left = fcw->rm_e;
> +
> + ret = acc100_dma_desc_ld_fill(op, &desc->req, &input,
> h_output,
> + &in_offset, &h_out_offset,
> + &h_out_length, &mbuf_total_left,
> + &seg_total_left, fcw);
> + if (unlikely(ret < 0))
> + return ret;
> + }
> +
> + /* Hard output */
> + mbuf_append(h_output_head, h_output, h_out_length);
> +#ifndef ACC100_EXT_MEM
> + if (op->ldpc_dec.harq_combined_output.length > 0) {
> + /* Push the HARQ output into host memory */
> + struct rte_mbuf *hq_output_head, *hq_output;
> + hq_output_head = op-
> >ldpc_dec.harq_combined_output.data;
> + hq_output = op->ldpc_dec.harq_combined_output.data;
> + mbuf_append(hq_output_head, hq_output,
> + op-
> >ldpc_dec.harq_combined_output.length);
> + }
> +#endif
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + rte_memdump(stderr, "FCW", &desc->req.fcw_ld,
> + sizeof(desc->req.fcw_ld) - 8);
> + rte_memdump(stderr, "Req Desc.", desc, sizeof(*desc));
> +#endif
> +
> + /* One CB (one op) was successfully prepared to enqueue */
> + return 1;
> +}
> +
> +
> +/* Enqueue one decode operations for ACC100 device in TB mode */
> +static inline int
> +enqueue_ldpc_dec_one_op_tb(struct acc100_queue *q, struct
> rte_bbdev_dec_op *op,
> + uint16_t total_enqueued_cbs, uint8_t cbs_in_tb)
> +{
> + union acc100_dma_desc *desc = NULL;
> + int ret;
> + uint8_t r, c;
> + uint32_t in_offset, h_out_offset,
> + h_out_length, mbuf_total_left, seg_total_left;
> + struct rte_mbuf *input, *h_output_head, *h_output;
> + uint16_t current_enqueued_cbs = 0;
> +
> + uint16_t desc_idx = ((q->sw_ring_head + total_enqueued_cbs)
> + & q->sw_ring_wrap_mask);
> + desc = q->ring_addr + desc_idx;
> + uint64_t fcw_offset = (desc_idx << 8) + ACC100_DESC_FCW_OFFSET;
> + union acc100_harq_layout_data *harq_layout = q->d->harq_layout;
> + acc100_fcw_ld_fill(op, &desc->req.fcw_ld, harq_layout);
> +
> + input = op->ldpc_dec.input.data;
> + h_output_head = h_output = op->ldpc_dec.hard_output.data;
> + in_offset = op->ldpc_dec.input.offset;
> + h_out_offset = op->ldpc_dec.hard_output.offset;
> + h_out_length = 0;
> + mbuf_total_left = op->ldpc_dec.input.length;
> + c = op->ldpc_dec.tb_params.c;
> + r = op->ldpc_dec.tb_params.r;
> +
> + while (mbuf_total_left > 0 && r < c) {
> +
> + seg_total_left = rte_pktmbuf_data_len(input) - in_offset;
> +
> + /* Set up DMA descriptor */
> + desc = q->ring_addr + ((q->sw_ring_head +
> total_enqueued_cbs)
> + & q->sw_ring_wrap_mask);
> + desc->req.data_ptrs[0].address = q->ring_addr_phys +
> fcw_offset;
> + desc->req.data_ptrs[0].blen = ACC100_FCW_LD_BLEN;
> + ret = acc100_dma_desc_ld_fill(op, &desc->req, &input,
> + h_output, &in_offset, &h_out_offset,
> + &h_out_length,
> + &mbuf_total_left, &seg_total_left,
> + &desc->req.fcw_ld);
> +
> + if (unlikely(ret < 0))
> + return ret;
> +
> + /* Hard output */
> + mbuf_append(h_output_head, h_output, h_out_length);
> +
> + /* Set total number of CBs in TB */
> + desc->req.cbs_in_tb = cbs_in_tb;
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + rte_memdump(stderr, "FCW", &desc->req.fcw_td,
> + sizeof(desc->req.fcw_td) - 8);
> + rte_memdump(stderr, "Req Desc.", desc, sizeof(*desc));
> +#endif
> +
> + if (seg_total_left == 0) {
> + /* Go to the next mbuf */
> + input = input->next;
> + in_offset = 0;
> + h_output = h_output->next;
> + h_out_offset = 0;
> + }
> + total_enqueued_cbs++;
> + current_enqueued_cbs++;
> + r++;
> + }
> +
> + if (unlikely(desc == NULL))
> + return current_enqueued_cbs;
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + /* Check if any CBs left for processing */
> + if (mbuf_total_left != 0) {
> + rte_bbdev_log(ERR,
> + "Some date still left for processing:
> mbuf_total_left = %u",
> + mbuf_total_left);
> + return -EINVAL;
> + }
> +#endif
> + /* Set SDone on last CB descriptor for TB mode */
> + desc->req.sdone_enable = 1;
> + desc->req.irq_enable = q->irq_enable;
> +
> + return current_enqueued_cbs;
> +}
> +
> +
> +/* Calculates number of CBs in processed encoder TB based on 'r' and input
> + * length.
> + */
> +static inline uint8_t
> +get_num_cbs_in_tb_enc(struct rte_bbdev_op_turbo_enc *turbo_enc)
> +{
> + uint8_t c, c_neg, r, crc24_bits = 0;
> + uint16_t k, k_neg, k_pos;
> + uint8_t cbs_in_tb = 0;
> + int32_t length;
> +
> + length = turbo_enc->input.length;
> + r = turbo_enc->tb_params.r;
> + c = turbo_enc->tb_params.c;
> + c_neg = turbo_enc->tb_params.c_neg;
> + k_neg = turbo_enc->tb_params.k_neg;
> + k_pos = turbo_enc->tb_params.k_pos;
> + crc24_bits = 0;
> + if (check_bit(turbo_enc->op_flags,
> RTE_BBDEV_TURBO_CRC_24B_ATTACH))
> + crc24_bits = 24;
> + while (length > 0 && r < c) {
> + k = (r < c_neg) ? k_neg : k_pos;
> + length -= (k - crc24_bits) >> 3;
> + r++;
> + cbs_in_tb++;
> + }
> +
> + return cbs_in_tb;
> +}
> +
> +/* Calculates number of CBs in processed decoder TB based on 'r' and input
> + * length.
> + */
> +static inline uint16_t
> +get_num_cbs_in_tb_dec(struct rte_bbdev_op_turbo_dec *turbo_dec)
> +{
> + uint8_t c, c_neg, r = 0;
> + uint16_t kw, k, k_neg, k_pos, cbs_in_tb = 0;
> + int32_t length;
> +
> + length = turbo_dec->input.length;
> + r = turbo_dec->tb_params.r;
> + c = turbo_dec->tb_params.c;
> + c_neg = turbo_dec->tb_params.c_neg;
> + k_neg = turbo_dec->tb_params.k_neg;
> + k_pos = turbo_dec->tb_params.k_pos;
> + while (length > 0 && r < c) {
> + k = (r < c_neg) ? k_neg : k_pos;
> + kw = RTE_ALIGN_CEIL(k + 4, 32) * 3;
> + length -= kw;
> + r++;
> + cbs_in_tb++;
> + }
> +
> + return cbs_in_tb;
> +}
> +
> +/* Calculates number of CBs in processed decoder TB based on 'r' and input
> + * length.
> + */
> +static inline uint16_t
> +get_num_cbs_in_tb_ldpc_dec(struct rte_bbdev_op_ldpc_dec *ldpc_dec)
> +{
> + uint16_t r, cbs_in_tb = 0;
> + int32_t length = ldpc_dec->input.length;
> + r = ldpc_dec->tb_params.r;
> + while (length > 0 && r < ldpc_dec->tb_params.c) {
> + length -= (r < ldpc_dec->tb_params.cab) ?
> + ldpc_dec->tb_params.ea :
> + ldpc_dec->tb_params.eb;
> + r++;
> + cbs_in_tb++;
> + }
> + return cbs_in_tb;
> +}
> +
> +/* Check we can mux encode operations with common FCW */
> +static inline bool
> +check_mux(struct rte_bbdev_enc_op **ops, uint16_t num) {
> + uint16_t i;
> + if (num == 1)
> + return false;
> + for (i = 1; i < num; ++i) {
> + /* Only mux compatible code blocks */
> + if (memcmp((uint8_t *)(&ops[i]->ldpc_enc) + ENC_OFFSET,
> + (uint8_t *)(&ops[0]->ldpc_enc) +
> ENC_OFFSET,
> + CMP_ENC_SIZE) != 0)
> + return false;
> + }
> + return true;
> +}
> +
> +/** Enqueue encode operations for ACC100 device in CB mode. */
> +static inline uint16_t
> +acc100_enqueue_ldpc_enc_cb(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_enc_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + int32_t avail = q->sw_ring_depth + q->sw_ring_tail - q-
> >sw_ring_head;
> + uint16_t i = 0;
> + union acc100_dma_desc *desc;
> + int ret, desc_idx = 0;
> + int16_t enq, left = num;
> +
> + while (left > 0) {
> + if (unlikely(avail - 1 < 0))
> + break;
> + avail--;
> + enq = RTE_MIN(left, MUX_5GDL_DESC);
> + if (check_mux(&ops[i], enq)) {
> + ret = enqueue_ldpc_enc_n_op_cb(q, &ops[i],
> + desc_idx, enq);
> + if (ret < 0)
> + break;
> + i += enq;
> + } else {
> + ret = enqueue_ldpc_enc_one_op_cb(q, ops[i],
> desc_idx);
> + if (ret < 0)
> + break;
> + i++;
> + }
> + desc_idx++;
> + left = num - i;
> + }
> +
> + if (unlikely(i == 0))
> + return 0; /* Nothing to enqueue */
> +
> + /* Set SDone in last CB in enqueued ops for CB mode*/
> + desc = q->ring_addr + ((q->sw_ring_head + desc_idx - 1)
> + & q->sw_ring_wrap_mask);
> + desc->req.sdone_enable = 1;
> + desc->req.irq_enable = q->irq_enable;
> +
> + acc100_dma_enqueue(q, desc_idx, &q_data->queue_stats);
> +
> + /* Update stats */
> + q_data->queue_stats.enqueued_count += i;
> + q_data->queue_stats.enqueue_err_count += num - i;
> +
> + return i;
> +}
> +
> +/* Enqueue encode operations for ACC100 device. */
> +static uint16_t
> +acc100_enqueue_ldpc_enc(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_enc_op **ops, uint16_t num)
> +{
> + if (unlikely(num == 0))
> + return 0;
> + return acc100_enqueue_ldpc_enc_cb(q_data, ops, num);
> +}
> +
> +/* Check we can mux encode operations with common FCW */
> +static inline bool
> +cmp_ldpc_dec_op(struct rte_bbdev_dec_op **ops) {
> + /* Only mux compatible code blocks */
> + if (memcmp((uint8_t *)(&ops[0]->ldpc_dec) + DEC_OFFSET,
> + (uint8_t *)(&ops[1]->ldpc_dec) +
> + DEC_OFFSET, CMP_DEC_SIZE) != 0) {
> + return false;
> + } else
> + return true;
> +}
> +
> +
> +/* Enqueue decode operations for ACC100 device in TB mode */
> +static uint16_t
> +acc100_enqueue_ldpc_dec_tb(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_dec_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + int32_t avail = q->sw_ring_depth + q->sw_ring_tail - q-
> >sw_ring_head;
> + uint16_t i, enqueued_cbs = 0;
> + uint8_t cbs_in_tb;
> + int ret;
> +
> + for (i = 0; i < num; ++i) {
> + cbs_in_tb = get_num_cbs_in_tb_ldpc_dec(&ops[i]-
> >ldpc_dec);
> + /* Check if there are available space for further processing */
> + if (unlikely(avail - cbs_in_tb < 0))
> + break;
> + avail -= cbs_in_tb;
> +
> + ret = enqueue_ldpc_dec_one_op_tb(q, ops[i],
> + enqueued_cbs, cbs_in_tb);
> + if (ret < 0)
> + break;
> + enqueued_cbs += ret;
> + }
> +
> + acc100_dma_enqueue(q, enqueued_cbs, &q_data->queue_stats);
> +
> + /* Update stats */
> + q_data->queue_stats.enqueued_count += i;
> + q_data->queue_stats.enqueue_err_count += num - i;
> + return i;
> +}
> +
> +/* Enqueue decode operations for ACC100 device in CB mode */
> +static uint16_t
> +acc100_enqueue_ldpc_dec_cb(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_dec_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + int32_t avail = q->sw_ring_depth + q->sw_ring_tail - q-
> >sw_ring_head;
> + uint16_t i;
> + union acc100_dma_desc *desc;
> + int ret;
> + bool same_op = false;
> + for (i = 0; i < num; ++i) {
> + /* Check if there are available space for further processing */
> + if (unlikely(avail - 1 < 0))
> + break;
> + avail -= 1;
> +
> + if (i > 0)
> + same_op = cmp_ldpc_dec_op(&ops[i-1]);
> + rte_bbdev_log(INFO,
> "Op %d %d %d %d %d %d %d %d %d %d %d %d\n",
> + i, ops[i]->ldpc_dec.op_flags, ops[i]-
> >ldpc_dec.rv_index,
> + ops[i]->ldpc_dec.iter_max, ops[i]-
> >ldpc_dec.iter_count,
> + ops[i]->ldpc_dec.basegraph, ops[i]->ldpc_dec.z_c,
> + ops[i]->ldpc_dec.n_cb, ops[i]->ldpc_dec.q_m,
> + ops[i]->ldpc_dec.n_filler, ops[i]-
> >ldpc_dec.cb_params.e,
> + same_op);
> + ret = enqueue_ldpc_dec_one_op_cb(q, ops[i], i, same_op);
> + if (ret < 0)
> + break;
> + }
> +
> + if (unlikely(i == 0))
> + return 0; /* Nothing to enqueue */
> +
> + /* Set SDone in last CB in enqueued ops for CB mode*/
> + desc = q->ring_addr + ((q->sw_ring_head + i - 1)
> + & q->sw_ring_wrap_mask);
> +
> + desc->req.sdone_enable = 1;
> + desc->req.irq_enable = q->irq_enable;
> +
> + acc100_dma_enqueue(q, i, &q_data->queue_stats);
> +
> + /* Update stats */
> + q_data->queue_stats.enqueued_count += i;
> + q_data->queue_stats.enqueue_err_count += num - i;
> + return i;
> +}
> +
> +/* Enqueue decode operations for ACC100 device. */
> +static uint16_t
> +acc100_enqueue_ldpc_dec(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_dec_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + int32_t aq_avail = q->aq_depth +
> + (q->aq_dequeued - q->aq_enqueued) / 128;
> +
> + if (unlikely((aq_avail == 0) || (num == 0)))
> + return 0;
> +
> + if (ops[0]->ldpc_dec.code_block_mode == 0)
> + return acc100_enqueue_ldpc_dec_tb(q_data, ops, num);
> + else
> + return acc100_enqueue_ldpc_dec_cb(q_data, ops, num);
> +}
> +
> +
> +/* Dequeue one encode operations from ACC100 device in CB mode */
> +static inline int
> +dequeue_enc_one_op_cb(struct acc100_queue *q, struct
> rte_bbdev_enc_op **ref_op,
> + uint16_t total_dequeued_cbs, uint32_t *aq_dequeued)
> +{
> + union acc100_dma_desc *desc, atom_desc;
> + union acc100_dma_rsp_desc rsp;
> + struct rte_bbdev_enc_op *op;
> + int i;
> +
> + desc = q->ring_addr + ((q->sw_ring_tail + total_dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> +
> + /* Check fdone bit */
> + if (!(atom_desc.rsp.val & ACC100_FDONE))
> + return -1;
> +
> + rsp.val = atom_desc.rsp.val;
> + rte_bbdev_log_debug("Resp. desc %p: %x", desc, rsp.val);
> +
> + /* Dequeue */
> + op = desc->req.op_addr;
> +
> + /* Clearing status, it will be set based on response */
> + op->status = 0;
> +
> + op->status |= ((rsp.input_err)
> + ? (1 << RTE_BBDEV_DATA_ERROR) : 0);
> + op->status |= ((rsp.dma_err) ? (1 << RTE_BBDEV_DRV_ERROR) : 0);
> + op->status |= ((rsp.fcw_err) ? (1 << RTE_BBDEV_DRV_ERROR) : 0);
> +
> + if (desc->req.last_desc_in_batch) {
> + (*aq_dequeued)++;
> + desc->req.last_desc_in_batch = 0;
> + }
> + desc->rsp.val = ACC100_DMA_DESC_TYPE;
> + desc->rsp.add_info_0 = 0; /*Reserved bits */
> + desc->rsp.add_info_1 = 0; /*Reserved bits */
> +
> + /* Flag that the muxing cause loss of opaque data */
> + op->opaque_data = (void *)-1;
> + for (i = 0 ; i < desc->req.numCBs; i++)
> + ref_op[i] = op;
> +
> + /* One CB (op) was successfully dequeued */
> + return desc->req.numCBs;
> +}
> +
> +/* Dequeue one encode operations from ACC100 device in TB mode */
> +static inline int
> +dequeue_enc_one_op_tb(struct acc100_queue *q, struct
> rte_bbdev_enc_op **ref_op,
> + uint16_t total_dequeued_cbs, uint32_t *aq_dequeued)
> +{
> + union acc100_dma_desc *desc, *last_desc, atom_desc;
> + union acc100_dma_rsp_desc rsp;
> + struct rte_bbdev_enc_op *op;
> + uint8_t i = 0;
> + uint16_t current_dequeued_cbs = 0, cbs_in_tb;
> +
> + desc = q->ring_addr + ((q->sw_ring_tail + total_dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> +
> + /* Check fdone bit */
> + if (!(atom_desc.rsp.val & ACC100_FDONE))
> + return -1;
> +
> + /* Get number of CBs in dequeued TB */
> + cbs_in_tb = desc->req.cbs_in_tb;
> + /* Get last CB */
> + last_desc = q->ring_addr + ((q->sw_ring_tail
> + + total_dequeued_cbs + cbs_in_tb - 1)
> + & q->sw_ring_wrap_mask);
> + /* Check if last CB in TB is ready to dequeue (and thus
> + * the whole TB) - checking sdone bit. If not return.
> + */
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)last_desc,
> + __ATOMIC_RELAXED);
> + if (!(atom_desc.rsp.val & ACC100_SDONE))
> + return -1;
> +
> + /* Dequeue */
> + op = desc->req.op_addr;
> +
> + /* Clearing status, it will be set based on response */
> + op->status = 0;
> +
> + while (i < cbs_in_tb) {
> + desc = q->ring_addr + ((q->sw_ring_tail
> + + total_dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> + rsp.val = atom_desc.rsp.val;
> + rte_bbdev_log_debug("Resp. desc %p: %x", desc,
> + rsp.val);
> +
> + op->status |= ((rsp.input_err)
> + ? (1 << RTE_BBDEV_DATA_ERROR) : 0);
> + op->status |= ((rsp.dma_err) ? (1 <<
> RTE_BBDEV_DRV_ERROR) : 0);
> + op->status |= ((rsp.fcw_err) ? (1 <<
> RTE_BBDEV_DRV_ERROR) : 0);
> +
> + if (desc->req.last_desc_in_batch) {
> + (*aq_dequeued)++;
> + desc->req.last_desc_in_batch = 0;
> + }
> + desc->rsp.val = ACC100_DMA_DESC_TYPE;
> + desc->rsp.add_info_0 = 0;
> + desc->rsp.add_info_1 = 0;
> + total_dequeued_cbs++;
> + current_dequeued_cbs++;
> + i++;
> + }
> +
> + *ref_op = op;
> +
> + return current_dequeued_cbs;
> +}
> +
> +/* Dequeue one decode operation from ACC100 device in CB mode */
> +static inline int
> +dequeue_dec_one_op_cb(struct rte_bbdev_queue_data *q_data,
> + struct acc100_queue *q, struct rte_bbdev_dec_op **ref_op,
> + uint16_t dequeued_cbs, uint32_t *aq_dequeued)
> +{
> + union acc100_dma_desc *desc, atom_desc;
> + union acc100_dma_rsp_desc rsp;
> + struct rte_bbdev_dec_op *op;
> +
> + desc = q->ring_addr + ((q->sw_ring_tail + dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> +
> + /* Check fdone bit */
> + if (!(atom_desc.rsp.val & ACC100_FDONE))
> + return -1;
> +
> + rsp.val = atom_desc.rsp.val;
> + rte_bbdev_log_debug("Resp. desc %p: %x", desc, rsp.val);
> +
> + /* Dequeue */
> + op = desc->req.op_addr;
> +
> + /* Clearing status, it will be set based on response */
> + op->status = 0;
> + op->status |= ((rsp.input_err)
> + ? (1 << RTE_BBDEV_DATA_ERROR) : 0);
> + op->status |= ((rsp.dma_err) ? (1 << RTE_BBDEV_DRV_ERROR) : 0);
> + op->status |= ((rsp.fcw_err) ? (1 << RTE_BBDEV_DRV_ERROR) : 0);
> + if (op->status != 0)
> + q_data->queue_stats.dequeue_err_count++;
> +
> + /* CRC invalid if error exists */
> + if (!op->status)
> + op->status |= rsp.crc_status << RTE_BBDEV_CRC_ERROR;
> + op->turbo_dec.iter_count = (uint8_t) rsp.iter_cnt / 2;
> + /* Check if this is the last desc in batch (Atomic Queue) */
> + if (desc->req.last_desc_in_batch) {
> + (*aq_dequeued)++;
> + desc->req.last_desc_in_batch = 0;
> + }
> + desc->rsp.val = ACC100_DMA_DESC_TYPE;
> + desc->rsp.add_info_0 = 0;
> + desc->rsp.add_info_1 = 0;
> + *ref_op = op;
> +
> + /* One CB (op) was successfully dequeued */
> + return 1;
> +}
> +
> +/* Dequeue one decode operations from ACC100 device in CB mode */
> +static inline int
> +dequeue_ldpc_dec_one_op_cb(struct rte_bbdev_queue_data *q_data,
> + struct acc100_queue *q, struct rte_bbdev_dec_op **ref_op,
> + uint16_t dequeued_cbs, uint32_t *aq_dequeued)
> +{
> + union acc100_dma_desc *desc, atom_desc;
> + union acc100_dma_rsp_desc rsp;
> + struct rte_bbdev_dec_op *op;
> +
> + desc = q->ring_addr + ((q->sw_ring_tail + dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> +
> + /* Check fdone bit */
> + if (!(atom_desc.rsp.val & ACC100_FDONE))
> + return -1;
> +
> + rsp.val = atom_desc.rsp.val;
> +
> + /* Dequeue */
> + op = desc->req.op_addr;
> +
> + /* Clearing status, it will be set based on response */
> + op->status = 0;
> + op->status |= rsp.input_err << RTE_BBDEV_DATA_ERROR;
> + op->status |= rsp.dma_err << RTE_BBDEV_DRV_ERROR;
> + op->status |= rsp.fcw_err << RTE_BBDEV_DRV_ERROR;
> + if (op->status != 0)
> + q_data->queue_stats.dequeue_err_count++;
> +
> + op->status |= rsp.crc_status << RTE_BBDEV_CRC_ERROR;
> + if (op->ldpc_dec.hard_output.length > 0 && !rsp.synd_ok)
> + op->status |= 1 << RTE_BBDEV_SYNDROME_ERROR;
> + op->ldpc_dec.iter_count = (uint8_t) rsp.iter_cnt;
> +
> + /* Check if this is the last desc in batch (Atomic Queue) */
> + if (desc->req.last_desc_in_batch) {
> + (*aq_dequeued)++;
> + desc->req.last_desc_in_batch = 0;
> + }
> +
> + desc->rsp.val = ACC100_DMA_DESC_TYPE;
> + desc->rsp.add_info_0 = 0;
> + desc->rsp.add_info_1 = 0;
> +
> + *ref_op = op;
> +
> + /* One CB (op) was successfully dequeued */
> + return 1;
> +}
> +
> +/* Dequeue one decode operations from ACC100 device in TB mode. */
> +static inline int
> +dequeue_dec_one_op_tb(struct acc100_queue *q, struct
> rte_bbdev_dec_op **ref_op,
> + uint16_t dequeued_cbs, uint32_t *aq_dequeued)
> +{
> + union acc100_dma_desc *desc, *last_desc, atom_desc;
> + union acc100_dma_rsp_desc rsp;
> + struct rte_bbdev_dec_op *op;
> + uint8_t cbs_in_tb = 1, cb_idx = 0;
> +
> + desc = q->ring_addr + ((q->sw_ring_tail + dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> +
> + /* Check fdone bit */
> + if (!(atom_desc.rsp.val & ACC100_FDONE))
> + return -1;
> +
> + /* Dequeue */
> + op = desc->req.op_addr;
> +
> + /* Get number of CBs in dequeued TB */
> + cbs_in_tb = desc->req.cbs_in_tb;
> + /* Get last CB */
> + last_desc = q->ring_addr + ((q->sw_ring_tail
> + + dequeued_cbs + cbs_in_tb - 1)
> + & q->sw_ring_wrap_mask);
> + /* Check if last CB in TB is ready to dequeue (and thus
> + * the whole TB) - checking sdone bit. If not return.
> + */
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)last_desc,
> + __ATOMIC_RELAXED);
> + if (!(atom_desc.rsp.val & ACC100_SDONE))
> + return -1;
> +
> + /* Clearing status, it will be set based on response */
> + op->status = 0;
> +
> + /* Read remaining CBs if exists */
> + while (cb_idx < cbs_in_tb) {
> + desc = q->ring_addr + ((q->sw_ring_tail + dequeued_cbs)
> + & q->sw_ring_wrap_mask);
> + atom_desc.atom_hdr = __atomic_load_n((uint64_t *)desc,
> + __ATOMIC_RELAXED);
> + rsp.val = atom_desc.rsp.val;
> + rte_bbdev_log_debug("Resp. desc %p: %x", desc,
> + rsp.val);
> +
> + op->status |= ((rsp.input_err)
> + ? (1 << RTE_BBDEV_DATA_ERROR) : 0);
> + op->status |= ((rsp.dma_err) ? (1 <<
> RTE_BBDEV_DRV_ERROR) : 0);
> + op->status |= ((rsp.fcw_err) ? (1 <<
> RTE_BBDEV_DRV_ERROR) : 0);
> +
> + /* CRC invalid if error exists */
> + if (!op->status)
> + op->status |= rsp.crc_status <<
> RTE_BBDEV_CRC_ERROR;
> + op->turbo_dec.iter_count = RTE_MAX((uint8_t) rsp.iter_cnt,
> + op->turbo_dec.iter_count);
> +
> + /* Check if this is the last desc in batch (Atomic Queue) */
> + if (desc->req.last_desc_in_batch) {
> + (*aq_dequeued)++;
> + desc->req.last_desc_in_batch = 0;
> + }
> + desc->rsp.val = ACC100_DMA_DESC_TYPE;
> + desc->rsp.add_info_0 = 0;
> + desc->rsp.add_info_1 = 0;
> + dequeued_cbs++;
> + cb_idx++;
> + }
> +
> + *ref_op = op;
> +
> + return cb_idx;
> +}
> +
> +/* Dequeue LDPC encode operations from ACC100 device. */
> +static uint16_t
> +acc100_dequeue_ldpc_enc(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_enc_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + uint32_t avail = q->sw_ring_head - q->sw_ring_tail;
> + uint32_t aq_dequeued = 0;
> + uint16_t dequeue_num, i, dequeued_cbs = 0, dequeued_descs = 0;
> + int ret;
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + if (unlikely(ops == 0 && q == NULL))
> + return 0;
> +#endif
> +
> + dequeue_num = (avail < num) ? avail : num;
> +
> + for (i = 0; i < dequeue_num; i++) {
> + ret = dequeue_enc_one_op_cb(q, &ops[dequeued_cbs],
> + dequeued_descs, &aq_dequeued);
> + if (ret < 0)
> + break;
> + dequeued_cbs += ret;
> + dequeued_descs++;
> + if (dequeued_cbs >= num)
> + break;
> + }
> +
> + q->aq_dequeued += aq_dequeued;
> + q->sw_ring_tail += dequeued_descs;
> +
> + /* Update enqueue stats */
> + q_data->queue_stats.dequeued_count += dequeued_cbs;
> +
> + return dequeued_cbs;
> +}
> +
> +/* Dequeue decode operations from ACC100 device. */
> +static uint16_t
> +acc100_dequeue_ldpc_dec(struct rte_bbdev_queue_data *q_data,
> + struct rte_bbdev_dec_op **ops, uint16_t num)
> +{
> + struct acc100_queue *q = q_data->queue_private;
> + uint16_t dequeue_num;
> + uint32_t avail = q->sw_ring_head - q->sw_ring_tail;
> + uint32_t aq_dequeued = 0;
> + uint16_t i;
> + uint16_t dequeued_cbs = 0;
> + struct rte_bbdev_dec_op *op;
> + int ret;
> +
> +#ifdef RTE_LIBRTE_BBDEV_DEBUG
> + if (unlikely(ops == 0 && q == NULL))
> + return 0;
> +#endif
> +
> + dequeue_num = (avail < num) ? avail : num;
> +
> + for (i = 0; i < dequeue_num; ++i) {
> + op = (q->ring_addr + ((q->sw_ring_tail + dequeued_cbs)
> + & q->sw_ring_wrap_mask))->req.op_addr;
> + if (op->ldpc_dec.code_block_mode == 0)
> + ret = dequeue_dec_one_op_tb(q, &ops[i],
> dequeued_cbs,
> + &aq_dequeued);
> + else
> + ret = dequeue_ldpc_dec_one_op_cb(
> + q_data, q, &ops[i], dequeued_cbs,
> + &aq_dequeued);
> +
> + if (ret < 0)
> + break;
> + dequeued_cbs += ret;
> + }
> +
> + q->aq_dequeued += aq_dequeued;
> + q->sw_ring_tail += dequeued_cbs;
> +
> + /* Update enqueue stats */
> + q_data->queue_stats.dequeued_count += i;
> +
> + return i;
> +}
> +
> /* Initialization Function */
> static void
> acc100_bbdev_init(struct rte_bbdev *dev, struct rte_pci_driver *drv)
> @@ -703,6 +2321,10 @@
> struct rte_pci_device *pci_dev = RTE_DEV_TO_PCI(dev->device);
>
> dev->dev_ops = &acc100_bbdev_ops;
> + dev->enqueue_ldpc_enc_ops = acc100_enqueue_ldpc_enc;
> + dev->enqueue_ldpc_dec_ops = acc100_enqueue_ldpc_dec;
> + dev->dequeue_ldpc_enc_ops = acc100_dequeue_ldpc_enc;
> + dev->dequeue_ldpc_dec_ops = acc100_dequeue_ldpc_dec;
>
> ((struct acc100_device *) dev->data->dev_private)->pf_device =
> !strcmp(drv->driver.name,
> @@ -815,4 +2437,3 @@ static int acc100_pci_remove(struct rte_pci_device
> *pci_dev)
> RTE_PMD_REGISTER_PCI_TABLE(ACC100PF_DRIVER_NAME,
> pci_id_acc100_pf_map);
> RTE_PMD_REGISTER_PCI(ACC100VF_DRIVER_NAME, acc100_pci_vf_driver);
> RTE_PMD_REGISTER_PCI_TABLE(ACC100VF_DRIVER_NAME,
> pci_id_acc100_vf_map);
> -
> diff --git a/drivers/baseband/acc100/rte_acc100_pmd.h
> b/drivers/baseband/acc100/rte_acc100_pmd.h
> index 0e2b79c..78686c1 100644
> --- a/drivers/baseband/acc100/rte_acc100_pmd.h
> +++ b/drivers/baseband/acc100/rte_acc100_pmd.h
> @@ -88,6 +88,8 @@
> #define TMPL_PRI_3 0x0f0e0d0c
> #define QUEUE_ENABLE 0x80000000 /* Bit to mark Queue as Enabled */
> #define WORDS_IN_ARAM_SIZE (128 * 1024 / 4)
> +#define ACC100_FDONE 0x80000000
> +#define ACC100_SDONE 0x40000000
>
> #define ACC100_NUM_TMPL 32
> #define VF_OFFSET_QOS 16 /* offset in Memory Space specific to QoS Mon
> */
> @@ -398,6 +400,7 @@ struct __rte_packed acc100_dma_req_desc {
> union acc100_dma_desc {
> struct acc100_dma_req_desc req;
> union acc100_dma_rsp_desc rsp;
> + uint64_t atom_hdr;
> };
>
>
> --
> 1.8.3.1
More information about the dev
mailing list