[dpdk-dev] [PATCH 4/4] net/hns3: fix FEC state query
Min Hu (Connor)
humin29 at huawei.com
Wed Dec 2 13:42:58 CET 2020
在 2020/11/20 22:35, Ferruh Yigit 写道:
> On 11/20/2020 2:33 PM, Ferruh Yigit wrote:
>> On 11/20/2020 11:27 AM, Lijun Ou wrote:
>>> From: "Min Hu (Conor)" <humin29 at huawei.com>
>>>
>>> As FEC is not supported below 10 Gbps, CMD(0x031A) offered
>>> from Firmware read will return fail in 10 Gbps device.
>>>
>>> This patch will prevent read this CMD when below 10 Gbps,
>>> as this is non-sense.
>>>
>>> Fixes: 9bf2ea8dbc65 ("net/hns3: support FEC")
>>> Cc: stable at dpdk.org
>>>
>>> Signed-off-by: Min Hu (Connor) <humin29 at huawei.com>
>>> Signed-off-by: Lijun Ou <oulijun at huawei.com>
>>> ---
>>> drivers/net/hns3/hns3_ethdev.c | 38
>>> ++++++++++++++++++++++++--------------
>>> 1 file changed, 24 insertions(+), 14 deletions(-)
>>>
>>> diff --git a/drivers/net/hns3/hns3_ethdev.c
>>> b/drivers/net/hns3/hns3_ethdev.c
>>> index d6d3f03..faa7b0a 100644
>>> --- a/drivers/net/hns3/hns3_ethdev.c
>>> +++ b/drivers/net/hns3/hns3_ethdev.c
>>> @@ -100,7 +100,7 @@ static int hns3_add_mc_addr(struct hns3_hw *hw,
>>> static int hns3_remove_mc_addr(struct hns3_hw *hw,
>>> struct rte_ether_addr *mac_addr);
>>> static int hns3_restore_fec(struct hns3_hw *hw);
>>> -static int hns3_query_dev_fec_info(struct rte_eth_dev *dev);
>>> +static int hns3_query_dev_fec_info(struct hns3_hw *hw);
>>> void hns3_ether_format_addr(char *buf, uint16_t size,
>>> const struct rte_ether_addr *ether_addr)
>>> @@ -3010,13 +3010,6 @@ hns3_get_capability(struct hns3_hw *hw)
>>> device_id == HNS3_DEV_ID_200G_RDMA)
>>> hns3_set_bit(hw->capability, HNS3_DEV_SUPPORT_DCB_B, 1);
>>> - ret = hns3_query_dev_fec_info(eth_dev);
>>> - if (ret) {
>>> - PMD_INIT_LOG(ERR,
>>> - "failed to query FEC information, ret = %d", ret);
>>> - return ret;
>>> - }
>>> -
>>> /* Get PCI revision id */
>>> ret = rte_pci_read_config(pci_dev, &revision,
>>> HNS3_PCI_REVISION_ID_LEN,
>>> HNS3_PCI_REVISION_ID);
>>> @@ -3148,8 +3141,15 @@ hns3_get_configuration(struct hns3_hw *hw)
>>> }
>>> ret = hns3_get_board_configuration(hw);
>>> - if (ret)
>>> + if (ret) {
>>> PMD_INIT_LOG(ERR, "failed to get board configuration: %d",
>>> ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = hns3_query_dev_fec_info(hw);
>>> + if (ret)
>>> + PMD_INIT_LOG(ERR,
>>> + "failed to query FEC information, ret = %d", ret);
>>> return ret;
>>> }
>>> @@ -5797,6 +5797,15 @@ get_current_fec_auto_state(struct hns3_hw *hw,
>>> uint8_t *state)
>>> struct hns3_cmd_desc desc;
>>> int ret;
>>> + /*
>>> + * CMD(0x031A) read is not supported in device of link speed
>>> + * below 10 Gbps.
>>> + */
>
> Also you can refer to "CMD(0x031A)" as 'HNS3_OPC_CONFIG_FEC_MODE', both
> in this comment and in the commit log, it is easier to understand than
> the numerical representation of the command.
thanks, Ferruh, oulijun will fix it and send V2.
>
>>> + if (hw->mac.link_speed < ETH_SPEED_NUM_10G) {
>>> + *state = 0;
>>> + return 0;
>>> + }
>>> +
>>> hns3_cmd_setup_basic_desc(&desc, HNS3_OPC_CONFIG_FEC_MODE, true);
>>> req = (struct hns3_config_fec_cmd *)desc.data;
>>> ret = hns3_cmd_send(hw, &desc, 1);
>>> @@ -6003,14 +6012,15 @@ hns3_restore_fec(struct hns3_hw *hw)
>>> }
>>> static int
>>> -hns3_query_dev_fec_info(struct rte_eth_dev *dev)
>>> +hns3_query_dev_fec_info(struct hns3_hw *hw)
>>> {
>>> - struct hns3_adapter *hns = dev->data->dev_private;
>>> - struct hns3_hw *hw = HNS3_DEV_PRIVATE_TO_HW(hns);
>>> - struct hns3_pf *pf = &hns->pf;
>>> + struct hns3_adapter *hns = HNS3_DEV_HW_TO_ADAPTER(hw);
>>> + struct hns3_pf *pf = HNS3_DEV_PRIVATE_TO_PF(hns);
>>> + struct rte_eth_dev *eth_dev;
>>> int ret;
>>> - ret = hns3_fec_get(dev, &pf->fec_mode);
>>> + eth_dev = &rte_eth_devices[hw->data->port_id];
>>
>> Not specific to this patch, but it is not good idea to access global
>> 'rte_eth_devices' array directly. Why not store the 'eth_dev' in the
>> device private data in the probe() and use it later?
>> Can you do a separate patch for this switch?
>> Thank you may not need to change the paramters of the
>> 'hns3_query_dev_fec_info()' or remove it from
>> 'hns3_query_dev_fec_info()' since you will be able to access to
>> 'eth_dev' easily.
Hi, Ferruh, I will fix it by doing a separate patch.
>>
>>> + ret = hns3_fec_get(eth_dev, &pf->fec_mode);
>>> if (ret)
>>> hns3_err(hw, "query device FEC info failed, ret = %d", ret);
>>>
>>
>
> .
More information about the dev
mailing list