[dpdk-dev] [PATCH] net/mlx5: update Tx datapath to support no inline hint

Viacheslav Ovsiienko viacheslavo at mellanox.com
Tue Jan 14 08:57:05 CET 2020


This patch adds support for dynamic flag that hints transmit
datapath do not copy data to the descriptors. This flag is
useful when data are located in the memory of another (not NIC)
physical device and copying to the host memory is undesirable.

This hint flag is per mbuf for multi-segment packets.

This hint flag might be partially ignored if:

- hardware requires minimal data header to be inline into
  descriptor, it depends on the hardware type and its configuration.
  In this case PMD copies the minimal required number of bytes to
  the descriptor, ignoring the no inline hint flag, the rest of data
  is not copied.

- VLAN tag insertion offload is requested and hardware does not
  support this options. In this case the VLAN tag is inserted by
  software means and at least 18B are copied to descriptor.

Signed-off-by: Viacheslav Ovsiienko <viacheslavo at mellanox.com>
---
RFC: http://patches.dpdk.org/patch/61348/

NOTE: This patch should be applied after the series:
"net/mlx5: add PMD dynf" http://patches.dpdk.org/patch/64542/

 drivers/net/mlx5/mlx5_rxtx.c | 104 ++++++++++++++++++++++++++++++++++++-------
 1 file changed, 88 insertions(+), 16 deletions(-)

diff --git a/drivers/net/mlx5/mlx5_rxtx.c b/drivers/net/mlx5/mlx5_rxtx.c
index aa6aa22..6cb5a2b 100644
--- a/drivers/net/mlx5/mlx5_rxtx.c
+++ b/drivers/net/mlx5/mlx5_rxtx.c
@@ -127,6 +127,7 @@ enum mlx5_txcmp_code {
 uint8_t mlx5_swp_types_table[1 << 10] __rte_cache_aligned;
 
 uint64_t rte_net_mlx5_dynf_inline_mask;
+#define PKT_TX_DYNF_NOINLINE rte_net_mlx5_dynf_inline_mask
 
 /**
  * Build a table to translate Rx completion flags to packet type.
@@ -2527,21 +2528,30 @@ enum mlx5_txcmp_code {
  *   Pointer to burst routine local context.
  * @param len
  *   Length of data to be copied.
+ * @param must
+ *   Length of data to be copied ignoring no inline hint.
  * @param olx
  *   Configured Tx offloads mask. It is fully defined at
  *   compile time and may be used for optimization.
+ *
+ * @return
+ *   Number of actual copied data bytes. This is always greater than or
+ *   equal to must parameter and might be lesser than len in no inline
+ *   hint flag is encountered.
  */
-static __rte_always_inline void
+static __rte_always_inline unsigned int
 mlx5_tx_mseg_memcpy(uint8_t *pdst,
 		    struct mlx5_txq_local *restrict loc,
 		    unsigned int len,
+		    unsigned int must,
 		    unsigned int olx __rte_unused)
 {
 	struct rte_mbuf *mbuf;
-	unsigned int part, dlen;
+	unsigned int part, dlen, copy = 0;
 	uint8_t *psrc;
 
 	assert(len);
+	assert(must <= len);
 	do {
 		/* Allow zero length packets, must check first. */
 		dlen = rte_pktmbuf_data_len(loc->mbuf);
@@ -2554,6 +2564,25 @@ enum mlx5_txcmp_code {
 			assert(loc->mbuf_nseg > 1);
 			assert(loc->mbuf);
 			--loc->mbuf_nseg;
+			if (loc->mbuf->ol_flags & PKT_TX_DYNF_NOINLINE) {
+				unsigned int diff;
+
+				if (copy >= must) {
+					/*
+					 * We already copied the minimal
+					 * requested amount of data.
+					 */
+					return copy;
+				}
+				diff = must - copy;
+				if (diff <= rte_pktmbuf_data_len(loc->mbuf)) {
+					/*
+					 * Copy only the minimal required
+					 * part of the data buffer.
+					 */
+					len = diff;
+				}
+			}
 			continue;
 		}
 		dlen -= loc->mbuf_off;
@@ -2561,6 +2590,7 @@ enum mlx5_txcmp_code {
 					       loc->mbuf_off);
 		part = RTE_MIN(len, dlen);
 		rte_memcpy(pdst, psrc, part);
+		copy += part;
 		loc->mbuf_off += part;
 		len -= part;
 		if (!len) {
@@ -2574,7 +2604,7 @@ enum mlx5_txcmp_code {
 				assert(loc->mbuf_nseg >= 1);
 				--loc->mbuf_nseg;
 			}
-			return;
+			return copy;
 		}
 		pdst += part;
 	} while (true);
@@ -2619,7 +2649,7 @@ enum mlx5_txcmp_code {
 	struct mlx5_wqe_eseg *restrict es = &wqe->eseg;
 	uint32_t csum;
 	uint8_t *pdst;
-	unsigned int part;
+	unsigned int part, tlen = 0;
 
 	/*
 	 * Calculate and set check sum flags first, uint32_t field
@@ -2652,17 +2682,18 @@ enum mlx5_txcmp_code {
 				 2 * RTE_ETHER_ADDR_LEN),
 		      "invalid Ethernet Segment data size");
 	assert(inlen >= MLX5_ESEG_MIN_INLINE_SIZE);
-	es->inline_hdr_sz = rte_cpu_to_be_16(inlen);
 	pdst = (uint8_t *)&es->inline_data;
 	if (MLX5_TXOFF_CONFIG(VLAN) && vlan) {
 		/* Implement VLAN tag insertion as part inline data. */
-		mlx5_tx_mseg_memcpy(pdst, loc, 2 * RTE_ETHER_ADDR_LEN, olx);
+		mlx5_tx_mseg_memcpy(pdst, loc,
+				    2 * RTE_ETHER_ADDR_LEN,
+				    2 * RTE_ETHER_ADDR_LEN, olx);
 		pdst += 2 * RTE_ETHER_ADDR_LEN;
 		*(unaligned_uint32_t *)pdst = rte_cpu_to_be_32
 						((RTE_ETHER_TYPE_VLAN << 16) |
 						 loc->mbuf->vlan_tci);
 		pdst += sizeof(struct rte_vlan_hdr);
-		inlen -= 2 * RTE_ETHER_ADDR_LEN + sizeof(struct rte_vlan_hdr);
+		tlen += 2 * RTE_ETHER_ADDR_LEN + sizeof(struct rte_vlan_hdr);
 	}
 	assert(pdst < (uint8_t *)txq->wqes_end);
 	/*
@@ -2670,18 +2701,26 @@ enum mlx5_txcmp_code {
 	 * Here we should be aware of WQE ring buffer wraparound only.
 	 */
 	part = (uint8_t *)txq->wqes_end - pdst;
-	part = RTE_MIN(part, inlen);
+	part = RTE_MIN(part, inlen - tlen);
 	assert(part);
 	do {
-		mlx5_tx_mseg_memcpy(pdst, loc, part, olx);
-		inlen -= part;
-		if (likely(!inlen)) {
-			pdst += part;
+		unsigned int copy;
+
+		/*
+		 * Copying may be interrupted inside the routine
+		 * if run into no inline hint flag.
+		 */
+		copy = tlen >= txq->inlen_mode ? 0 : (txq->inlen_mode - tlen);
+		copy = mlx5_tx_mseg_memcpy(pdst, loc, part, copy, olx);
+		tlen += copy;
+		if (likely(inlen <= tlen) || copy < part) {
+			es->inline_hdr_sz = rte_cpu_to_be_16(tlen);
+			pdst += copy;
 			pdst = RTE_PTR_ALIGN(pdst, MLX5_WSEG_SIZE);
 			return (struct mlx5_wqe_dseg *)pdst;
 		}
 		pdst = (uint8_t *)txq->wqes;
-		part = inlen;
+		part = inlen - tlen;
 	} while (true);
 }
 
@@ -3280,7 +3319,8 @@ enum mlx5_txcmp_code {
 	if (inlen <= MLX5_ESEG_MIN_INLINE_SIZE)
 		return MLX5_TXCMP_CODE_ERROR;
 	assert(txq->inlen_send >= MLX5_ESEG_MIN_INLINE_SIZE);
-	if (inlen > txq->inlen_send) {
+	if (inlen > txq->inlen_send ||
+	    loc->mbuf->ol_flags & PKT_TX_DYNF_NOINLINE) {
 		struct rte_mbuf *mbuf;
 		unsigned int nxlen;
 		uintptr_t start;
@@ -3295,7 +3335,8 @@ enum mlx5_txcmp_code {
 			assert(txq->inlen_mode <= txq->inlen_send);
 			inlen = txq->inlen_mode;
 		} else {
-			if (!vlan || txq->vlan_en) {
+			if (loc->mbuf->ol_flags & PKT_TX_DYNF_NOINLINE ||
+			    !vlan || txq->vlan_en) {
 				/*
 				 * VLAN insertion will be done inside by HW.
 				 * It is not utmost effective - VLAN flag is
@@ -4106,7 +4147,8 @@ enum mlx5_txcmp_code {
 				return MLX5_TXCMP_CODE_ERROR;
 			}
 			/* Inline or not inline - that's the Question. */
-			if (dlen > txq->inlen_empw)
+			if (dlen > txq->inlen_empw ||
+			    loc->mbuf->ol_flags & PKT_TX_DYNF_NOINLINE)
 				goto pointer_empw;
 			/* Inline entire packet, optional VLAN insertion. */
 			tlen = sizeof(dseg->bcount) + dlen;
@@ -4302,6 +4344,33 @@ enum mlx5_txcmp_code {
 				/* Check against minimal length. */
 				if (inlen <= MLX5_ESEG_MIN_INLINE_SIZE)
 					return MLX5_TXCMP_CODE_ERROR;
+				if (unlikely(loc->mbuf->ol_flags &
+					      PKT_TX_DYNF_NOINLINE)) {
+					/*
+					 * The hint flag not to inline packet
+					 * data is set. Check whether we can
+					 * follow the hint.
+					 */
+					if ((!MLX5_TXOFF_CONFIG(EMPW) &&
+					      txq->inlen_mode) ||
+					    (MLX5_TXOFF_CONFIG(MPW) &&
+					     txq->inlen_mode)) {
+						/*
+						 * The hardware requires the
+						 * minimal inline data header.
+						 */
+						goto single_min_inline;
+					}
+					if (MLX5_TXOFF_CONFIG(VLAN) &&
+					    vlan && !txq->vlan_en) {
+						/*
+						 * We must insert VLAN tag
+						 * by software means.
+						 */
+						goto single_part_inline;
+					}
+					goto single_no_inline;
+				}
 				/*
 				 * Completely inlined packet data WQE:
 				 * - Control Segment, SEND opcode
@@ -4351,6 +4420,7 @@ enum mlx5_txcmp_code {
 				 * We should check the free space in
 				 * WQE ring buffer to inline partially.
 				 */
+single_min_inline:
 				assert(txq->inlen_send >= txq->inlen_mode);
 				assert(inlen > txq->inlen_mode);
 				assert(txq->inlen_mode >=
@@ -4418,6 +4488,7 @@ enum mlx5_txcmp_code {
 				 * We also get here if VLAN insertion is not
 				 * supported by HW, the inline is enabled.
 				 */
+single_part_inline:
 				wqe = txq->wqes + (txq->wqe_ci & txq->wqe_m);
 				loc->wqe_last = wqe;
 				mlx5_tx_cseg_init(txq, loc, wqe, 4,
@@ -4458,6 +4529,7 @@ enum mlx5_txcmp_code {
 			 * - Ethernet Segment, optional VLAN, no inline
 			 * - Data Segment, pointer type
 			 */
+single_no_inline:
 			wqe = txq->wqes + (txq->wqe_ci & txq->wqe_m);
 			loc->wqe_last = wqe;
 			mlx5_tx_cseg_init(txq, loc, wqe, 3,
-- 
1.8.3.1



More information about the dev mailing list