[dpdk-dev] [PATCH v5 02/10] bbdev: expose device HARQ buffer size at device level
Dave Burley
dave.burley at accelercomm.com
Fri Mar 27 12:45:03 CET 2020
Acked-by: Dave Burley <dave.burley at accelercomm.com>
On 26/03/2020 03:27, Nicolas Chautru wrote:
> From: Nic Chautru <nicolas.chautru at intel.com>
>
> This exposes the HARQ buffer size at the device driver level
> instead of using the capability of a specific operation.
>
> This is currently not yet used by a device until
> future commit.
>
> Signed-off-by: Nic Chautru <nicolas.chautru at intel.com>
> ---
> drivers/baseband/turbo_sw/bbdev_turbo_software.c | 2 +-
> lib/librte_bbdev/rte_bbdev.h | 2 ++
> lib/librte_bbdev/rte_bbdev_op.h | 2 --
> 3 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/baseband/turbo_sw/bbdev_turbo_software.c b/drivers/baseband/turbo_sw/bbdev_turbo_software.c
> index f2fe7a2..6d5e080 100644
> --- a/drivers/baseband/turbo_sw/bbdev_turbo_software.c
> +++ b/drivers/baseband/turbo_sw/bbdev_turbo_software.c
> @@ -219,7 +219,6 @@ struct turbo_sw_queue {
> RTE_BBDEV_LDPC_ITERATION_STOP_ENABLE,
> .llr_size = 8,
> .llr_decimals = 2,
> - .harq_memory_size = 0,
> .num_buffers_src =
> RTE_BBDEV_LDPC_MAX_CODE_BLOCKS,
> .num_buffers_hard_out =
> @@ -251,6 +250,7 @@ struct turbo_sw_queue {
> dev_info->default_queue_conf = default_queue_conf;
> dev_info->capabilities = bbdev_capabilities;
> dev_info->min_alignment = 64;
> + dev_info->harq_buffer_size = 0;
>
> rte_bbdev_log_debug("got device info from %u\n", dev->data->dev_id);
> }
> diff --git a/lib/librte_bbdev/rte_bbdev.h b/lib/librte_bbdev/rte_bbdev.h
> index b2da190..38d9d50 100644
> --- a/lib/librte_bbdev/rte_bbdev.h
> +++ b/lib/librte_bbdev/rte_bbdev.h
> @@ -307,6 +307,8 @@ struct rte_bbdev_driver_info {
> bool queue_intr_supported;
> /** Minimum alignment of buffers, in bytes */
> uint16_t min_alignment;
> + /** HARQ memory available in kB */
> + uint32_t harq_buffer_size;
> /** Default queue configuration used if none is supplied */
> struct rte_bbdev_queue_conf default_queue_conf;
> /** Device operation capabilities */
> diff --git a/lib/librte_bbdev/rte_bbdev_op.h b/lib/librte_bbdev/rte_bbdev_op.h
> index c8a354e..80f3934 100644
> --- a/lib/librte_bbdev/rte_bbdev_op.h
> +++ b/lib/librte_bbdev/rte_bbdev_op.h
> @@ -712,8 +712,6 @@ struct rte_bbdev_op_cap_ldpc_dec {
> int8_t llr_size;
> /** LLR numbers of decimals bit for arithmetic representation */
> int8_t llr_decimals;
> - /** Amount of memory for HARQ in external DDR in MB */
> - uint16_t harq_memory_size;
> /** Num input code block buffers */
> uint16_t num_buffers_src;
> /** Num hard output code block buffers */
More information about the dev
mailing list