[dpdk-dev] [PATCH] net/ixgbe: delete MAC control frame fwd in struct adapter

[Sun, GuinanX]

Hi

> -----Original Message-----
> From: Zhao1, Wei
> Sent: Friday, May 22, 2020 5:47 PM
> To: Sun, GuinanX <guinanx.sun at intel.com>; dev at dpdk.org
> Cc: stable at dpdk.org; Yang, Qiming <qiming.yang at intel.com>; Ye, Xiaolong
> <xiaolong.ye at intel.com>
> Subject: RE: [PATCH] net/ixgbe: delete MAC control frame fwd in struct adapter
> 
> Hi,
> 
> > -----Original Message-----
> > From: Sun, GuinanX <guinanx.sun at intel.com>
> > Sent: Friday, May 22, 2020 2:12 PM
> > To: dev at dpdk.org
> > Cc: Zhao1, Wei <wei.zhao1 at intel.com>; Sun, GuinanX
> > <guinanx.sun at intel.com>; stable at dpdk.org
> > Subject: [PATCH] net/ixgbe: delete MAC control frame fwd in struct
> > adapter
> >
> > If some user set mac_ctrl_frame_fwd to 1 from fc ops, then he do a
> > port reset process of
> >
> > testpmd> start
> > testpmd> set flow_ctrl mac_ctrl_frame_fwd on 0 stop port stop 0 port
> > testpmd> start 0 start
> >
> > Then after this process, the mac_ctrl_frame_fwd has been change to
> > "off", so we should delete "adapter->mac_ctrl_frame_fwd = 0;" from dev-stop.
> >
> > In addition, add a value to mac_ctrl_frame_fwd in the
> > ixgbe_flow_ctrl_get () function.
> >
> > Fixes: a524f550da6e ("net/ixgbe: fix flow control mode setting")
> > Cc: stable at dpdk.org
> >
> > Signed-off-by: SunGuinan <guinanx.sun at intel.com>
> > ---
> >  drivers/net/ixgbe/ixgbe_ethdev.c | 4 ++--
> >  1 file changed, 2 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > b/drivers/net/ixgbe/ixgbe_ethdev.c
> > index f8a84c565..dd4023f01 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > @@ -2939,8 +2939,6 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
> >
> >  adapter->rss_reta_updated = 0;
> >
> > -adapter->mac_ctrl_frame_fwd = 0;
> > -
> >  hw->adapter_stopped = true;
> >  }
> >
> > @@ -4754,6 +4752,8 @@ ixgbe_flow_ctrl_get(struct rte_eth_dev *dev,
> > struct rte_eth_fc_conf *fc_conf)
> >   * MFLCN register.
> >   */
> >  mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
> > +fc_conf->mac_ctrl_frame_fwd = mflcn_reg;
> > +
> 
> 
> Error, that is not right!!

You are right, I will make corrections later.
In addition, the problem of ixgbe_flow_ctrl_get () and the timing of mac_ctrl_frame_fwd are two problems. 
I will make a patch set and release it later.

> 
> >  if (mflcn_reg & (IXGBE_MFLCN_RPFCE | IXGBE_MFLCN_RFCE))  rx_pause =
> > 1;  else
> > --
> > 2.17.1
>