[dpdk-dev] [PATCH v3 1/5] test/crypto: add lookaside IPsec tests

[Power, Ciara]

Hi Anoob,

Left some comments/questions inline.

Thanks,
Ciara

>-----Original Message-----
>From: Anoob Joseph <anoobj at marvell.com>
>Sent: Friday 3 September 2021 05:47
>To: Akhil Goyal <gakhil at marvell.com>; Doherty, Declan
><declan.doherty at intel.com>; Zhang, Roy Fan <roy.fan.zhang at intel.com>;
>Ananyev, Konstantin <konstantin.ananyev at intel.com>
>Cc: Anoob Joseph <anoobj at marvell.com>; Jerin Jacob <jerinj at marvell.com>;
>Archana Muniganti <marchana at marvell.com>; Tejasree Kondoj
><ktejasree at marvell.com>; Hemant Agrawal <hemant.agrawal at nxp.com>;
>Nicolau, Radu <radu.nicolau at intel.com>; Power, Ciara
><ciara.power at intel.com>; Gagandeep Singh <g.singh at nxp.com>; dev at dpdk.org
>Subject: [PATCH v3 1/5] test/crypto: add lookaside IPsec tests
>
>Added test case for lookaside IPsec. Inbound known vector tests are added.
>
>Cipher list: AES-GCM 128, 192 & 256
>
>Signed-off-by: Anoob Joseph <anoobj at marvell.com>
>Signed-off-by: Tejasree Kondoj <ktejasree at marvell.com>
>---
<snip>

> #ifdef RTE_LIB_SECURITY
> static int
>+ipsec_proto_testsuite_setup(void)
>+{
>+	struct crypto_testsuite_params *ts_params = &testsuite_params;
>+	struct crypto_unittest_params *ut_params = &unittest_params;
>+	struct rte_cryptodev_info dev_info;
>+
>+	rte_cryptodev_info_get(ts_params->valid_devs[0], &dev_info);
>+
>+	if (!(dev_info.feature_flags & RTE_CRYPTODEV_FF_SECURITY)) {
>+		RTE_LOG(INFO, USER1, "Feature flag requirements for IPsec
>Proto "
>+				"testsuite not met\n");
>+		return TEST_SKIPPED;
>+	}
>+
>+	/* Reconfigure to enable security */
>+	dev_configure_and_start(RTE_CRYPTODEV_FF_SYMMETRIC_CRYPTO |
>+				RTE_CRYPTODEV_FF_ASYMMETRIC_CRYPTO);
>+

Just a question on this - each testcase uses ut_setup_security which in turn calls dev_configure_and_start,
Is the configuration resulting from this call just being redone when the first testcase runs?

>+	/* Set action type */
>+	ut_params->type =
>RTE_SECURITY_ACTION_TYPE_LOOKASIDE_PROTOCOL;
>+
>+	if (security_proto_supported(
>+			RTE_SECURITY_ACTION_TYPE_LOOKASIDE_PROTOCOL,
>+			RTE_SECURITY_PROTOCOL_IPSEC) < 0) {
>+		RTE_LOG(INFO, USER1, "Capability requirements for IPsec Proto
>"
>+				"test not met\n");
>+		return TEST_SKIPPED;

If the test is skipped here, the device is not stopped, which I believe would cause problems for the next testsuite setup configuring the device.

>+	}
>+
>+	/* Stop the device */
>+	rte_cryptodev_stop(ts_params->valid_devs[0]);
>+
>+	return 0;
>+}