[PATCH V2 1/4] net/bonding: fix non-active slaves aren't stopped

[Min Hu (Connor)]

Hi, Ferruh,

在 2022/4/27 2:19, Ferruh Yigit 写道:
> On 3/24/2022 3:00 AM, Min Hu (Connor) wrote:
>> From: Huisong Li <lihuisong at huawei.com>
>>
>> When stopping a bonded port, all slaves should be deactivated. But only
> 
> s/deactivated/stopped/ ?
not agreed. deactivated and stopped are different state for slave.

> 
>> active slaves are stopped. So fix it and do "deactivae_slave()" for 
>> active
> 
> s/deactivae_slave()/deactivate_slave()/
> 
agreed.

>> slaves.
> 
> Hi Connor,
> 
> When a bonding port is closed, is it clear if all slave ports or active 
> slave ports should be stopped?
Yes, I think all the slave ports should be stopped(or try to be stopped).
> 
>>
>> Fixes: 0911d4ec0183 ("net/bonding: fix crash when stopping mode 4 port")
>> Cc: stable at dpdk.org
>>
>> Signed-off-by: Huisong Li <lihuisong at huawei.com>
>> Signed-off-by: Min Hu (Connor) <humin29 at huawei.com>
>> ---
>>   drivers/net/bonding/rte_eth_bond_pmd.c | 20 +++++++++++---------
>>   1 file changed, 11 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/net/bonding/rte_eth_bond_pmd.c 
>> b/drivers/net/bonding/rte_eth_bond_pmd.c
>> index b305b6a35b..469dc71170 100644
>> --- a/drivers/net/bonding/rte_eth_bond_pmd.c
>> +++ b/drivers/net/bonding/rte_eth_bond_pmd.c
>> @@ -2118,18 +2118,20 @@ bond_ethdev_stop(struct rte_eth_dev *eth_dev)
>>       internals->link_status_polling_enabled = 0;
>>       for (i = 0; i < internals->slave_count; i++) {
>>           uint16_t slave_id = internals->slaves[i].port_id;
>> +
>> +        internals->slaves[i].last_link_status = 0;
>> +        ret = rte_eth_dev_stop(slave_id);
>> +        if (ret != 0) {
>> +            RTE_BOND_LOG(ERR, "Failed to stop device on port %u",
>> +                     slave_id);
>> +            return ret;
> 
> Should it return here or try to stop all ports?
> What about to record the return status, but keep continue to stop all 
> ports. And return error if any of the stop failed?
I think no need to do this. APP only see the bonded device. If bonded
device stop failed, it means it works failed. And the number of 
"stopped" successfully slave does not make any sense.

> 
>> +        }
>> +
>> +        /* active slaves need to deactivate. */
> 
> " active slaves need to be deactivated. " ?
agreed.
> 
>>           if (find_slave_by_id(internals->active_slaves,
>>                   internals->active_slave_count, slave_id) !=
>> -                        internals->active_slave_count) {
>> -            internals->slaves[i].last_link_status = 0;
>> -            ret = rte_eth_dev_stop(slave_id);
>> -            if (ret != 0) {
>> -                RTE_BOND_LOG(ERR, "Failed to stop device on port %u",
>> -                         slave_id);
>> -                return ret;
>> -            }
>> +                internals->active_slave_count)
> 
> I think original indentation for this line is better.
> 
agreed.
>>               deactivate_slave(eth_dev, slave_id);
>> -        }
>>       }
>>       return 0;
> 
> .