[PATCH] net/bonding: make bonded device configure method re-entrant

[Chas Williams]

This appears to be correct. A minor comment inline.

On 10/17/22 04:42, Andrew Rybchenko wrote:
> Chas, Cornor, could you review the patch, please.
> 
> Thanks,
> Andrew.
> 
> On 9/11/22 15:24, Ivan Malov wrote:
>> According to the documentation, rte_eth_dev_configure()
>> can be invoked repeatedly while in stopped state.
>> The current implementation in the bonding driver
>> allows for that (technically), but the user sees
>> warnings which say that back-end devices have
>> already been harnessed. Re-factor the code
>> to have cleanup before each (re-)configure.
>>
>> Signed-off-by: Ivan Malov <ivan.malov at oktetlabs.ru>
>> Reviewed-by: Andrew Rybchenko <andrew.rybchenko at oktetlabs.ru>
>> ---
>>   drivers/net/bonding/rte_eth_bond_pmd.c | 27 ++++++++++++++++++--------
>>   1 file changed, 19 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/net/bonding/rte_eth_bond_pmd.c 
>> b/drivers/net/bonding/rte_eth_bond_pmd.c
>> index d01c954296..92a33b45bd 100644
>> --- a/drivers/net/bonding/rte_eth_bond_pmd.c
>> +++ b/drivers/net/bonding/rte_eth_bond_pmd.c
>> @@ -2143,18 +2143,13 @@ bond_ethdev_stop(struct rte_eth_dev *eth_dev)
>>       return 0;
>>   }
>> -int
>> -bond_ethdev_close(struct rte_eth_dev *dev)
>> +static void
>> +bond_ethdev_cfg_cleanup(struct rte_eth_dev *dev)
>>   {
>>       struct bond_dev_private *internals = dev->data->dev_private;
>>       uint16_t bond_port_id = internals->port_id;
>> -    int skipped = 0;
>>       struct rte_flow_error ferror;
>> -
>> -    if (rte_eal_process_type() != RTE_PROC_PRIMARY)
>> -        return 0;
>> -
>> -    RTE_BOND_LOG(INFO, "Closing bonded device %s", dev->device->name);
>> +    int skipped = 0;
>>       /* Flush flows in all back-end devices before removing them */
>>       bond_flow_ops.flush(dev, &ferror);
>> @@ -2176,6 +2171,20 @@ bond_ethdev_close(struct rte_eth_dev *dev)
>>               skipped++;
>>           }
>>       }
>> +}
>> +
>> +int
>> +bond_ethdev_close(struct rte_eth_dev *dev)
>> +{
>> +    struct bond_dev_private *internals = dev->data->dev_private;
>> +
>> +    if (rte_eal_process_type() != RTE_PROC_PRIMARY)
>> +        return 0;
>> +
>> +    RTE_BOND_LOG(INFO, "Closing bonded device %s", dev->device->name);
>> +
>> +    bond_ethdev_cfg_cleanup(dev);
>> +
>>       bond_ethdev_free_queues(dev);
>>       rte_bitmap_reset(internals->vlan_filter_bmp);
>>       rte_bitmap_free(internals->vlan_filter_bmp);
>> @@ -3606,6 +3615,8 @@ bond_ethdev_configure(struct rte_eth_dev *dev)
>>       unsigned i, j;
>> +    bond_ethdev_cfg_cleanup(dev);
>> +

You might want a space after the variable declaration section. It makes
it easier to read.

>>       /*
>>        * If RSS is enabled, fill table with default values and
>>        * set key to the value specified in port RSS configuration.
>