[PATCH v2 2/5] bbdev: add new capabilities for FFT processing

Maxime Coquelin maxime.coquelin at redhat.com
Mon Sep 18 17:08:13 CEST 2023


On 6/15/23 18:48, Nicolas Chautru wrote:
> Extending existing FFT operation for new capabilities.
> Optional frequency domain dewindowing, frequency resampling,
> timing error correction and time offset per CS.
> 
> Signed-off-by: Nicolas Chautru <nicolas.chautru at intel.com>
> ---
>   doc/guides/prog_guide/bbdev.rst | 24 ++++++++++++++++++++++++
>   lib/bbdev/rte_bbdev_op.h        | 23 ++++++++++++++++++++++-
>   2 files changed, 46 insertions(+), 1 deletion(-)
> 
> diff --git a/doc/guides/prog_guide/bbdev.rst b/doc/guides/prog_guide/bbdev.rst
> index 8e384015ee..95b33562fe 100644
> --- a/doc/guides/prog_guide/bbdev.rst
> +++ b/doc/guides/prog_guide/bbdev.rst
> @@ -1111,6 +1111,18 @@ with the operation flags forming a bitmask in the ``op_flags`` field.
>   |RTE_BBDEV_FFT_FP16_OUTPUT                                           |
>   | Set if the output data shall use FP16 format instead of INT16      |
>   +--------------------------------------------------------------------+
> +|RTE_BBDEV_FFT_TIMING_OFFSET_PER_CS                                  |
> +| Set if device supports adjusting time offset per CS                |
> ++--------------------------------------------------------------------+
> +|RTE_BBDEV_FFT_TIMING_ERROR                                          |
> +| Set if device supports correcting for timing error                 |
> ++--------------------------------------------------------------------+
> +|RTE_BBDEV_FFT_DEWINDOWING                                           |
> +| Set if enabling the option FFT Dewindowing in Frequency domain     |
> ++--------------------------------------------------------------------+
> +|RTE_BBDEV_FFT_FREQ_RESAMPLING                                       |
> +| Set if device supports the optional frequency resampling           |
> ++--------------------------------------------------------------------+
>   
>   The FFT parameters are set out in the table below.
>   
> @@ -1121,6 +1133,8 @@ The FFT parameters are set out in the table below.
>   +-------------------------+--------------------------------------------------------------+
>   |base_output              |output data                                                   |
>   +-------------------------+--------------------------------------------------------------+
> +|dewindowing_input        |optional frequency domain dewindowing input data              |
> ++-------------------------+--------------------------------------------------------------+
>   |power_meas_output        |optional output data with power measurement on DFT output     |
>   +-------------------------+--------------------------------------------------------------+
>   |op_flags                 |bitmask of all active operation capabilities                  |
> @@ -1155,6 +1169,16 @@ The FFT parameters are set out in the table below.
>   +-------------------------+--------------------------------------------------------------+
>   |fp16_exp_adjust          |value added to FP16 exponent at conversion from INT16         |
>   +-------------------------+--------------------------------------------------------------+
> +|freq_resample_mode       |frequency ressampling mode (0:transparent, 1-2: resample)     |
> ++-------------------------+--------------------------------------------------------------+
> +| output_depadded_size    |output depadded size prior to frequency resampling            |
> ++-------------------------+--------------------------------------------------------------+
> +|cs_theta_0               |timing error correction initial phase                         |
> ++-------------------------+--------------------------------------------------------------+
> +|cs_theta_d               |timing error correction phase increment                       |
> ++-------------------------+--------------------------------------------------------------+
> +|time_offset              |time offset per CS of time domain samples                     |
> ++-------------------------+--------------------------------------------------------------+
>   
>   The mbuf input ``base_input`` is mandatory for all bbdev PMDs and
>   is the incoming data for the processing. Its size may not fit into an actual mbuf,
> diff --git a/lib/bbdev/rte_bbdev_op.h b/lib/bbdev/rte_bbdev_op.h
> index 990d110fa7..682e265327 100644
> --- a/lib/bbdev/rte_bbdev_op.h
> +++ b/lib/bbdev/rte_bbdev_op.h
> @@ -50,6 +50,7 @@ extern "C" {
>   #define RTE_BBDEV_LDPC_MAX_CODE_BLOCKS (256)
>   /* 12 CS maximum */
>   #define RTE_BBDEV_MAX_CS_2 (6)
> +#define RTE_BBDEV_MAX_CS   (12)
>   /* MLD-TS up to 4 layers */
>   #define RTE_BBDEV_MAX_MLD_LAYERS (4)
>   /* 12 SB per RB */
> @@ -242,7 +243,15 @@ enum rte_bbdev_op_fft_flag_bitmasks {
>   	/** Set if the input data used FP16 format. */
>   	RTE_BBDEV_FFT_FP16_INPUT = (1ULL << 6),
>   	/** Set if the output data uses FP16 format. */
> -	RTE_BBDEV_FFT_FP16_OUTPUT = (1ULL << 7)
> +	RTE_BBDEV_FFT_FP16_OUTPUT = (1ULL << 7),
> +	/** Flexible adjustment of Timing offset adjustment per CS. */
> +	RTE_BBDEV_FFT_TIMING_OFFSET_PER_CS = (1ULL << 8),
> +	/** Flexible adjustment of Timing error correction per CS. */
> +	RTE_BBDEV_FFT_TIMING_ERROR = (1ULL << 9),
> +	/** Set for optional frequency domain dewindowing. */
> +	RTE_BBDEV_FFT_DEWINDOWING = (1ULL << 10),
> +	/** Flexible adjustment of frequency resampling mode. */
> +	RTE_BBDEV_FFT_FREQ_RESAMPLING = (1ULL << 11)
>   };
>   
>   /** Flags for MLDTS operation and capability structure */
> @@ -756,6 +765,8 @@ struct rte_bbdev_op_fft {
>   	struct rte_bbdev_op_data base_input;
>   	/** Output data starting from first antenna and first cyclic shift. */
>   	struct rte_bbdev_op_data base_output;
> +	/** Optional frequency window input data. */
> +	struct rte_bbdev_op_data dewindowing_input;
>   	/** Optional power measurement output data. */
>   	struct rte_bbdev_op_data power_meas_output;
>   	/** Flags from rte_bbdev_op_fft_flag_bitmasks. */
> @@ -790,6 +801,16 @@ struct rte_bbdev_op_fft {
>   	uint16_t power_shift;
>   	/** Adjust the FP6 exponent for INT<->FP16 conversion. */
>   	uint16_t fp16_exp_adjust;
> +	/** Frequency resampling : 0: Transparent Mode1: 4/3 Resample2: 2/3 Resample. */
> +	int8_t freq_resample_mode;
> +	/** Output depadded size prior to frequency resampling. */
> +	uint16_t output_depadded_size;
> +	/** Time error correction initial phase. */
> +	uint16_t cs_theta_0[RTE_BBDEV_MAX_CS];
> +	/** Time error correction phase increment. */
> +	uint32_t cs_theta_d[RTE_BBDEV_MAX_CS];
> +	/* Time offset per CS of time domain samples. */
> +	int8_t time_offset[RTE_BBDEV_MAX_CS];
>   };
>   /* >8 End of structure rte_bbdev_op_fft. */
>   

I think you need to document ABI change in:
doc/guides/rel_notes/release_23_11.rst

Once done, please add my:
Acked-by: Maxime Coquelin <maxime.coquelin at redhat.com>

Maxime




More information about the dev mailing list