[PATCH v2 2/6] common/sfc_efx/base: indicate dummy netport properties on VF

[Ivan Malov]

Starting with MCFW version 1.4.0.8, Medford4 adapters support the use
of the netport MCDI for port configuration by a VF; however, the MCDI
which retrieves fixed port properties is not permitted for use by VFs.

Fill in dummy values sufficient for the DPDK driver to start on a VF.

Signed-off-by: Ivan Malov <ivan.malov at arknetworks.am>
Reviewed-by: Andy Moreton <andy.moreton at amd.com>
---
 drivers/common/sfc_efx/base/efx_np.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)

diff --git a/drivers/common/sfc_efx/base/efx_np.c b/drivers/common/sfc_efx/base/efx_np.c
index 0e1cd35591..7a30567fe0 100644
--- a/drivers/common/sfc_efx/base/efx_np.c
+++ b/drivers/common/sfc_efx/base/efx_np.c
@@ -240,6 +240,7 @@ efx_np_get_fixed_port_props(
 	__out_opt		uint32_t *sup_cap_maskp,
 	__out_opt		efx_qword_t *loopback_cap_maskp)
 {
+	const efx_nic_cfg_t *encp = &enp->en_nic_cfg;
 	EFX_MCDI_DECLARE_BUF(payload,
 	    MC_CMD_GET_FIXED_PORT_PROPERTIES_IN_LEN,
 	    MC_CMD_GET_FIXED_PORT_PROPERTIES_OUT_V2_LEN);
@@ -247,6 +248,10 @@ efx_np_get_fixed_port_props(
 	efx_mcdi_req_t req;
 	efx_rc_t rc;
 
+	/* VFs do not allow access to the fixed port data. */
+	if (EFX_PCI_FUNCTION_IS_VF(encp))
+		return (0);
+
 	req.emr_out_length = MC_CMD_GET_FIXED_PORT_PROPERTIES_OUT_V2_LEN;
 	req.emr_in_length = MC_CMD_GET_FIXED_PORT_PROPERTIES_IN_LEN;
 	req.emr_cmd = MC_CMD_GET_FIXED_PORT_PROPERTIES;
@@ -1050,10 +1055,6 @@ efx_np_attach(
 	if (rc != 0)
 		goto fail1;
 
-	/*
-	 * FIXME: This may need revisiting for VFs, which
-	 * don't necessarily have access to these details.
-	 */
 	rc = efx_np_get_fixed_port_props(enp, epp->ep_np_handle,
 		    epp->ep_np_cap_data_raw, &epp->ep_phy_cap_mask,
 		    &epp->ep_np_loopback_cap_mask);
@@ -1071,6 +1072,23 @@ efx_np_attach(
 		epp->ep_phy_cap_mask |= 1U << EFX_PHY_CAP_AN;
 	}
 
+	/*
+	 * On VFs, 'efx_np_get_fixed_port_props' does not report any link
+	 * speeds; however, 'efx_np_link_state' should provide clues as
+	 * to which link speed is de facto active on the VF. Use this
+	 * clue to provide accurate information to the application.
+	 *
+	 * Also, indicate three basic capabilities that the VF cannot
+	 * manage, but that can be safely assumed to be available.
+	 */
+	if (EFX_PCI_FUNCTION_IS_VF(encp)) {
+		epp->ep_phy_cap_mask = epp->ep_adv_cap_mask;
+
+		epp->ep_phy_cap_mask |= 1U << EFX_PHY_CAP_PAUSE;
+		epp->ep_phy_cap_mask |= 1U << EFX_PHY_CAP_ASYM;
+		epp->ep_phy_cap_mask |= 1U << EFX_PHY_CAP_AN;
+	}
+
 #if EFSYS_OPT_LOOPBACK
 	efx_np_assign_loopback_props(enp);
 #endif /* EFSYS_OPT_LOOPBACK */
-- 
2.47.3