[dts] [dts 2/3] [PATCH V1] add tso test plan

huilong,xu huilongx.xu at intel.com
Mon Jun 1 09:09:34 CEST 2015
Previous message: [dts] [dts 1/3] [PATCH V1] add tso test for fortville NIC test
Next message: [dts] [dts 3/3] [PATCH V1] add tso test code
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
From: huilong xu <huilongx.xu at intel.com>


Signed-off-by: huilong xu <huilongx.xu at intel.com>
---
 test_plans/tso_test_plan.rst |  184 ++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 184 insertions(+), 0 deletions(-)
 create mode 100644 test_plans/tso_test_plan.rst

diff --git a/test_plans/tso_test_plan.rst b/test_plans/tso_test_plan.rst
new file mode 100644
index 0000000..8375607
--- /dev/null
+++ b/test_plans/tso_test_plan.rst
@@ -0,0 +1,184 @@
+# BSD LICENSE
+#
+# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+#   * Redistributions of source code must retain the above copyright
+#     notice, this list of conditions and the following disclaimer.
+#   * Redistributions in binary form must reproduce the above copyright
+#     notice, this list of conditions and the following disclaimer in
+#     the documentation and/or other materials provided with the
+#     distribution.
+#   * Neither the name of Intel Corporation nor the names of its
+#     contributors may be used to endorse or promote products derived
+#     from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+
+
+==============================================
+Testing of TSO Support in DPDK
+==============================================
+
+
+Description
+===========
+
+This document provides the plan for testing the TSO(Transmit Segmentation 
+Offload, also called Large Send offload - LSO) feature of
+Intel Ethernet Controller, including Intel 82599 10GbE Ethernet Controller and
+Fortville 40GbE Ethernet Controller. TSO enables the TCP/IP stack to
+pass to the network device a larger ULP datagram than the Maximum Transmit 
+Unit Size (MTU). NIC divides the large ULP datagram to multiple segments 
+according to the MTU size. 
+
+
+Prerequisites
+=============
+
+The DUT must take one of the Ethernet controller ports connected to a port on another 
+device that is controlled by the Scapy packet generator.
+
+The Ethernet interface identifier of the port that Scapy will use must be known.                
+On tester, all offload feature should be disabled on tx port, and start rx port capture:
+  ethtool -K <tx port> rx off tx off tso off gso off gro off lro off
+  ip l set <tx port> up
+  tcpdump -n -e -i <rx port> -s 0 -w /tmp/cap
+
+
+On DUT, run pmd with parameter "--enable-rx-cksum". Then enable TSO on tx port 
+and checksum on rx port. The test commands is below:
+  #enable hw checksum on rx port
+  tx_checksum set ip hw 0
+  tx_checksum set udp hw 0
+  tx_checksum set tcp hw 0
+  tx_checksum set sctp hw 0
+  set fwd csum
+
+  # enable TSO on tx port
+  *tso set 800 1 
+
+
+Test case: csum fwd engine, use TSO
+====================================================
+
+This test uses ``Scapy`` to send out one large TCP package. The dut forwards package 
+with TSO enable on tx port while rx port turns checksum on. After package send out 
+by TSO on tx port, the tester receives multiple small TCP package.
+
+Turn off tx port by ethtool on tester::
+  ethtool -K <tx port> rx off tx off tso off gso off gro off lro off
+  ip l set <tx port> up
+capture package rx port on tester::
+  tcpdump -n -e -i <rx port> -s 0 -w /tmp/cap
+  
+Launch the userland ``testpmd`` application on DUT as follows::
+./x86_64-native-linuxapp-gcc/app/testpmd -c 0xffffffff -n 2 -- -i --rxd=512 --txd=512 
+--burst=32 --rxfreet=64 --mbcache=128 --portmask=0x3 --txpt=36 --txht=0 --txwt=0 
+--txfreet=32 --txrst=32 --enable-rx-cksum
+  testpmd> set verbose 1
+
+  # enable hw checksum on rx port
+  testpmd> tx_checksum set ip hw 0
+  testpmd> tx_checksum set udp hw 0
+  testpmd> tx_checksum set tcp hw 0
+  testpmd> tx_checksum set sctp hw 0
+  # enable TSO on tx port
+  testpmd> tso set 800 1
+  # set fwd engine and start
+  testpmd> set fwd csum
+  testpmd> start 
+
+Test IPv4() in scapy:
+    sendp([Ether(dst="%s", src="52:00:00:00:00:00")/IP(src="192.168.1.1",dst="192.168.1.2")/UDP(sport=1021,dport=1021)/Raw(load="\x50"*%s)], iface="%s")
+
+Test IPv6() in scapy:
+    sendp([Ether(dst="%s", src="52:00:00:00:00:00")/IPv6(src="FE80:0:0:0:200:1FF:FE00:200", dst="3555:5555:6666:6666:7777:7777:8888:8888")/UDP(sport=1021,dport=1021)/Raw(load="\x50"*%s)], iface="%s"
+
+Test case: csum fwd engine, use TSO tunneling
+====================================================
+
+This test uses ``Scapy`` to send out one large TCP package. The dut forwards package 
+with TSO enable on tx port while rx port turns checksum on. After package send out 
+by TSO on tx port, the tester receives multiple small TCP package.
+
+Turn off tx port by ethtool on tester::
+  ethtool -K <tx port> rx off tx off tso off gso off gro off lro off
+  ip l set <tx port> up
+capture package rx port on tester::
+  tcpdump -n -e -i <rx port> -s 0 -w /tmp/cap
+  
+Launch the userland ``testpmd`` application on DUT as follows::
+./x86_64-native-linuxapp-gcc/app/testpmd -c 0xffffffff -n 2 -- -i --rxd=512 --txd=512 
+--burst=32 --rxfreet=64 --mbcache=128 --portmask=0x3 --txpt=36 --txht=0 --txwt=0 
+--txfreet=32 --txrst=32 --enable-rx-cksum
+  testpmd> set verbose 1
+
+  # enable hw checksum on rx port
+  testpmd> tx_checksum set ip hw 0
+  testpmd> tx_checksum set udp hw 0
+  testpmd> tx_checksum set tcp hw 0
+  testpmd> tx_checksum set sctp hw 0
+  testpmd> tx_checksum set vxlan hw 0
+  testpmd> tx_checksum set nvgre hw 0
+  # enable TSO on tx port
+  testpmd> tso set 800 1
+  # set fwd engine and start
+  testpmd> set fwd csum
+  testpmd> start 
+
+Test vxlan() in scapy:
+    sendp([Ether(dst="%s",src="52:00:00:00:00:00")/IP(src="192.168.1.1",dst="192.168.1.2")/UDP(sport=1021,dport=4789)/VXLAN(vni=1234)/Ether(dst=%s,src="52:00:00:00:00:00")/IP(src="192.168.1.1",dst="192.168.1.2")/UDP(sport=1021,dport=1021)/Raw(load="\x50"*%s)], iface="%s"
+
+Test nvgre() in scapy:
+    sendp([Ether(dst="%s",src="52:00:00:00:00:00")/IP(src="192.168.1.1",dst="192.168.1.2",proto=47)/NVGRE()/Ether(dst=%s,src="52:00:00:00:00:00")/IP(src="192.168.1.1",dst="192.168.1.2")/TCP(sport="1021",dport="1021")/("X"*%s)], iface="%s")
+
+Test case: TSO performance
+====================================================
+Set the packet stream to be sent out from packet generater before testing as 
+below.
+
++-------+---------+---------+---------+----------+----------+ 
+| Frame | 1S/1C/1T| 1S/1C/1T| 1S/2C/1T| 1S/2C/2T | 1S/2C/2T | 
+| Size  |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  64   |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  65   |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  128  |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  256  |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  512  |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  1024 |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  1280 |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+ 
+|  1518 |         |         |         |          |          | 
++-------+---------+---------+---------+----------+----------+
+
+Then run the test application as below:: 
+./x86_64-native-linuxapp-gcc/app/testpmd -c 0xffffffff -n 2 -- -i --rxd=512 --txd=512 
+--burst=32 --rxfreet=64 --mbcache=128 --portmask=0x3 --txpt=36 --txht=0 --txwt=0 
+--txfreet=32 --txrst=32 --enable-rx-cksum
+The -n command is used to select the number of memory channels. It should match the 
+number of memory channels on that setup.
+
+
-- 
1.7.4.4
Previous message: [dts] [dts 1/3] [PATCH V1] add tso test for fortville NIC test
Next message: [dts] [dts 3/3] [PATCH V1] add tso test code
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
More information about the dts mailing list