[dts] [PATCH 2/2] add TestSuite_pmdpcap rst into dts

[haifeng]

Signed-off-by: haifeng <haifengx.tang at intel.com>
---
 test_plans/pmdpcap_test_plan.rst | 100 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 100 insertions(+)
 create mode 100644 test_plans/pmdpcap_test_plan.rst

diff --git a/test_plans/pmdpcap_test_plan.rst b/test_plans/pmdpcap_test_plan.rst
new file mode 100644
index 0000000..d1434af
--- /dev/null
+++ b/test_plans/pmdpcap_test_plan.rst
@@ -0,0 +1,100 @@
+.. Copyright (c) <2010, 2011>, Intel Corporation
+   All rights reserved.
+   
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions
+   are met:
+   
+   - Redistributions of source code must retain the above copyright
+     notice, this list of conditions and the following disclaimer.
+   
+   - Redistributions in binary form must reproduce the above copyright
+     notice, this list of conditions and the following disclaimer in
+     the documentation and/or other materials provided with the
+     distribution.
+   
+   - Neither the name of Intel Corporation nor the names of its
+     contributors may be used to endorse or promote products derived
+     from this software without specific prior written permission.
+   
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+   OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=========================
+Tespt PMD PCAP files test
+=========================
+
+This document provides tests for the userland Intel(R)
+82599 Gigabit Ethernet Controller (Niantic) Poll Mode Driver (PMD) when using
+pcap files as input and output.
+
+The core configurations description is:
+
+- 2C/1T: 2 Physical Cores, 1 Logical Core per physical core
+- 4C/1T: 4 Physical Cores, 1 Logical Core per physical core
+
+Prerequisites
+=============
+
+This test does not requires connections between DUT and tester as it is focused
+in PCAP devices created by Test PMD.
+
+It is Test PMD application itself which send and receibes traffic from and to
+PCAP files, no traffic generator is involved.
+
+
+Test Case: test_send_packets_with_one_device
+============================================
+
+It is necessary to generate the input pcap file for one interface test. The
+pcap file can be created using scapy. Create a file with 1000 frames with the 
+following structure::
+
+  Ether(src='00:00:00:00:00:<last Eth>', dst='00:00:00:00:00:00')/IP(src='192.168.1.1', dst='192.168.1.2')/("X"*26))
+
+<last Eth> goes from 0 to 255 and repeats.
+
+The linuxapp is started with the following parameters:
+
+::
+
+  -c 0xffffff -n 3 --vdev 'eth_pcap0;rx_pcap=in.pcap;tx_pcap=out.pcap' --
+  -i --port-topology=chained
+
+
+Start the application and the forwarding, by typing `start` in the command line 
+of the application. After a few seconds `stop` the forwarding and `quit` the 
+application.
+
+Check that the frames of in.pcap and out.pcap files are the same using scapy.
+
+Test Case: test_send_packets_with_two_devices
+=============================================
+
+Create 2 pcap files with 1000 and 500 frames as explained in 
+`test_send_packets_with_one_device` test case. 
+
+The linuxapp is started with the following parameters:
+
+::
+
+  -c 0xffffff -n 3 --vdev 'eth_pcap0;rx_pcap=in1.pcap;tx_pcap=out1.pcap,"eth_pcap1;rx_pcap=in2.pcap;tx_pcap=out2.pcap'
+  -- -i
+
+
+Start the application and the forwarding, by typing `start` in the command line 
+of the application. After a few seconds `stop` the forwarding and `quit` the 
+application.
+
+Check that the frames of the in1.pcap and out2.pcap, and in2.pcap and out1.pcap
+file are the same using scapy.
-- 
1.9.3