[dts] [PATCH 1/2] test_plans: add test plan for userspace ethtool sample

[Yong Liu]

This sample is designed to demo the rte_ethtool shim layer based on
rte_ethdev API.

Signed-off-by: Marvin Liu <yong.liu at intel.com>

diff --git a/test_plans/userspace_ethtool_test_plan.rst b/test_plans/userspace_ethtool_test_plan.rst
new file mode 100644
index 0000000..18f5314
--- /dev/null
+++ b/test_plans/userspace_ethtool_test_plan.rst
@@ -0,0 +1,246 @@
+.. Copyright (c) <2015> Intel Corporation
+   All rights reserved.
+
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions
+   are met:
+
+   - Redistributions of source code must retain the above copyright
+     notice, this list of conditions and the following disclaimer.
+
+   - Redistributions in binary form must reproduce the above copyright
+     notice, this list of conditions and the following disclaimer in
+     the documentation and/or other materials provided with the
+     distribution.
+
+   - Neither the name of Intel Corporation nor the names of its
+     contributors may be used to endorse or promote products derived
+     from this software without specific prior written permission.
+
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+   OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==================
+ Userspace Ethtool
+==================
+
+This feature is designed to provide one rte_ethtool shim layer based on 
+rte_ethdev API. The implementation also along with a command prompt driven
+demonstration application. It only contained of 18 popular used Ethtool and
+Netdevice ops as described in rte_ethtool.h.
+
+Prerequisites
+=============
+
+Assume port 0 and 1 are connected to the traffic generator, to run the test
+application in linuxapp environment with 4 lcores, 2 ports.
+
+	ethtool -c f -n 4
+
+The sample should be validated on Forville, Niantic and i350 Nics. 
+
+Test Case: Dump driver infor test
+=================================
+User "drvinfo" command to dump driver information and then check that dumped
+information was exactly the same as fact.
+
+	EthApp> drvinfo
+	Port 0 driver: rte_ixgbe_pmd (ver: RTE 2.1.0)
+	Port 1 driver: rte_ixgbe_pmd (ver: RTE 2.1.0)
+
+Use "link" command to dump all ports link status.
+	EthApp> link
+	Port 0: Up
+	Port 1: Up
+
+Change tester port link status to down and re-check link status.
+	EthApp> link
+	Port 0: Down
+	Port 1: Down
+
+Send few packets to l2fwd and check that command "portstats" dumped correct
+port statistics.
+    EthApp> portstats 0
+    Port 0 stats
+       In: 1 (64 bytes)
+      Out: 1 (64 bytes)
+
+Test Case: Retrieve eeprom test
+===============================
+Unbind ports from igb_uio and bind them to default driver.
+Dump eeprom binary by ethtool.
+
+ethtool --eeprom-dump INTF_0 raw on > ethtool_eeprom_0.bin
+ethtool --eeprom-dump INTF_1 raw on > ethtool_eeprom_1.bin
+
+Retrieve eeprom on specified port and compare csum with the file dumped by ethtool.
+
+	EthApp> eeprom 0 eeprom_0.bin
+	EthApp> eeprom 1 eeprom_1.bin
+
+md5sum ethtool_eeprom_0.bin
+md5sum eeprom_0.bin > eeprom_0.bin
+	
+diff ethtool_eeprom_0.hex eeprom_0.hex
+
+Test Case: Retrieve register test
+===============================
+Retrieve register on specified port, do not known how to check the binary?
+
+	EthApp> regs 0 reg_0.bin
+	EthApp> regs 1 reg_1.bin	
+
+Unbind ports from igb_uio and bind them to default driver.
+Check that dumped register information is correct.
+
+ethtool -d INTF_0 raw on file reg_0.bin
+ethtool -d INTF_1 raw on file reg_0.bin
+	
+Test Case: Ring param test
+==========================
+Dump port 0 ring size by ringparam command and check numbers are correct.
+
+EthApp> ringparam  0
+Port 0 ring paramaeters
+  Rx Pending: 128 (256 max)
+  Tx Pending: 4096 (4096 max)
+
+Change port 0 ring size by ringparam command and then verify Rx/Tx function.
+
+EthApp> ringparam  0 256 2048
+
+Recheck ring size by ringparam command.
+
+EthApp> ringparam  0
+Port 0 ring paramaeters
+  Rx Pending: 256 (256 max)
+  Tx Pending: 2048 (4096 max)
+	
+Test Case: Pause test
+=====================
+Enable port 0 Rx pause frame and then create two packets flows in IXIA port.
+One flow is 100000 normally packet and the second flow is pause frame.
+Check that port 0 Rx speed dropped. For example, niantic will drop from
+14.8Mpps to 7.49Mpps.
+
+	EthApp> pause 0 rx
+
+Use "parse" command to print port pause status, check that port 0 rx has been
+paused.
+	EthApp> pause 0
+	Port 0: Rx Paused
+
+Unpause port 0 rx and then restart port0, check that packets Rx speed is normal.
+	EthApp> pause 0 none
+    EthApp> 
+
+Pause port 0 TX pause frame.
+	EthApp> pause 0 tx
+
+Use "parse" command to print port pause status, check that port 1 tx has been
+paused.
+    EthApp> pause 0
+    Port 0: Tx Paused
+
+Enable flow control in IXIA port and send packets from IXIA with line rate.
+Check that IXIA receive flow control packets and IXIA transmit speed dropped.
+IXIA Rx packets more then Tx packets to check that received pause frame.
+
+Unpause port 0 tx and restart port 0. Then send packets to port0, check that
+packets forwarded normally from port 0.
+	EthApp> pause 0 none
+    EthApp> stop 0
+    EthApp> open 0
+
+Test Case: Vlan test
+====================
+Add vlan 0 to port 0 and vlan 1 to port1, send packet without vlan to port0,1
+Verify port0 and port1 recevied vlan packets
+	EthApp> vlan 0 add 0
+	VLAN vid 0 added
+
+	EthApp> vlan 1 add 1
+	VLAN vid 1 added
+	
+Send packet with vlan0,1 to port0&1. Verify port0 and port1 received vlan
+packets
+
+Send packet with vlan1,0 to port0&1. Verify port0 and port1 can not receive
+vlan packets
+
+Remove vlan 0,1 from port0&1, send packet with vlan0,1 to port0,1. Verify
+port0 and port1 can not receive vlan packet.
+
+    EthApp> vlan 0 del 0
+	VLAN vid 0 removed
+	EthApp> vlan 1 del 1
+	VLAN vid 1 removed
+
+Test Case: Mac address test
+===========================
+Use "macaddr" command to dump port mac address and then check that dumped
+information is exactly the same as fact.
+	EthApp> macaddr 0
+	Port 0 MAC Address: XX:XX:XX:XX:XX:XX
+	EthApp> macaddr 1
+	Port 1 MAC Address: YY:YY:YY:YY:YY:YY
+
+Check mulitcast macaddress will not be valided.
+	EthApp> validate 01:00:00:00:00:00
+	Address is not unicast
+
+Check all zero macaddress will not be valided.	
+	EthApp> validate 00:00:00:00:00:00
+	Address is not unicast
+
+Use "macaddr" command to change port mac address and then check mac changed.
+	EthApp> validate 00:10:00:00:00:00
+	Address is unicast
+
+	EthApp> macaddr 0 00:10:00:00:00:00
+	MAC address changed
+	EthApp> macaddr 0
+	Port 0 MAC Address: 00:10:00:00:00:00
+	
+Verified  mac adress in forwarded packets has been changed.
+
+Test Case: Port config test
+===========================
+Use "stop" command to stop port0. Send packets to port0 and verify no packet
+recevied.
+	EthApp> stop 0
+	
+Use "open" command to re-enable port0. Send packets to port0 and verify
+packets received and forwarded.
+	EthApp> open 0
+
+
+Test case: Mtu config test
+==========================
+Use "mtu" command to change port 0 mtu from default 1518 to 1000.
+
+Send packet size over 1000 and check that packet will be detected as error.
+
+    EthApp> mtu 0 1000
+    Port 0 stats
+       In: 0 (0 bytes)
+      Out: 0 (0 bytes)
+      Err: 1
+
+Change mtu to default value and send packet size over 1000 and check that
+packet will normally received.
+	  
+Test Case: Rx mode test
+=======================
+Enable untagged vlan in VF devices and extended vlan support.
+Do not known how to test?
-- 
1.9.3