[dts] [PATCH] add ptype mapping test plan

Xueqin Lin xueqin.lin at intel.com
Mon Apr 24 05:45:15 CEST 2017


---
 test_plans/ptype_mapping_test_plan.rst | 305 +++++++++++++++++++++++++++++++++
 1 file changed, 305 insertions(+)
 create mode 100644 test_plans/ptype_mapping_test_plan.rst

diff --git a/test_plans/ptype_mapping_test_plan.rst b/test_plans/ptype_mapping_test_plan.rst
new file mode 100644
index 0000000..29de996
--- /dev/null
+++ b/test_plans/ptype_mapping_test_plan.rst
@@ -0,0 +1,305 @@
+.. Copyright (c) <2017>, Intel Corporation
+      All rights reserved.
+  
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions
+   are met:
+ 
+   - Redistributions of source code must retain the above copyright
+     notice, this list of conditions and the following disclaimer.
+   
+   - Redistributions in binary form must reproduce the above copyright
+     notice, this list of conditions and the following disclaimer in
+     the documentation and/or other materials provided with the
+     distribution.
+   
+   - Neither the name of Intel Corporation nor the names of its
+     contributors may be used to endorse or promote products derived
+     from this software without specific prior written permission.
+   
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+   OF THE POSSIBILITY OF SUCH DAMAGE.
+
+============================
+PTYPE mapping introduction
+============================
+
+All PTYPEs(packet types) in DPDK PMDs before are statically defined 
+using static constant map tables. It makes impossible to add a new 
+packet type without first defining them statically and then recompiling 
+DPDK. New NICs are flexible enough to be reconfigured depending on the 
+network environment. In case of FVL new PTYPEs can be added 
+dynamically at device initialization time using corresponding AQ 
+commands.
+Note that the packet types of the same packet recognized by different 
+hardware may be different, as different hardware may have different 
+capabilities of packet type recognition.
+
+This 32 bits of packet_type can be divided into several sub fields to
+indicate different packet type information of a packet. The initial design
+is to divide those bits into fields for L2 types, L3 types, L4 types, tunnel
+types, inner L2 types, inner L3 types and inner L4 types. All PMDs should
+translate the offloaded packet types into these 7 fields of information for
+user applications.
+
+
+Prerequisites
+=============
+Start testpmd, enable rxonly and verbose mode::
+        ./testpmd -c f -n 4 -- -i --port-topology=chained
+
+Test Case 1: Get ptype mapping
+===============================
+Get hardware defined ptype to software defined ptype mapping items::
+	testpmd> ptype mapping get <port_id> <valid_only>
+Note that valid_only parameter:: 
+	(0) target represents a specific software defined ptype.
+	(!0) target is a mask to represent a group of software defined ptypes.
+Check the table, first column is hardware ptype, second column is software 
+ptype. Take hw_ptype is 24 for example::
+	...
+	22     0x00000391
+	23     0x00000691
+	24     0x00000291
+	26     0x00000191
+	27     0x00000491
+	...
+	
+	[24] = RTE_PTYPE_L2_ETHER | RTE_PTYPE_L3_IPV4_EXT_UNKNOWN |
+							RTE_PTYPE_L4_UDP,
+
+RTE_PTYPE_L2_ETHER defined as 0x00000001,  
+RTE_PTYPE_L3_IPV4_EXT_UNKNOWN defined as 0x00000090,
+RTE_PTYPE_L4_UDP defined as 0x00000200, 
+Calculate with L2/L3/L4 mask, we can get the ptype is 0x00000291.
+
+1. Set <valid_only> as 0, Check that get 0~255 full columns ptype mapping 
+   items. 
+
+2. Set <valid_only> as 1, Check that get defined ptype mapping items. 
+
+3. Send packets, check RX dump packets software and hardware ptypes' 
+   correctness as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- ------+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4   | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP        | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | GRENAT     | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG    | 0x06426091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+   Dumped packet::
+        testpmd> port 0/queue 0: received 1 packets
+          src=00:00:00:00:00:00 - dst=FF:FF:FF:FF:FF:FF - type=0x0800 - 
+          length=122 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN 
+          TUNNEL_IP INNER_L3_IPV6_EXT_UNKNOWN INNER_L4_UDP - sw ptype: 
+          L2_ETHER L3_IPV4 TUNNEL_IP INNER_L3_IPV6 INNER_L4_UDP  - l2_len=14 
+          - l3_len=20 - tunnel_len=0 - inner_l3_len=40 - inner_l4_len=8 - 
+          Receive queue=0x0
+          ol_flags: PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD
+          port 0/queue 0: received 1 packets
+          src=00:00:00:00:00:00 - dst=FF:FF:FF:FF:FF:FF - type=0x0800 - 
+          length=120 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN 
+          TUNNEL_GRENAT INNER_L2_ETHER_VLAN INNER_L3_IPV4_EXT_UNKNOWN 
+          INNER_L4_NONFRAG  - sw ptype: L2_ETHER L3_IPV4 TUNNEL_NVGRE 
+          INNER_L2_ETHER_VLAN INNER_L3_IPV4  - l2_len=14 - l3_len=20 - 
+          tunnel_len=8 - inner_l2_len=18 - inner_l3_len=20 - Receive 
+          queue=0x0 ol_flags: PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD
+
+	
+Test Case 2: Reset ptype mapping
+================================
+1. Send packet and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	+------------+------------------+-------------+------------+------------+------------------+----- ----+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L  | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+----------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP      | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+------------------+----------+------------+---------+
+
+2. Check ptype mapping items: hw_ptype=38, sw_ptype=0x02601091
+
+3. Update hardware defined ptype to software defined packet type mapping table. 
+   Note that hw_ptype should among 0~255, sw_ptype should conform defined mask, 
+   e.g. change outer L3 value to 0x000000e0, which is IPV6_EXT_UNKNOWN::
+	testpmd> ptype mapping update 0 38 0x026010e1
+
+4. Check ptype mapping hw_ptype=38 and sw_ptype is updated to 0x026010e1
+
+5. Send packet and dump RX, check outer_L3 is changed to IPV6_EXT_UNKNOWN::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	
+6. Reset ptype mapping table to default::
+	testpmd> ptype mapping reset <port_id>
+	
+7. Check ptype mapping hw_ptype=38 and sw_ptype is updated to 0x02601091
+
+8. Send packet and dump RX, check outer_L3 is changed to IPV4_EXT_UNKNOWN 
+
+	
+Test Case 3: Update ptype mapping
+=================================
+1. Send packets and dump RX, check outer_L2, outer_L3, outer_L4, tunnel, 
+   inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- -----+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4  | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+-----------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP       | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | GRENAT     | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG   | 0x06426091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+-----------+------------+---------+
+	
+2. Get defined ptype mapping items, check when hw_ptype=38,sw_ptype is 0x02601091, 
+   when hw_ptype=75, sw_ptype is 0x06426091
+   
+3. Update hardware defined ptype to software defined packet type mapping table. 
+   Note that hw_ptype should among 0~255, sw_ptype should conform defined mask, 
+   e.g. change outer L3 value to 0x000000e0, which is IPV6_EXT_UNKNOWN::
+	testpmd> ptype mapping update 0 38 0x026010e1
+	
+4. Update [75]'s sw_ptype same to [38]'s sw_ptypes::
+	testpmd> ptype mapping update 0 75 0x026010e1
+
+5. Check ptype mapping items: when hw_ptype=38, sw_ptype is updated to value 
+   0x026010e1, when hw_ptype=75,sw_ptype is updated to value 0x026010e1
+	
+6. Send packets and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2, inner L3, inner L4 as below table, outer_L3 is changed to 
+   IPV6_EXT_UNKNOWN::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+	+------------+------------------+-------------+------------+------------+------------------+----- ------+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4   | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	| ETHER      | IPV6_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP        | 0x026010e1 |   38    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	| ETHER      | IPV6_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP        | 0x026010e1 |   75    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	
+7. Reset hardware defined ptype to software defined ptype mapping table to 
+   default::
+	testpmd> ptype mapping reset <port_id>
+
+8. Check ptype mapping items: when hw_ptype=38, sw_ptype is changed back to 
+   value 00x02601091, when hw_ptype=75, sw_ptype is changed back to 0x06426091
+
+9. Send packet and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- ------+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4   | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP        | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | GRENAT     | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG    | 0x06426091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	
+
+Test Case 4: Replace ptype mapping
+==================================
+Replace a specific or a group of software defined ptypes with a new one::
+	testpmd> ptype mapping replace <port_id> <target> <mask> <pkt_type>
+Note that target is the packet type to be replaced, pkt_type is the new packet 
+type to overwrite, mask is defined as below::
+	(0) target represents a specific software defined ptype.
+	(!0) target is a mask to represent a group of software defined ptypes.
+
+1. Send packets and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2,inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- ----+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4 | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+----- ----+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP      | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+------------------+----------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | GRENAT     | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG  | 0x06426091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+---- -----+------------+---------+
+	
+2. Replace a specific software defined ptypes with a new one.
+   e.g. change outer_L3 from Tunnel GRENAT to IP, 
+   so change mask from xxxx6xxx to xxxx1xxx::
+	testpmd> ptype mapping replace 0 0x06426091 0 0x06421091
+
+3. Update [38]'s sw_ptype same to [75]'s as 0x06421091::
+	testpmd> ptype mapping update 0 38 0x06421091
+	
+4. Send packet and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- ------+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4   | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG    | 0x06421091 |   38    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG    | 0x06421091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+
+5. Mapping table has at least two same sw_ptype 0x06421091, update a group of 
+   0x06421091 to 0x02601091::
+	testpmd> ptype mapping replace 0 0x06421091 1 0x02601091 
+	
+6. Check ptype mapping items: when hw_ptype=38, sw_ptype is updated to 
+   0x02601091, when hw_ptype=75, sw_ptype is updated to 0x02601091
+   
+7. Send packet and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+   inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- -----+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4  | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+-----------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP       | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP       | 0x02601091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------------------+------------+---------+
+
+8. Reset hardware defined ptype to software defined ptype mapping table to 
+   default::
+	testpmd> ptype mapping reset <port_id>
+
+9. Check ptype mapping items: when hw_ptype=38, sw_ptype is changed back to 
+   value 00x02601091, when hw_ptype=75, sw_ptype is changed back to 0x06426091
+
+10. Send packet and dump RX, check outer_L2, outer_L3, outer_L4, tunnel,
+    inner L2, inner L3, inner L4 as below table::
+	sendp([Ether()/IP()/IPv6()/UDP()/Raw('\0'*40)],iface=txItf)
+	sendp([Ether()/IP()/NVGRE()/Ether()/Dot1Q()/IP()/Raw('\0'*40)],iface=txItf)
+
+	+------------+------------------+-------------+------------+------------+------------------+----- ------+------------+---------+
+	| Outer L2   | Outer L3         | Outer L4    | Tunnel     | Inner L2   | Inner L3         | Inner L4   | sw_ptype   | hw_ptype|
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | IP         | Unknown    | IPV6_EXT_UNKNOWN | UDP        | 0x02601091 |   38    |
+	+------------+------------------+-------------+------------+------------+-------------------------------+------------+---------+
+	| ETHER      | IPV4_EXT_UNKNOWN | Unknown     | GRENAT     | ETHER_VLAN | IPV4_EXT_UNKNOWN | NONFRAG    | 0x06426091 |   75    |
+	+------------+------------------+-------------+------------+------------+------------------+------------+------------+---------+
+	
+
+
+
+
+
+
+
-- 
2.5.5



More information about the dts mailing list